Hostname: page-component-848d4c4894-nr4z6 Total loading time: 0 Render date: 2024-05-31T13:23:22.305Z Has data issue: false hasContentIssue false
  • English
  • Français

Stress-life fatigue behavior and fracture-surface morphology of a Cu-based bulk-metallic glass

Published online by Cambridge University Press:  03 March 2011

M. Freels ,
P.K. Liaw ,
G.Y. Wang ,
Q.S. Zhang  and
Z.Q. Hu
M. Freels
Affiliation:
Department of Materials Science and Engineering, University of Tennessee, Knoxville, Tennessee 37996
P.K. Liaw*
Affiliation:
Department of Materials Science and Engineering, University of Tennessee, Knoxville, Tennessee 37996
G.Y. Wang
Affiliation:
Department of Materials Science and Engineering, University of Tennessee, Knoxville, Tennessee 37996
Q.S. Zhang
Affiliation:
Shenyang National Laboratory for Materials Science, Institute of Metal Research, Chinese Academy of Science, Shenyang 110016, PR China
Z.Q. Hu
Affiliation:
Shenyang National Laboratory for Materials Science, Institute of Metal Research, Chinese Academy of Science, Shenyang 110016, PR China
*
a) Address all correspondence to this author. e-mail: pliaw@utk.edu
Get access

Abstract

The stress-life fatigue behavior and fracture morphology of a (Cu60Zr30Ti10)99Sn1 bulk-metallic glass alloy was investigated under both three-point and four-point bending conditions. For all stress levels tested, the fatigue lifetimes tended to be higher for the three-point loading condition. The fatigue endurance limits (defined as 107 cycles without failure), based on the applied stress range, for three-point and four-point loading conditions were approximately 475 MPa and 350 MPa, respectively. All fracture surfaces were found to be composed of four main regions: a crack-initiation site, a stable crack-growth region, an unstable fast-fracture region, and a melting region. Finely spaced parallel marks, similar to fatigue striations found in crystalline alloys, oriented somewhat perpendicular to the direction of crack propagation were observed in the stable crack-growth region. Analyses of these marks found that their spacing increased with increasing stress-intensity-factor range. Damage was found to initiate from preexisting defects present on or near the surface.

Keywords

AmorphousScanning electron microscopy (SEM)Toughness
Type
Articles
Information
Journal of Materials Research , Volume 22 , Issue 2 , September 2006 , pp. 374 - 381
Copyright
Copyright © Materials Research Society 2007

Access options

Get access to the full version of this content by using one of the access options below. (Log in options will check for institutional or personal access. Content may require purchase if you do not have access.)

