Volume 63 - Issue 5 - October 2015
Article
CEC and 7Li MAS NMR Study of Interlayer Li+ in the Montmorillonite—Beidellite Series at Room Temperature and After Heating
- Annett Steudel, Ralf Heinzmann, Sylvio Indris, Katja Emmerich
-
- Published online by Cambridge University Press:
- 01 January 2024, pp. 337-350
-
- Article
- Export citation
-
The objective of the study was to contribute to the understanding of the influence of the structure and the 2:1 layer dimension of smectites on cation exchange capacity (CEC) reduction and the hydration behavior of Li-saturated smectites after heating. Five montmorillonites extracted from bentonites of different provenance were saturated with Li+ and heated to 300°C. Initial montmorillonites and montmorillonites with reduced layer charge (RCM) were characterized by comprehensive mineralogical analysis supplemented by CEC measurements, surface-area measurements by Ar adsorption, and 7Li, 27Al, and 29Si magic-angle spinning nuclear magnetic resonance spectroscopy (MAS NMR). The CEC of the initial montmorillonites varied between 89 and 130 cmol(+)/kg while the CEC of the RCM prepared at 300°C varied between 8 and 25 cmol(+)/kg. The lateral dimension of the 2:1 layers varied between 70 and 200 nm. The greatest decrease in CEC was observed for the montmorillonite with the largest diameter of the 2:1 layers and the smallest decrease was observed for the montmorillonite with the smallest diameter of the 2:1 layers. 7Li MAS NMR revealed an axially symmetric chemical environment of the hydrated interlayer Li+ with ηΔ = 0 for the chemical shift anisotropy tensor for unheated montmorillonites with >33% tetrahedral layer charge (ξ). The chemical environment is typical of innersphere hydration complexes of interlayer Li+. An axially non-symmetric chemical environment of the interlayer Li+ with ηCS of close to one was observed for all RCM. While the remaining CEC of RCM prepared at 300°C reflected the variable CEC at the edges, and thus the lateral size or aspect ratio of the 2:1 layers, the hydration complex of interlayer Li+ was strongly determined by the isomorphic substitutions in the dioctahedral 2:1 layers.
The Structure and Thermochemistry of Three Fe-Mg Chlorites
- Stephen Aja, Oladipo Omotoso, Christian Bertoldi, Edgar Dachs, Artur Benisek
-
- Published online by Cambridge University Press:
- 01 January 2024, pp. 351-367
-
- Article
- Export citation
-
Chlorites are petrogenetically important minerals, exercise controls on petroleum reservoir qualities, are common in alteration zones during hydrothermal ore mineralization, and may form during carbon sequestration in sedimentary formations. Chlorite thermochemistry and structure have been investigated, in the present study, to facilitate an improved understanding of chlorite equilibria.
Three natural IIb chlorites were studied by powder diffraction and calorimetric methods (low-temperature relaxation calorimetry using a Physical Properties Measurement System [PPMS] and differential scanning calorimetry [DSC]). The samples include a low-Fe clinochlore [Mg-Chl] and two Fe-rich chlorites from Windsor [Fe-Chl(W)] and Michigan [Fe-Chl(M)]. The structure of each chlorite was refined in the ideal C2/m symmetry using Rietveld techniques. Lattice parameters for the Windsor chlorite are a = 5.3786(6) Å, b = 9.3176(9) Å, c = 14.2187(6) Å, β = 96.98(10)°. The Michigan chlorite returned a = 5.3897(3) Å, b = 9.3300(3) Å, c = 14.2376(2) Å, β = 97.043(5)° whereas the low-Fe clinochlore yielded a = 5.3301(3) Å, b = 9.2231(8) Å, c = 14.2912(4) Å, β= 97.03(10)°.
