Skip to main content
    • Aa
    • Aa

Strength and fracture of Si micropillars: A new scanning electron microscopy-based micro-compression test

  • B. Moser (a1), K. Wasmer (a1), L. Barbieri (a2) and J. Michler (a1)

A novel method for in situ scanning electron microscope (SEM) micro-compression tests is presented. The direct SEM observation during the instrumented compression testing allows for very efficient positioning and assessment of the failure mechanism. Compression tests on micromachined Si pillars with volumes down to 2 μm3 are performed inside the SEM, and the results demonstrate the potential of the method. In situ observation shows that small diameter pillars tend to buckle while larger ones tend to crack before failure. Compressive strength increases with decreasing pillar diameter and reaches almost 9 GPa for submicrometer diameter pillars. This result is in agreement with earlier bending experiments on Si. Difficulties associated with precise strain measurements are discussed.

Corresponding author
a) Address all correspondence to this author. e-mail:
Linked references
Hide All

This list contains references from the content that can be linked to their source. For a full set of references and notes please see the PDF or HTML where available.

1O. Kraft and C.A. Volkert : Mechanical testing of thin films and small structures. Adv. Eng. Mater. 3, 99 (2001).

2E. Arzt : Overview No. 130—Size effects in materials due to microstructural and dimensional contraints: A comparative review. Acta Mater. 46, 5611 (1998).

3F. Ericson and J.A. Schweitz : Micromechanical fracture strength of silicon. J. Appl. Phys. 68, 5840 (1990).

4T. Tsuchiya , O. Tabata , J. Sakata , and Y. Taga : Specimen size effect on tensile strength of surface micromachined polycrystalline silicon thin films. J. Microeletromech. S 7, 106113(1998).

6O.M. Jadaan , N.N. Nemeth , J. Bagdahn , and W.N. Sharpe : Probabilistic Weibull behavior and mechanical properties of MEMS brittle materials. J. Mater. Sci. 38, 4087 (2003).

7S. Greek , F. Ericson , S. Johansson , and J.A. Schweitz : In situ tensile strength measurement and Weibull analysis of thick film and thin film micromachined polysilicon structures. Thin Solid Films 292, 247 (1997).

8T. Namazu , Y. Isono , and T. Tanaka : Evaluation of size effect on mechanical properties of single crystal silicon by nanoscale bending test using AFM. J. Microelectromech. Syst. 9, 450 (2000).

10M.D. Uchic , D.M. Dimiduk , J.N. Florando , and W.D. Nix : Sample dimensions influence strength and crystal plasticity. Science 305, 986 (2004).

13H.E. Read and G.A. Hegemier : Strain softening of rock, soil, and concrete—A review article. Mech. Mater. 3, 271 (1984).

14A. Drescher and I. Vardoulakis : Geometric softening in triaxial tests on granular material. Geotechnique 32, 291 (1982).

15I. Vardoulakis , J.F. Labuz , E. Papamichos , and J. Tronvoll : Continuum fracture mechanics of uniaxial compression on brittle materials. Int. J. Solids Struct. 35, 4313 (1998).

17T. Namazu , Y. Isono , and T. Tanaka : Nano-scale bending test of Si beam for MEMS, in Proceedings of the IEEE Thirteenth Annual International Conference on Micro Electro Mechanical Systems (IEEE, Miyazaki, Japan, 2000), pp. 205210.

18A.M. Fitzgerald , R.H. Dauskardt , and T.W. Kenny : Fracture toughness and crack growth phenomena of plasma-etched single crystal silicon. Sens. Actuators A Phys. 83, 194 (2000).

20J.K. Bhardwaj and H. Ashraf : Advanced silicon etching using high density plasmas, in Micromachining and Microfabrication Process Technology edited by K.W. Markus (Proc. SPIE—Int. Soc. Opt. Eng., Austin, TX, 1995), pp. 224233.

22H. Zhang , B.E. Schuster , Q. Wei , and K.T. Ramesh : The design of accurate micro-compression experiments. Scripta Mater. 54, 181 (2006).

Recommend this journal

Email your librarian or administrator to recommend adding this journal to your organisation's collection.

Journal of Materials Research
  • ISSN: 0884-2914
  • EISSN: 2044-5326
  • URL: /core/journals/journal-of-materials-research
Please enter your name
Please enter a valid email address
Who would you like to send this to? *