We discuss present and developing techniques for studying radiocarbon in marine organic carbon (C). Bulk DOC (dissolved organic C) Δ14C measurements reveal information about the cycling time and sources of DOC in the ocean, yet they are time consuming and need to be streamlined. To further elucidate the cycling of DOC, various fractions have been separated from bulk DOC, through solid phase extraction of DOC, and ultrafiltration of high and low molecular weight DOC. Research using 14C of DOC and particulate organic C separated into organic fractions revealed that the acid insoluble fraction is similar in 14C signature to that of the lipid fraction. Plans for utilizing this methodology are described. Studies using compound specific radiocarbon analyses to study the origin of biomarkers in the marine environment are reviewed and plans for the future are outlined. Development of ramped pyrolysis oxidation methods are discussed and scientific questions addressed. A modified elemental analysis (EA) combustion reactor is described that allows high particulate organic C sample throughput by direct coupling with the MIniCArbonDAtingSystem.

The first ultraviolet photochemical oxidation (UVox) extraction method for marine dissolved organic carbon (DOC) as CO2 gas was established by Armstrong and co-workers in 1966. Subsequent refinement of the UVox technique has co-evolved with the need for high-precision isotopic (Δ14C, δ13C) analysis and smaller sample size requirements for accelerator mass spectrometry radiocarbon (AMS 14C) measurements. The UVox line at UC Irvine was established in 2004 and the system reaction kinetics and efficiency for isolating seawater DOC rigorously tested for quantitative isolation of ∼1 mg C for AMS 14C measurements. Since then, improvements have been made to sampling, storage, and UVox methods to increase overall efficiency. We discuss our progress, and key UVox system parameters for optimizing precision, accuracy, and efficiency, including (1) ocean to reactor: filtration, storage and preparation of DOC samples, (2) cryogenic trap design, efficiency and quantification of CO2 break through, and (3) use of isotopic standards, blanks and small sample graphitization techniques for the correction of DOC concentrations and Fm values with propagated uncertainties. New DOC UVox systems are in use at many institutions. However, rigorous assessment of quantitative UVox DOC yields and blank contributions, DOC concentrations and carbon isotopic values need to be made. We highlight the need for a community-wide inter-comparison study.

We report marine dissolved organic carbon (DOC) ∆14C from seawater collected from the North central Pacific Ocean (NCP) in 2015. These measurements show DOC ∆14C values averaged –235±5‰ (n=3) in the mixed layer (24–81 m) and –544±5‰ (n=5) in the deep water (1500–5139 m). A comparison of these data with two previously published DOC ∆14C profiles from the NCP in 1985 and 1987 reveals that deep DOC ∆14C values have decreased. We discuss several possible mechanisms that could cause such a shift in DOC ∆14C values, including spatial inhomogeneity and temporal variability due to changes in the dissolution and ∆14C value of surface derived particles in the deep sea. We find that forthcoming profiles of DOC ∆14C results from the NCP will determine the primary mechanisms controlling deep DOC ∆14C distributions, and changes over the past three decades.

The standard procedure for storing/preserving seawater dissolved organic carbon (DOC) samples after field collection is by freezing (–20°C) until future analysis can be made. However, shipping and receiving large numbers of these samples without thawing presents a significant logistical problem and large monetary expense. Access to freezers can also be limited in remote field locations. We therefore test an alternative method of preserving and storing samples for the measurement of DOC concentrations ([DOC]), stable carbon (δ13C), and radiocarbon (as ∆14C) isotopic values via UV photooxidation (UVox). We report a total analytical reproducibility of frozen DOC samples to be [DOC]±1.3 µM, ∆14C±9.4‰, and δ13C±0.1‰, comparable to previously reported results (Druffel et al. 2013). Open Ocean DOC frozen versus acidified duplicates were on average offset by ∆DOC±1.1 µM, ∆∆14C± –1.3‰, and ∆δ13C± –0.1‰. Coastal Ocean frozen vs. acidified sample replicates, collected as part of a long-term (380-day) storage experiment, had larger, albeit consistent offsets of ∆DOC±2.2 µM, ∆∆14C±1.5‰, and ∆δ13C± –0.2‰. A simple isotopic mass balance of changes in [DOC], ∆14C, and δ13C values reveals loss of semi-labile DOC (2.2±0.6 µM, ∆14C=–94±105‰, δ13C=–27±10‰; n=4) and semi-recalcitrant DOC (2.4±0.7 µM, ∆14C=–478±116‰, δ13C=–23.4±3.0‰; n=3) in Coastal and Open Ocean acidified samples, respectively.

We report results of duplicate measurements of dissolved organic carbon concentrations ([DOC] as μM) and Δ14C in seawater in order to assess the total uncertainty of reported [DOC] and Δ14C measurements via the UV oxidation method. In addition, pure International Atomic Energy Agency standards analyzed over a 4-yr period are evaluated. We find the total uncertainty of Δ14C measurements to be ±4.0. However, in samples that were thawed, subsampled, and refrozen prior to UV oxidation, the total uncertainty of Δ14C measurements is on the order of ±10. The [DOC] measurements of these samples were also higher by 1.8 ± 0.3 μM. The reason(s) for these documented increases in total [DOC] and Δ14C uncertainty are unclear. In order to minimize any effects on sample measurements, we recommend the following: 1) regular monitoring of duplicate samples, DOC standards, and diluent (Milli-Q™) water for Δ14C and [DOC] measurements; 2) thawing a sample immediately and only once prior to UV oxidation; 3) avoid the use of DOC-leachable plumbing (such as PVC pipe) in both water systems feeding and within Milli-Q systems; and 4) consider the use of DOC-free diluents (i.e. pre-UV oxidized Milli-Q or sample water).

State-of-the-art ICs for microprocessors routinely dissipate power densitieson the order of 50 W/cm2. This large power is due to thelocalized heating of ICs operating at high frequencies, and must be managedfor future high-frequency microelectronic applications. Our approachinvolves finding new and efficient thermally conductive materials.Exploiting carbon nanotube (CNT) films and composites for their superioraxial thermal conductance properties has the potential for such anapplication requiring efficient heat transfer. In this work, we presentthermal contact resistance measurement results for CNT and CNT-Cu compositefilms. It is shown that Cu-filled CNT arrays enhance thermal conductancewhen compared to as-grown CNT arrays. Furthermore, the CNT-Cu compositematerial provides a mechanically robust alternative to current IC packagingtechnology.