Hostname: page-component-8448b6f56d-c4f8m Total loading time: 0 Render date: 2024-04-19T07:15:21.929Z Has data issue: false hasContentIssue false
  • English
  • Français

Microstructural and Mechanical Properties of Boron Carbide Ceramics by Methanol Washed Powder

Published online by Cambridge University Press:  31 January 2011

Jong Pil Ahn ,
Kyoung Hun Kim ,
Joo Seok Park ,
Jae Hong Chae ,
Sung Min So  and
Hyung Sun Kim
Jong Pil Ahn
Affiliation:
khkim@kicet.re.kr, Korea Institute of Ceramic Engineering and Technology, Seoul, Korea, Republic of
Kyoung Hun Kim
Affiliation:
jpjam@naver.com, Korea Institute of Ceramic Engineering and Technology, Seoul, Korea, Republic of
Joo Seok Park
Affiliation:
pjuju@kicet.re.kr, Korea Institute of Ceramic Engineering and Technology, Seoul, Korea, Republic of
Jae Hong Chae
Affiliation:
jhchae@kicet.re.kr, Korea Institute of Ceramic Engineering and Technology, Seoul, Korea, Republic of
Sung Min So
Affiliation:
stomssm@yahoo.co.kr, Korea Institute of Ceramic Engineering and Technology, Seoul, Korea, Republic of
Hyung Sun Kim
Affiliation:
kimhs@inha.ac.kr, Inha University, Materials Engineering, Incheon, Korea, Republic of
Get access

Abstract

Boron carbide (B4C) is currently used in lightweight armors and high temperature materials, because it has high meting point, good hardness, low specific gravity and good mechanical properties. The sintering of boron carbide, however, is restricted by its high covalent bonding and B2O3 coatings on B4C particles surface which can cause a microstructural coarsening during sintering. Therefore, it is necessary to remove B2O3 film of By4C particles surface to restrict microstructural coarsening and densification of B4C. B4C ceramics were fabricated by a hot-press sintering and its sintering behavior, microstructure and mechanical properties were evaluated. The relative density of B4C ceramics were obtained by a hot-press sintering reached as high as 99% without any sintering additives. The mechanical properties of B4C ceramics was improved by a methanol washing which can remove B2O3 phase from a B4C powder surface. This improvement is resulted from the formation of homogeneous microstructure because the grain coarsening was suppressed by the elimination of B2O3 phase. Particularly, the mechanical properties of the sintered samples using a methanol washed powder improved compared with the samples using an as-received commercial powder.

Keywords

ceramichot pressingsintering
Type
Research Article
Information
MRS Online Proceedings Library (OPL) , Volume 1224: Symposia FF/GG – Mechanical Behavior at Small Scales — Experiments and Modeling , 2009 , 1224-FF10-35
Copyright
Copyright © Materials Research Society 2010

Access options

Get access to the full version of this content by using one of the access options below. (Log in options will check for institutional or personal access. Content may require purchase if you do not have access.)

References

1 Thevenot, F., Euro, J.. Ceram. Soc. 6[4] (1990) 205–225.Google Scholar
2 Simeone, D., Mallet, C., Dubuisson, P., Baldinozzi, G., Gervais, C., and maquet, J., J. Nucl. Mater. 277 (2000) 1–10.Google Scholar
3 Beauvy, J., J. Less Common Metals 90[2] (1983) 169–175.Google Scholar
4 Allen, R. D., J. Am. Chem. Soc. 75[14] (1953) 3582–3583.Google Scholar
5 Niihara, K., Nakahira, A., and Hirai, T., J. Am. Ceram. Soc. 67[1] (1984) c13–c14.Google Scholar
6 Williams, P. D., and Hawn, D. D., J. Am. Ceram. Soc. 74[7] (1991) 1614–1618.Google Scholar
7 Dole, S. L., Prochazka, S., and Doremus, R. H., J. Am. Ceram. Soc. 72[6] (1989) 958–966.Google Scholar