Hostname: page-component-7c8c6479df-fqc5m Total loading time: 0 Render date: 2024-03-28T16:05:28.448Z Has data issue: false hasContentIssue false

“Reverse” Stress Relaxation in cu Thin Films

Published online by Cambridge University Press:  18 March 2011

R. Spolenak
Affiliation:
Agere Systems, formerly of Bell Laboratories, Lucent Technologies, Murray Hill, NJ 07974, USA
C. A. Volkert
Affiliation:
Max-Planck-Institut für Metallforschung, Stuttgart, Germany
S. Ziegler
Affiliation:
Agere Systems, formerly of Bell Laboratories, Lucent Technologies, Murray Hill, NJ 07974, USA I. Physik. Inst. A., Lehrstuhl für Physik neuer Materialien, Aachen, Germany
C. Panofen
Affiliation:
Agere Systems, formerly of Bell Laboratories, Lucent Technologies, Murray Hill, NJ 07974, USA I. Physik. Inst. A., Lehrstuhl für Physik neuer Materialien, Aachen, Germany
W.L. Brown
Affiliation:
Agere Systems, formerly of Bell Laboratories, Lucent Technologies, Murray Hill, NJ 07974, USA
Get access

Abstract

In this study we present investigation on the anelastic behavior of sputtered 1 [.proportional]m thin Cu films. Most of the literature that reports on the mechanical properties of thin metallic films is based on substrate curvature measurements. We have developed a new version of a bulge tester that combines the capacitive measurement of the bulge deflection of a membrane with a resonance frequency measurement of the residual stress in the membrane. A Cu membrane is plastically deformed to a pre-determined strain by controlled gas-pressure bulging of the membrane. After the bulging stress is removed, the residual tensile stress, which has been decreased by the plastic deformation, is then determined by measuring the resonant frequency as a function of time. Immediately after plastic straining, the residual (tensile) stress of membranes was observed to increase. At room temperature a maximum stress was typically reached in the order of an hour. At still longer times the stress decreased again as a result of creep. The transient increase in stress following plastic straining grew larger as the amount of plastic strain produced by bulging was increased. With higher temperatures the transient became both faster and larger. A model is presented that based on the mechanism of thermally activated glide separates the microstructure in a class of “soft” and “hard” grains solving the issue of an “apparent” increase in strain energy as a function of time after deformation.

Type
Research Article
Copyright
Copyright © Materials Research Society 2001

Access options

Get access to the full version of this content by using one of the access options below. (Log in options will check for institutional or personal access. Content may require purchase if you do not have access.)

References

REFERENCES

1. Vinci, R. P., Cornella, G., and Bravman, J. C., AIP Conf. Proc. 491, 240248 (1999).Google Scholar
2. Kalkman, A. J., Verbruggen, A. H., Janssen, G. C. A. M., and Groen, F. H., Rev. of. Sci. Inst. 70(10), 40264031, (1999).Google Scholar
3. Vlassak, J., and Nix, W. D., J. Mater. Res. 7, 1553 (1992).Google Scholar
4. Spolenak, R., Ziegler, S., Volkert, C. A., Boie, B., Kraus, J., Kossives, D., and Brown, W. L., in preparation (2001).Google Scholar
5. Schlax, M. P., Engelstad, R. L., Lovell, E. G., Liddle;, J. A. and Novembre, A. E., Proc. of the SPIE, 3676, 152161 (1999).Google Scholar
6. Schlax, M. P., Engelstad, R. L., Lovell, E. G., Liddle;, J. A. and Novembre, A. E., J. of Vac. Sci. & Tech. B, 17(6), 2714–18 (1999).Google Scholar
7. Cottrell, A.H., “Dislocations and Plastic Flow in Crystals”, Oxford University Press, London (1953)Google Scholar
8. Frost, H. J. and Ashby, M. F., “Deformation mechanism maps”, Pergamon Press, Oxford (1982).Google Scholar
9. Flinn, P. A., Gardner, D. S., and Nix, W. D., IEEE Trans. Electr. Dev., ED–34(3), 689–99Google Scholar
10. Thouless, M. D., Rodbell, K. P., and Cabral, C. J., J. Vac. Sci. Tech. A, 14(4), 2454–61Google Scholar
11. Weiss, D., O Kraft, and Arzt, E., Mat. Soc. Rec. Proc. 562, 257262 (1999).Google Scholar
12. Kobrinsky, M. J., and Thompson, C. V., Acta mater. 48, 625633 (2000).Google Scholar
13. Spolenak, R., Tamura, N., Valek, B., MacDowell, A.A., Celestre, R.S., Brown, W.L., Bravman, J.C., Padmore, H.A., Marieb, T., Batterman, B.W., and Patel, J.R., in preparation, presented at MRS Fall Meeting 2000, Boston.Google Scholar