Hostname: page-component-8448b6f56d-xtgtn Total loading time: 0 Render date: 2024-04-16T15:57:42.790Z Has data issue: false hasContentIssue false
  • English
  • Français

Isothermal Stress Relaxation In Al, AlCu and AlVPd Films

Published online by Cambridge University Press:  15 February 2011

J. P. Lokker ,
J. F. Jongste ,
G. C. A. M. Janssen  and
S. Radelaar
J. P. Lokker
Affiliation:
DIMES, Delft University of Technology, P.O. Box 5046, 2600 GA Delft, The NetherlandsLokker @ Dimes.tudelft.nl
J. F. Jongste
Affiliation:
DIMES, Delft University of Technology, P.O. Box 5046, 2600 GA Delft, The NetherlandsLokker @ Dimes.tudelft.nl
G. C. A. M. Janssen
Affiliation:
DIMES, Delft University of Technology, P.O. Box 5046, 2600 GA Delft, The NetherlandsLokker @ Dimes.tudelft.nl
S. Radelaar
Affiliation:
DIMES, Delft University of Technology, P.O. Box 5046, 2600 GA Delft, The NetherlandsLokker @ Dimes.tudelft.nl
Get access

Abstract

Mechanical stress and its relaxation in aluminum metallization in integrated circuits (IC) are a major concern for the reliability of the material. It is known that adding Cu improves the reliability but complicates plasma etching and increases corrosion sensitivity. The mechanical behavior of AIVPd, AlCu and Al blanket films is investigated by wafer curvature measurements. During thermal cycling between 50°C and 400°C the highest tensile stress is found in AIVPd. In a subsequent experiment, the cooling was interrupted at several temperatures to investigate the stress behavior during an eight hour isothermal treatment. Isothermal stress relaxation has been observed in the three types of films and is discussed.

Type
Research Article
Information
MRS Online Proceedings Library (OPL) , Volume 428: Symposium L – Materials Reliability in Microelectronics VI , 1996 , 513
Copyright
Copyright © Materials Research Society 1996

Access options

Get access to the full version of this content by using one of the access options below. (Log in options will check for institutional or personal access. Content may require purchase if you do not have access.)

References

1 Nix, W.D., Metallurgical Transactions A, 20A, 2217 (1989)Google Scholar
2 Volkert, C.A., Alofs, C.F., Liefting, J.R., J. Mater. Res., 9, 1147 (1994)Google Scholar
3 Frost, H.J., in Materials Reliability in Microelectronics If eds. Thompson, C.V. and Lloyd, J.R., Mater. Res. Symp. Proc. 264, 3 (1992)Google Scholar
4 R.W., Hoffman, in Physics of Thin Films, edited by Haas, G. and Thun, R.E., (Academic, New York, 1966), 3, 222 Google Scholar
5 Venkatraman, R., Besser, P.R., Bravman, J.C., J. Mater. Res., 9, 328 (1994)Google Scholar
6 Witvrouw, A., Proost, J., Deweerdt, B., Roussel, Ph, Maex, K., Mater. Res. Soc. Symp.Proc., 356, 441 (1995)Google Scholar
7 Haasen, P., in Physical Metallurgy (Cambridge University Press, London 1978) p. 201 Google Scholar
8 Flinn, P.A., Gardner, D.S., Nix, W.D., IEEE Trans. on El. Dev., 34, 689 (1987)Google Scholar