References

REFERENCES

1Salimon, A.I., Ashby, M.F., Bréchet, Y., and Greer, A.L.: Bulk metallic glasses: What are they good for? Mater. Sci. Eng., A 375–377, 385 (2004).CrossRefGoogle Scholar
2Li, H.Q., Fan, C., Tao, K.X., Choo, H., and Liaw, P.K.: Compressive behavior of a Zr-based metallic glass at cryogenic temperatures. Adv. Mater. 18, 752 (2006).CrossRefGoogle Scholar
3Fan, C., Liaw, P.K., Haas, V., Wall, J.J., Choo, H., Inoue, A., and Liu, C.T.: Structures and mechanical behaviors of Zr55Cu35Al10 bulk amorphous alloys at ambient and cryogenic temperatures. Phys. Rev. B: Condens. Matter 74, 014205 (2006).CrossRefGoogle Scholar
4Li, H.Q., Tao, K.X., Fan, C., Liaw, P.K., and Choo, H.: Effect of temperature on mechanical behavior of Zr-based bulk metallic glasses. Appl. Phys. Lett. 89, 041921 (2006).CrossRefGoogle Scholar
5Jiang, W.H., Liu, F., Qiao, D.C., Choo, H., and Liaw, P.K.: Plastic flow in dynamic compression of a Zr-based bulk metallic glass. J. Mater. Res. 21, 1570 (2006).CrossRefGoogle Scholar
6Hertzberg, R.: Deformation and Fracture Mechanics of Engineering Materials 4th ed. (Wiley, Hoboken, NJ, 1996).Google Scholar
7Gilbert, C.J., Lippman, J.M., and Ritchie, R.O.: Fatigue of a Zr-Ti-Cu-Ni-Be bulk amorphous metal: stress/life and crack-growth behavior. Scripta Mater. 38, 537 (1998).CrossRefGoogle Scholar
8Gilbert, C.J., Schroeder, V., and Ritchie, R.O.: Mechanisms for fracture and fatigue- crack propagation in a bulk metallic glass. Metall. Mater. Trans., A 30, 1739 (1999).CrossRefGoogle Scholar
9Flores, K.M., Johnson, W.L., and Dauskardt, R.H.: Fracture and fatigue behavior of a Zr–Ti–Nb ductile phase reinforced bulk metallic glass matrix composite. Scripta Mater. 49, 1181 (2003).CrossRefGoogle Scholar
10Flores, K.M. and Dauskardt, R.H.: Fracture and deformation of bulk metallic glasses and their composites. Intermetallics 12, 1025 (2004).CrossRefGoogle Scholar
11Wang, G.Y., Liaw, P.K., Peter, W.H., Yang, B., Yokoyama, Y., Benson, M.L., Kirkham, M.J., White, S.A., McDaniels, R.L., Saleh, T.A., Steward, R.V., Buchanan, R.A., Liu, C.T., and Brooks, C.R.: Fatigue behavior of bulk-metallic glasses. Inermetallics 12, 885 (2004).CrossRefGoogle Scholar
12Wang, G.Y., Liaw, P.K., Peter, W.H., Yang, B., Freels, M., Yokoyama, Y., Benson, M.L., Green, B.A., Saleh, T.A., McDaniels, R.L., Steward, R.V., Buchanan, R.A., Liu, C.T., and Brooks, C.R.: Fatigue behavior and fracture morphology of Zr50Al10Cu40 and Zr50Al10Cu30Ni10 bulk-metallic glasses. Intermetallics 12, 1219 (2004).CrossRefGoogle Scholar
13Wang, G.Y., Liaw, P.K., Peker, A., Yang, B., Yuan, W., Peter, W.H., Huang, L., Freels, M., Buchanan, R.A., Liu, C.T., and Brooks, C.R.: Fatigue behavior of Zr–Ti–Ni–Cu–Be bulk-metallic glasses. Intermetallics 13, 429 (2005).CrossRefGoogle Scholar
14Wang, G.Y., Liaw, P.K., Peker, A., Freels, M., Peter, W.H., Buchanan, R.A., and Brooks, C.R.: Comparison of fatigue behavior of a bulk metallic glass and its composite. Intermetallics 14, 1091 (2006).CrossRefGoogle Scholar
15Peter, W.H., Liaw, P.K., Buchanan, R.A., Liu, C.T., Brooks, C.R., Horton, J.A. Jr., Carmichael, C.A. Jr., and Wright, J.L.: Fatigue behavior of Zr52.5Al10Ti5Cu17.9Ni14.6 bulk metallic glass. Intermetallics 10, 1125 (2002).CrossRefGoogle Scholar
16Peter, W.H., Buchanan, R.A., Liu, C.T., and Liaw, P.K.: The fatigue behavior of a zirconium-based bulk metallic glass in vacuum and air. J. Non-Cryst. Solids 317, 187 (2003).CrossRefGoogle Scholar
17Yokoyama, Y., Fukaura, K., and Sunada, H.: Fatigue properties and microstructures of Zr55Cu30Al10Ni5 bulk glassy alloys. Mater. Trans., JIM 41, 675 (2000).CrossRefGoogle Scholar
18Zhang, Z.F., Eckert, J., and Schultz, L.: Tensile and fatigue fracture mechanisms of a Zr-based bulk metallic glass. J. Mater. Res. 18, 456 (2003).CrossRefGoogle Scholar
19Zhang, Z.F., Eckert, J., and Schultz, L.: Fatigue and fracture behavior of bulk metallic glass. Metall. Mater. Trans. A 35A, 3489 (2004).CrossRefGoogle Scholar
20Camaron, K.K. and Dauskardt, R.H.: Fatigue damage in bulk metallic glass I: Simulation. Scripta Mater. 54, 349 (2006).CrossRefGoogle Scholar
21Hess, P.A., Menzel, B.C., and Dauskardt, R.H.: Fatigue damage in bulk metallic glass II: Experiments. Scripta Mater. 54, 355 (2006).CrossRefGoogle Scholar
22Menzel, B.C. and Dauskardt, R.H.: Stress-life fatigue behavior of a Zr-based bulk metallic glass. Acta Mater. 54, 935 (2006).CrossRefGoogle Scholar
23Zhang, H., Wang, Z.G., Qiu, K.Q., Zang, Q.S., and Zhang, H.F.: Cyclic deformation and fatigue-crack propagation of a Zr-based bulk amorphous metal. Mater. Sci. Eng. A 356, 173 (2003).CrossRefGoogle Scholar
24Qiao, D.C., Liaw, P.K., Fan, C., Lin, Y.H., Wang, G.Y., Choo, H., and Buchanan, R.A.: Fatigue and fracture behavior of (Zr58Ni13.6Cu18Al10.4)99Nb1 bulk-amorphous alloy. Inermetallics 14, 1043 (2006).CrossRefGoogle Scholar
25Zhang, Q.S., Zhang, H.F., Deng, Y.F., Ding, B.Z., and Hu, Z.Q.: Cyclic softening of Zr55Al10Ni5Cu30 bulk amorphous alloy. Scripta Mater. 49, 273 (2003).CrossRefGoogle Scholar
26Inoue, A.: Stabilization of metallic supercooled liquid and bulk amorphous alloys. Acta Mater. 48, 279 (2000).CrossRefGoogle Scholar
27Baratta, F.I.: Requirements for flexure testing of brittle materials. ASTM STP. 844, 194 (1984).Google Scholar
28ASM International Handbook Vol. 11 edited by Richardson, D.W., (ASM, Metals Park, OH, 1990) pp. 746–747.Google Scholar
29Newman, J.C. and Raju, I.S.: NASA Technical Memorandum, 85793, 1984.Google Scholar
30Bates, R.C. and Clark, W.G. Jr.: Fractography and fracture mechanics. Transactions of the ASM 62, 380 (1969).Google Scholar