Heat capacities (Cp) for the three natural chlorites were measured using both PPMS (2–303 K) and DSC (282–564 K). Employing a combination of Debye-Einstein-Schottky functions, the lattice dynamics component of the Cp at lower temperature was evaluated allowing a separation of the magnetic spin ordering component of Cp from the lattice vibrational part. For Mg-Chl, Fe-Chl(W), and Fe-Chl(M), the polynomials defining the temperature dependencies of the heat capacities between 280 and 570 K are:
Cp = 1185.44(±68.93) − 9753.21(±186.85)T−0.5 − 1.9094(±1.0288)·107T−2 + 3.3013(±1.5363)·109T−3
Cp = 1006.06(±48.46) − 4134.83 (±1515.16)T−0.5 − 40.0949(±6.9413)·106T−2 + 5.9386(±1.0287)·109T−3
and
Cp = 1268.60(±67.16) − 11983.09(±2107.07)T−0.5 − 7.6037(±9.6417)·106T−2 + 1.5398(±1.4187)·109T−3, respectively.
Standard state molar thermodynamic functions, CP, ST, (HT−H0)/T, and φ were evaluated for the samples. S298.15 for Fe-Chl(W), Mg-Chl, and Fe-Chl(M) were found to be 499.14 ± 3.40, 437.81 ± 3.00 and 515.06 ± 3.60 J mol-1K-1, respectively, whereas S° for Fe-Chl(W) and Mg-Chl were determined to be 578.24 ± 3.76 and 503.21 ± 3.60 J mol−1K−1, −1
Native Morphology of Hydrated Spheroidal Halloysite Observed by Environmental Transmission Electron Microscopy
- Jeremie Berthonneau, Olivier Grauby, Charlotte Jeannin, Damien Chaudanson, Emmanuel Joussein, Alain Baronnet
-
- Published online by Cambridge University Press:
- 01 January 2024, pp. 368-377
-
- Article
- Export citation
-
Natural mineral materials such as tabular and spheroidal halloysites have recently been suggested as candidates for intercalating metal ions or organic molecules. Their potential use as nanoadsorbents is related to their porous structure and water content. Although the two morphologies can coexist in natural deposits, spheroidal halloysites remain poorly characterized whereas much literature exists on tubular halloysites. The present study investigates the native morphology, internal porous structure, and behavior upon dehydration of spheroidal halloysite from Opotiki (New Zealand). This mineral was characterized in its natural hydrated state using a transmission electron microscope equipped with an environmental cell (EC-TEM). The sample was placed in a sealed block in which water vapor-saturated air circulated at a pressure of 30 Torr. The observed particles consisted of almost complete spheroids displaying polyhedral external surfaces. 1:1 layers stack concentrically as a pore-free, onion-like structure. The dynamic processes of dehydration created by slow depressurization of the cell resulted in a decrease in the layer-to-layer distance (d001) from ~10 Å to ~7 Å due to the loss of interlayer water molecules. Irreversible formation of spurious ‘internal pores’ was recorded during this process. These pores were not indigenous to the hydrated 10 Å halloysite and resulted from the collapse of the native layers. They cannot account for the physical chemical properties of spheroidal halloysite. Spheroidal halloysites would have a lower propensity for intercalating ions or molecules than tubular halloysites. Isolated facets were also observed in high-resolution-TEM and displayed a pseudo-hexagonal morphology. The three-dimensional microstructure of the spheroid appeared bent along the three pseudo equivalent yi directions of the kaolinite-like single layers. An analogy with polyhedral serpentine has allowed the proposal of a formation process of hydrated spheroidal halloysite triggered by enrichment in divalent ions in the growth system.
The Illite—Aluminoceladonite Series: Distinguishing Features and Identification Criteria from X-ray Diffraction and Infrared Spectroscopy Data
- Bella B. Zviagina, Victor A. Drits, Jan Środoń, Douglas K. McCarty, Olga V. Dorzhieva
-
- Published online by Cambridge University Press:
- 01 January 2024, pp. 378-394
-
- Article
- Export citation
-
Al-rich K-dioctahedral 1M and 1Md micas are abundant in sedimentary rocks and form a continuous compositional series from (Mg,Fe)-poor illite to aluminoceladonite through Mg-rich illite. The complexity and heterogeneity of chemical composition and structural features, as well as the lack of reliable diagnostic criteria, complicate the identification of these mica varieties. The objectives of the present study were to reveal the structural and crystal-chemical variability in the illite—aluminoceladonite series, and to define the composition ranges and identification criteria for the mica varieties in the series. A collection of illite and aluminoceladonite samples of various compositions was studied by X-ray diffraction (XRD) and Fourier-transform infrared (FTIR) spectroscopy. Analysis of the relationships between unit-cell parameters and cation composition showed that the series includes three groups, (Mg,Fe)-poor illites, Mg-rich illites, and aluminoceladonites, each characterized by a unique combination of unit-cell parameter variation ranges. The distinctive features of aluminoceladonite are reduced values of csinβ and |ccosβ/a| in combination with b parameters that are smaller than those for Mg-rich illites, and slightly greater than those of (Mg,Fe)-poor illites. The compositional boundary between illite and aluminoceladonite occurs at Si = ~3.7 and Mg + Fe2+ = ~ 0.6 atoms per O10(OH)2.
