Hostname: page-component-848d4c4894-4hhp2 Total loading time: 0 Render date: 2024-06-08T17:16:28.364Z Has data issue: false hasContentIssue false
  • English
  • Français

Effects of molybdenum on cellular precipitation in nickel-9 at. % tin alloy

Published online by Cambridge University Press:  18 February 2016

Archana Gupta ,
R. R. Nagarajan ,
A. K. Jena  and
M. C. Chaturvedi
Archana Gupta
Affiliation:
Department of Mechanical and Industrial Engineering, University of Manitoba, Winnipeg, Manitoba, Canada, R3T 2N2
R. R. Nagarajan
Affiliation:
Department of Metallurgical Engineering, Indian Institute of Technology, Kanpur, India, 208016
A. K. Jena
Affiliation:
Department of Metallurgical Engineering, Indian Institute of Technology, Kanpur, India, 208016
M. C. Chaturvedi
Affiliation:
Department of Mechanical and Industrial Engineering, University of Manitoba, Winnipeg, Manitoba, Canada, R3T 2N2
Get access

Extract

Lattice parameters, microanalysis, and microstructures of phases present in solution treated and aged samples of Ni-9 at. % Sn and Ni-9 at. % Sn-10 at. % Mo alloys have been investigated. Cellular precipitation was observed to occur in both alloys. During the initial stages of transformation the composition of the α-phase constituting the cells did not change with time. However, on formation of secondary and tertiary cells with interlamellar spacings much higher than those of the primary cells, the tin content of the α-phase of the cell decreased continuously with time and approached the equilibrium composition. The loss of supersaturation in the initial stages increased with decrease in temperature. Almost all of the molybdenum remained in the α-phase which contains 6.7 at. % Sn and 10.3 at. % Mo. Very little molybdenum partitioned to the compound which contained 24.9 at. % Sn and 0.40 at. % Mo. The presence of molybdenum considerably decreased the rate of nucleation and growth, reduced the interlamellar spacing, and increased the loss of supersaturation. However, the increase in hardness was observed to be small which is attributable primarily to solid solution hardening.

Type
Research Article
Information
Journal of Materials Research , Volume 8 , Issue 1 , January 1993 , pp. 95 - 99
Copyright
Copyright © Materials Research Society 1993

Access options

Get access to the full version of this content by using one of the access options below. (Log in options will check for institutional or personal access. Content may require purchase if you do not have access.)

References

1. Jones, B.L., J. Inst. Metals 99, 27 (1971).Google Scholar
2. Frebel, M., Predel, B., and Klisa, U., Z. Metallk. 65, 311, 469 (1974).Google Scholar
3. Klisa, U., Z. Metallk. 73, 627 (1982).Google Scholar
4. Miki, M. and Ogino, Y., Trans. Jpn. Inst. Metals 25(a), 603 (1984).Google Scholar
5. Miki, M. and Ogino, Y., Trans. Jpn. Inst. Metals 25(a), 611 (1984).Google Scholar
6. Jette, E. R. and Foote, F., Metallwirschaft 14, 165 (1935).Google Scholar
7. Mikula, W., Thomassen, L., and Upthegrove, C., Trans. AIME 124, 111 (1937).Google Scholar
8. Pearson, W. B. and Thompson, L. T., Can. J. Phys. 35, 349 (1957).Google Scholar
9. Jena, A. K., Gulati, D., and Ramachandran, T. R., Z. Metallk. 72, 847 (1981).Google Scholar
10. Hansen, M. and Anderko, K., Constitution of Binary Alloys (McGraw-Hill Book Co., New York, 1958).CrossRefGoogle Scholar
11. Pearson, W. B., A Handbook of Lattice Spacings (Pergamon Press, New York, 1967).Google Scholar
12. Kriege, O.H. and Baris, J.M., Trans. ASM 62, 195 (1969).Google Scholar
13. Jena, A.K. and Chaturvedi, M.C., J. Mater. Sci. 19, 3121 (1984).CrossRefGoogle Scholar
14. Pelloux, R.M.N. and Grant, N. J., Trans. Metall. Soc. AIME 218, 232 (1960).Google Scholar
15. Rama Brahman, I., Jena, A.K., and Chaturvedi, M.C., Scripta Metall. 23, 1281 (1989).Google Scholar