Hostname: page-component-848d4c4894-wg55d Total loading time: 0 Render date: 2024-06-07T07:21:58.678Z Has data issue: false hasContentIssue false
  • English
  • Français

Influence of Rare Earth Additions to an Inconel 718 Alloy

Published online by Cambridge University Press:  22 October 2020

Luis E. Gonzalez A. ,
Arnoldo Bedolla-Jacuinde ,
Francisco V. Guerra  and
A. Ruiz
Luis E. Gonzalez A.
Affiliation:
Instituto de Investigaciones en Metalurgia y Materiales, Universidad michoacana de San Nicolás de Hidalgo, Morelia, Michoacán, México.
Arnoldo Bedolla-Jacuinde*
Affiliation:
Instituto de Investigaciones en Metalurgia y Materiales, Universidad michoacana de San Nicolás de Hidalgo, Morelia, Michoacán, México.
Francisco V. Guerra
Affiliation:
Instituto de Investigaciones en Metalurgia y Materiales, Universidad michoacana de San Nicolás de Hidalgo, Morelia, Michoacán, México.
A. Ruiz
Affiliation:
Instituto de Investigaciones en Metalurgia y Materiales, Universidad michoacana de San Nicolás de Hidalgo, Morelia, Michoacán, México.
*
*Corresponding author: abedollj@umich.mx
Get access

Abstract

This work analyzes the effect of rare earth additions to an Inconel 718 superalloy; for this purpose, two 8 kg ingots of a commercial composition of Inconel 718 were made in a vacuum induction furnace. One of them (In718) with the base composition and the other one (In718RE) with an addition of 0.04wt% of mischmetal (rare earths alloy based on cerium and lanthanum). Both alloys were cast into metallic molds into the vacuum chamber and let to solidify. The alloys were then solubilized for two hours at 1155 °C to eliminate deleterious phases, rolled at 1100 °C to get a reduction of 50% in thickness, then aged for 16 hours at 720 °C and 620 °C by 8 hours each. A complete microstructural characterization was undertaken by optical and electronic (SEM and TEM) microscopy and X-ray diffraction. Mechanical characterization was done by hardness tests, tensile and Charpy impact tests. Results show a slight improvement of the tensile and hardness values for the alloy with rare earth additions. However, no notorious difference was observed during the impact tests, since both alloys show the same values. These mechanical results are discussed in terms of the obtained microstructure. Both alloys are mainly composed by γ, γ´, γ´´ and carbides. It was observed that primary carbides nucleate rare earth particles; therefore, higher number of carbides and of larger size (according to a size distribution) are observed in the alloy with rare earth additions. The presence of such carbides prevents the grain growth during the thermomechanical processing which in turn improve the mechanical properties.

Type
Articles
Information
MRS Advances , Volume 5 , Issue 59-60: International Materials Research Congress XXIX , 2020 , pp. 3035 - 3043
Check for updates
Copyright
Copyright © The Author(s), 2020, published on behalf of Materials Research Society by Cambridge University Press

Access options

Get access to the full version of this content by using one of the access options below. (Log in options will check for institutional or personal access. Content may require purchase if you do not have access.)

References

Reed R, C., The Superalloys: Fundamentals and Applications. Cambridge, UK: Cambridge University Press, (pags. 1–101) 2006.CrossRefGoogle Scholar
Kishan E, V R and Nagarajan N, M., Strengthening of Forged Inconel Superalloy by Age Hardening Heat Treatment, International Journal of Innovate Science, Engineering & Technology, Vol. 2, (pags. 387–391) 2015.Google Scholar
Lee, S-C, Chang, S-H, Tang, T, Ho, H-H and Chen J, K., Improvement in the Microstructure and Tensile Properties of Inconel 718 Superalloy by HIP Treatment, Materials Transactions, Vol. 47, (pags. 2877–2881) 2006.CrossRefGoogle Scholar
Wang, R.M., Song, Y.G., Han, Y.F., Effect of rare earth on the microstructures and properties of a low expansion superalloy, Journal of Alloys and Compounds, Vol. 311 (pags. 60–64) 2000.CrossRefGoogle Scholar
Committee, A I H., ASM handbook: Heat treating, Vol. 4, (pags. 1757–1813)1991.Google Scholar
Moiz, M., The influence of grain size on the mechanical properties of Inconel 718, Master Thesis, Department of Management and Engineering, Linköping University Sweden, 2013.Google Scholar
Aghajani, A, Tewes, J, Parsa A, B., Hoffmann, T, Kostka, A and Kloewer, J., Identification of Mo-Rich M23C6 Carbides in Alloy 718, Metallurgical and Materials Transactions, Vol. 47 (pags. 4382–4392) 2016.CrossRefGoogle Scholar
Medrano-Prieto H, M, Garay-Reyes C, G., Ruiz-Esparza-Rodriguez M, A, Estrada-Guel, I, Silva-Aceves J, M, Castro-Carmona J, S, Camacho-Montes, H and Martínez-Sánchez, R. Effect of Trace Ce/La Addition on the Microstructure and Microhardness of Nanostructured Nickel-based Superalloy Inconel 718, Microscopy and Microanalysis, Vol. 25, (pags. 2178–2179), 2019.CrossRefGoogle Scholar
Chen, Y-T, Yeh, A-C, Li, M-Y and Kuo, S-M., Effects of processing routes on room temperature tensile strength and elongation for Inconel 718, Materials & Design, Vol. 119, (pags. 235–243) 2017.CrossRefGoogle Scholar
Pei, C, Shi, D, Yuan, H and Li, H., Assessment of mechanical properties and fatigue performance of a selective laser melted nickel-base superalloy Inconel 718, Materials Science and Engineering A, Vol. 759, (pags. 278–287) 2019.CrossRefGoogle Scholar
Lu, Y, Wu, S, Gan, Y, Huang, T, Yang, C., Junjie, L and Lin, J. Study on the microstructure, mechanical property and residual stress of SLM Inconel-718 alloy manufactured by differing island scanning strategy, Optics & Laser Technology, Vol. 75, (pags. 197–206) 2015.CrossRefGoogle Scholar
Liu, F, Lin, X, Yang, G, Song, M, Chen, J and Huang, W., Microstructure and residual stress of laser rapid formed Inconel 718 nickel-base superalloy, Optics & Laser Technology, Vol. 43, (pags. 208–213) 2011.CrossRefGoogle Scholar
Mitchell, A., Primary Carbides in alloy 718, The Minerals, Metals & Materials Society, 7th International Symposium on Superalloy 718 and Derivatives, (pags. 161–167) 2010.CrossRefGoogle Scholar