A new approach to the interpretation of the FTIR spectroscopy data involving new relationships between band positons and cation composition of (Mg,Fe)-poor illites, Mg-rich illites, and aluminoceladonites provides additional diagnostic features that include the band positions and profile in the regions of Si—O bending, Si—O stretching, and OH-stretching vibrations. A sharp maximum from the AlOHMg stretching vibration at ~3600 cm−1, the presence of a MgOHMg stretching vibration at 3583–3585 cm−1, as well as characteristic band positions in the Si—O bending (435–, 468–472, and 509–520 cm−1) and stretching regions (985–1012 and 1090–1112 cm−1), are typical of aluminoceladonite.
Transport and Exchange Behavior of Ions in Bentonite During Electro-Osmotic Consolidation
- Hui Wu, Liming Hu, Lin Zhang, Qingbo Wen
-
- Published online by Cambridge University Press:
- 01 January 2024, pp. 395-403
-
- Article
- Export citation
-
Electro-osmotic consolidation is considered to be an efficient technique for dewatering and consolidation of soft soil. In the present study, four experiments were conducted on a Na-rich bentonite using two reactive electrodes (copper and iron) and two inert electrodes (graphite and stainless steel) to study the transport and exchange behavior of ions during electro-osmotic consolidation. The results showed that the changes in pH and ion contents were limited to the zone close to the electrode due to the buffering capacity of bentonite and the significant reduction in electric current density. The ion concentration profiles indicated that Na+ ions were largely responsible for carrying the pore water to the cathode. The reactive electrodes are better at transporting Na+ ions and therefore induce better drainage than inert electrodes. Ion-exchange reactions occurred between the Cu2+ and Fe2+/Fe3+ ions released and pre-existing Na+ ions in the electrical double layer, causing decreased water adsorption capacity and plasticity index. The swelling and shrinkage characteristics of the bentonite were thus reduced, and electroosmotic consolidation may therefore provide a new way to improve the stability of expansive soils and slopes.
Modified Mineral Phases During Clay Ceramic Firing
- M. El Ouahabi, L. Daoudi, F. Hatert, N. Fagel
-
- Published online by Cambridge University Press:
- 01 January 2024, pp. 404-413
-
- Article
- Export citation
-
Ceramic clays are among the most complicated of ceramic systems because of the very intricate relationship between the behavior of minerals during ceramic processing and their modifications during heating. A major challenge is to predict the phase changes in clay ceramics. The aims of this study were to establish reference data of ceramic products that can be formed based on the mineralogical compositions of the local raw materials. These data, in turn, can be compared with archeological ceramics in order to study their origins.
The mineralogical compositions and modifications during firing (550–1100°C under oxidizing conditions) of seven clayey materials sampled from the main clay deposits of northern Morocco were evaluated by X-ray powder diffraction. Two groups of clays were distinguished according to the type of neoformed high-temperature minerals: non-calcareous clays and calcareous clays. For the non-calcareous raw materials, spinel was produced at 950°C. Cristobalite and mullite were formed at temperatures in excess of 1000°C from clays that contain illite, kaolinite, and chlorite. In clays containing vermiculite and large amounts of chlorite, hematite was formed at temperatures in excess of 950°C. Firing of calcareous clays at temperatures >950°C yielded Ca-silicates (diopside, gehlenite and wollastonite), spinel, cristobalite, hematite, and feldspars. Mullite may also form in the calcareous clay products when the carbonate content exceeds 10%.