We predict the production yield of a medical radioisotope ${}^{67}$Cu using ${}^{67}$Zn(n, p)${}^{67}$Cu and ${}^{68}$Zn(n, pn)${}^{67}$Cu reactions with fast neutrons provided from laser-driven neutron sources. The neutrons were generated by the p+${}^9\mathrm{Be}$ and d+${}^9$Be reactions with high-energy ions accelerated by laser–plasma interaction. We evaluated the yield to be (3.3 $\pm$ 0.5) $\times$ 10${}^5$ atoms for ${}^{67}$Cu, corresponding to a radioactivity of 1.0 $\pm$ 0.2 Bq, for a Zn foil sample with a single laser shot. Using a simulation with this result, we estimated ${}^{67}$Cu production with a high-frequency laser. The result suggests that it is possible to generate ${}^{67}$Cu with a radioactivity of 270 MBq using a future laser system with a frequency of 10 Hz and 10,000-s radiation in a hospital.

In this study, we experimentally evaluate the ion transportation through a cone guide target, which accelerates ions up to MeV energies via target normal sheath acceleration, and transports them onto the position of imploding fuel in the fast ignition scenario of nuclear fusion. We measured the electric and magnetic fields (EM-fields) induced by return current streaming along the cone wall by proton radiography, and we report that the EM-fields are predominantly induced within a temporal window up to 30 ps after the laser injection. The magnitude of the electric field is maximized around 13 ps, reaching $4.0\times 10^{10} \mathrm {V}\ \mathrm {m}^{-1}$, when the magnetic field is below 200 T. The present scheme provides insights on the EM-fields evaluation in the time region that is difficult to treat with simulations due to the computing resources.

Resorcinol/formaldehyde (RF) foam resin is an attractive material as a low-density target in high-power laser–plasma experiments because of its fine network structure, transparency in the visible region, and low-Z element (hydrogen, carbon, and oxygen) composition. In this study, we developed disk-shaped RF foam and deuterated RF foam targets with 40–200 μm thickness and approximately 100 mg/cm3 density having a network structure from 100 nm to a few micrometers cell size. By deuteration, the polymerization rate was drastically slowed down owing to kinetic isotope effects. These targets were used in high-power laser experiments where a megaelectronvolt proton beam was successfully generated.

We characterize the electron density distributions of preformed plasma for laser-accelerated proton generation. The preformed plasma of a titanium target 3 μm thick is generated by prepulse and amplified spontaneous emission (ASE) of a high-intensity Ti:sapphire laser and is measured with an interferometer using a second harmonic probe beam. High-energy protons are obtained by reducing the size of the preformed plasma by changing the ASE duration before main pulse at the front side (laser incidence side) of the target. Simulation results with two-dimensional radiation hydrodynamic code are close to the experimental results for low-density region ~4 × 1019 cm−3 at the front side. In the high-density region near to the target surface, the interferometry underestimates the density due to the substantial refraction. The characterization of hydrodynamic expansion with the interferometer and simulation is a useful tool for investigation of high-energy proton generation.

We observed a preformed plasma of an aluminum slab target produced by a high-intensity Ti:sapphire laser. The expansion length of the preformed plasma at the electron density of 3 × 1018 cm−3, which was the detection limit, was around 100 μm measured with a laser interferometer. In order to characterize quantitatively and to control the preformed plasmas, we perform a two-dimensional hydrodynamic simulation. The expansion length of the preformed plasma was almost the same as the experimental result, if we assumed that the amplified spontaneous emission lasted 3.5 ns before the main pulse arrived.