Hostname: page-component-8448b6f56d-wq2xx Total loading time: 0 Render date: 2024-04-24T08:00:46.399Z Has data issue: false hasContentIssue false
  • English
  • Français

The Role of Indentation Depth on the Measured Hardness of Materials

Published online by Cambridge University Press:  15 February 2011

Melissa Shell De Guzman ,
Gabi Neubauer ,
Paul Flinn  and
William D. Nix
Melissa Shell De Guzman
Affiliation:
Intel Corporation, P.O. Box 58119, MS: SC2-24, 2200 Mission College Blvd., Santa Clara, CA 95052-8119
Gabi Neubauer
Affiliation:
Intel Corporation, P.O. Box 58119, MS: SC2-24, 2200 Mission College Blvd., Santa Clara, CA 95052-8119
Paul Flinn
Affiliation:
Intel Corporation, P.O. Box 58119, MS: SC2-24, 2200 Mission College Blvd., Santa Clara, CA 95052-8119
William D. Nix
Affiliation:
Stanford University, Department of Materials Science and Engineering, Bldg 550, Peterson Lab, Stanford CA 94305-2205
Get access

Abstract

Ultra micro-indentation tests on Ni and Cu samples showed increasing hardness with decreasing penetration depth over a range from 200 to 2000 nm. The results suggest increased strain hardening with decreased indentation depth. To establish that this is a real material effect, a series of tests were conducted on amorphous materials, for which strain hardening is not expected. The hardness of Metglas® was found to be independent of depth. A simple model of the dislocation densities produced under the indenter tip describes the data well. The model is based on the fact that the high density of dislocations expected under a shallow indentation would cause an increase in measured hardness. At large depths, the density of geometrically necessary dislocations is sufficiently small to have little effect on hardness, and the measured hardness approaches the intrinsic hardness of the material.

Type
Research Article
Information
MRS Online Proceedings Library (OPL) , Volume 308: Symposium M1 – Thin Films: Stresses and Mechanical Properties IV , 1993 , 613
Copyright
Copyright © Materials Research Society 1993

Access options

Get access to the full version of this content by using one of the access options below. (Log in options will check for institutional or personal access. Content may require purchase if you do not have access.)

References

REFERENCES

1 Burnett, P.J. and Rickerby, D.S., Thin Solid Films 148, 51 (1987).CrossRefGoogle Scholar
2 Bhushan, B., Williams, V.S., and Shack, R.V., J. Tribology 110, 563 (1988)CrossRefGoogle Scholar
3 Upit, G.P. and Varchenya, S.A., in The Science of Hardness Testing and its Research Applications, edited by Westbrook, J.H. and Conrad, H. (American Society for Metals, 1971) pp. 135–146.Google Scholar
4 Stelmashenko, N.A., Walls, M.G., Brown, L.M., and Milman, Y.V., in Mechanical Properties and Deformation Behaviorof Materials Having Ultra-Fine Microstructures. edited by Nastasi, M., Parkin, D.M. and Gleiter, H. (NATO ASI Series E 233,1993) pp. 605–610.CrossRefGoogle Scholar
5 Taylor, G.I., Proc. Roy. Soc. (London), A145, 362 (1934).Google Scholar
6 Cottrell, A.H., in An Introduction to Metallurgy. (Edward Arnold Publishers Ltd., London 1967), p. 434.Google Scholar
7 Bowden, F.P. and Tabor, D., in The Friction and Lubrication of Solids. (Clarendon Press, Oxford, 1986), p. 12.Google Scholar
8 Doerner, M.F. and Nix, W.D., J. Mater. Res. 6, 601 (1986).CrossRefGoogle Scholar
9 Oliver, W.C. and Pharr, G.M., J. Mater. Res. 7,1564 (1992).CrossRefGoogle Scholar