Hostname: page-component-7c8c6479df-r7xzm Total loading time: 0 Render date: 2024-03-28T12:43:22.653Z Has data issue: false hasContentIssue false

Characterization Of SnO2 Nanoparticles Deposited Via Layer-by-Layer Self Assembly And Investigation Of Their Sensing Properties

Published online by Cambridge University Press:  11 February 2011

R. C. Ghan
Affiliation:
Louisiana Tech University, Institute for Micromanufacturing, 911 Hergot Avenue, P.O. Box 10137, Ruston, LA, 71270. Fax: (240) 255–4028 Email: rbesser@coes.latech.edu
Y. Lvov
Affiliation:
Louisiana Tech University, Institute for Micromanufacturing, 911 Hergot Avenue, P.O. Box 10137, Ruston, LA, 71270. Fax: (240) 255–4028 Email: rbesser@coes.latech.edu
R. S. Besser
Affiliation:
Louisiana Tech University, Institute for Micromanufacturing, 911 Hergot Avenue, P.O. Box 10137, Ruston, LA, 71270. Fax: (240) 255–4028 Email: rbesser@coes.latech.edu
Get access

Abstract

A technique of Layer-by-Layer (LbL) self-assembly is used to deposit SnO2 nanoparticles on Quartz Crystal Microbalance (QCM) resonators, and on glass substrates which the authors believe has not been previously reported. Characterization of self-assembled SnO2 layers has been performed using QCM, Scanning Electron Microscopy (SEM), and Zeta Potential analysis.

We have successfully deposited SnO2 nanoparticles on QCM resonator using self-assembly technique. LbL self-assembly is a method of organization of ultra-thin films by interlayer electrostatic attraction. The thickness and mass of the self-assembled layers can be characterized by the frequency shift obtained using the QCM and empirical equations relating change in frequency with mass and thickness of deposited layers. The deposition of SnO2 nanolayers exhibited a linear reproducibility and the process of self-assembly was independent of the residence time of QCM resonator in the SnO2 nanoparticle colloidal solution. High resolution SEM analysis reveals that the SnO2 nanoparticle layers are uniformly deposited across the entire substrate. Electrical characterization was performed on SnO2 nanoparticle layers self-assembled on glass substrates which were patterned for two point (current-voltage) IV characteristic measurements. Two classes of samples were used. One sample was self-assembled glass substrate patterned with electrical contacts and calcined (baked at 350°C for one hour) to eliminate interlayered polyions and the other sample was not calcined. Results revealed that the calcined samples demonstrated linear ohmic behavior but the uncalcined showed some spurious points which we believe are due to the polyion layers.

Characterization of the self-assembled SnO2 nanoparticles is being carried out with the intention of fabricating a high-selectivity μ-gas sensor. A test chamber has been fabricated and results of resistance behavior of the sensor with variation in temperature have been presented.

The sensor can find applications in high selectivity sensing of chemical, industrial, domestic, and hazardous environments. After further research and development, this μ-gas sensors could be made generic to sense a variety of gases and employed for integrated on-chip product analysis in multiple chemical microsystem applications.

Type
Research Article
Copyright
Copyright © Materials Research Society 2003

Access options

Get access to the full version of this content by using one of the access options below. (Log in options will check for institutional or personal access. Content may require purchase if you do not have access.)

References

REFERENCES

1. Sberveglieri, G. et.al, Sensors and Actuators, B 77, 16, (2001).Google Scholar
2. Passacantando, M. et.al, Sensors and Actuators, B 4206, 1, (2001).Google Scholar
3. Selfert, R. et.al, Sensors and Actuators, B 81, 301, (2002).Google Scholar
4. Sears, W.M. et.al, Sensors and Actuators, 19, 333, (1989).Google Scholar
5. Matsuo, K. et.al., Magasaki Daigaku Kogakubu Kenkyu Hokoku, 17, 67, (1987).Google Scholar
6. Hoffheins, B. in Chemical and Biological Sensors, 2nd edited Taylor, R.F, Schultz, J.S, (IOP publishing Ltd.) p. 371 Google Scholar
7. Kunitake, T., Lvov, Y. et.al, Langmuir, 14, 187, (1998).Google Scholar
8. Chaudret, B. et.al, Sensors and Actuators, B 78, 83, (2001)Google Scholar
9. Ihokura, K., Watson, J. in Stannic Oxide Gas Sensor, (CRC press Inc.) p. 1 Google Scholar
10. Pachpakesan, B. et.al, Sensors and Actuators, B 77, 145, (2001).Google Scholar
11. Semancik, S. et.al, Sensors and Actuators, B 77, 167, (2001).Google Scholar
12. Morante, J. et.al, Sensors and Actuators, B 78, 57, (2001).Google Scholar
13. Kim, K., Sensors and Actuators, B77, 427, (2001).Google Scholar
14. Lee, D.D. et.al, Sensors and Actuators, B 77, 90, (2001).Google Scholar
15. Ostrander, J.W.; Mamedov, A.A.; Kotov, N.A. J. Am. Chem. Soc., 123, 1101, (2001)Google Scholar
16. Ghan, R.C., Lvov, Y., Besser, R.S. in Nanophase and Nanocomposite Materials IV edited by Komarneni, S., Vaia, R.A., Lu, G.Q., Matsushita, J-I., Parker, J.C. (Mater. Res. Soc. Proc. V 703, 2001).Google Scholar
17. Prevot, M., Ghan, R., Lvov, Y., and Besser, R.S., “The Integration of Silicon Micromachining and Layer-by-Layer Nanoassembly,” Abstracts of the Tex-MEMS III Conference, University of Texas and Zyvex Corporation, 2001.Google Scholar
18. Sukhorukov, G.B., Möhwald, H., Decher, G., Lvov, Yu.M., Thin Solid Films, 284/285, 223, (1996)Google Scholar
19. Yoo, D., Lee, J.K., Rubner, M.F., Mat. Res. Soc. Symp. Proc, 413, p. 395, (1996)Google Scholar
20. Kim, G., Farris, R.J., McCarthy, T.J., Polym. Prepr. Am. Chem. Soc. Polym. Chem. Div., 38 (2), 672, (1997)Google Scholar
21. Wang, M.T., Zhang, L.D., J. Mater. Res., 16(3), 765, (2001)Google Scholar
22. Kim, D.W., Blumstein, A., Kumar, J., Tripathy, S.K., Chem. Mater., 13, 246, (2001)Google Scholar
23. Cutnell, J., Johnson, K. in Elementary Physics, 5th edition, 595, (2001).Google Scholar
24. Dermody, D.L., Peez, R.F., Bergbreiter, D.E., Crooks, R.M., Langmuir, 15, 890, (1999)Google Scholar
25. Lvov, Y., Ariga, K., Onda, M., Ichinose, I., Kunitake, T., Coll. Surf. A, 146, 346, (1999)Google Scholar
26. Morante, J.R. et. al, Sensors and Actuators, B 4210, 1, (2002)Google Scholar