Tiafenacil is a new nonselective protoporphyrinogen IX oxidase (PPO)–inhibiting herbicide with both grass and broadleaf activity labeled for preplant application to corn, cotton, soybean, and wheat. Early-season corn emergence and growth often coincides in the mid-South with preplant herbicide application in cotton and soybean, thereby increasing opportunity for off-target herbicide movement from adjacent fields. Field studies were conducted in 2022 to identify the impacts of reduced rates of tiafenacil (12.5% to 0.4% of the lowest labeled application rate of 24.64 g ai ha–1) applied to two- or four-leaf corn. Corn injury 1 wk after treatment (WAT) for the two- and four-leaf growth stages ranged from 31% to 6% and 37% to 9%, respectively, whereas at 2 WAT these respective ranges were 21.7% to 4% and 22.5% to 7.2%. By 4 WAT, visible injury following the two- and four-leaf exposure timing was no greater than 8% in all instances except the highest tiafenacil rate applied at the four-leaf growth stage (13%). Tiafenacil had no negative season-long impact, as the early-season injury observed was not manifested in a reduction in corn height 2 WAT or yield. Application of tiafenacil directly adjacent to corn in early vegetative stages of growth should be avoided. In cases where off-target movement does occur, however, affected corn should be expected to fully recover with no impact on growth and yield, assuming adequate growing conditions and agronomic/pest management practices are provided.

Tiafenacil is a new non-selective protoporphyrinogen IX oxidase (PPO)-inhibiting herbicide with both grass and broadleaf activity labeled for preplant application to corn (Zea mays L.), cotton (Gossypium hirsutum L.), soybean [Glycine max (L.) Merr.], and wheat (Triticum aestivum L.). Early-season soybean emergence and growth often coincide in the U.S. Midsouth with preplant herbicide application in later-planted cotton and soybean, thereby increasing opportunity for off-target herbicide movement from adjacent fields. Field studies were conducted in 2022 to identify any deleterious impacts of reduced rates of tiafenacil (12.5% to 0.4% of the lowest labeled application rate of 24.64 g ai ha−1) applied to 1- to 2-leaf soybean. Visual injury at 1 wk after treatment (WAT) with 1/8×, 1/16×, 1/32×, and 1/64× rate of tiafenacil was 80%, 61%, 39%, and 21%, while at 4 WAT, these respective rates resulted in visual injury of 67%, 33%, 14%, and 4%. Tiafenacil at these respective rates reduced soybean height 55% to 2% and 53% to 5% at 1 and 4 WAT and soybean yield 53%, 24%, 5%, and 1%. Application of tiafenacil directly adjacent to soybean in early vegetative growth should be avoided, as severe visual injury will occur. In cases where off-target movement does occur, impacted soybean should not be expected to fully recover, and negative impact on growth and yield will be observed.

Microscopy is a widely used method in biological research to observe the morphology and structure of cells. Amongst the plethora of microscopy techniques, fluorescent labeling with dyes or antibodies is the most popular method for revealing specific cellular organelles. However, fluorescent labeling also introduces new challenges to cellular observation, as it increases the workload, and the process may result in nonspecific labeling. Recent advances in deep visual learning have shown that there are systematic relationships between fluorescent and bright-field images, thus facilitating image translation between the two. In this article, we propose the cross-attention conditional generative adversarial network (XAcGAN) model. It employs state-of-the-art GANs (GANs) to solve the image translation task. The model uses supervised learning and combines attention-based networks to explore spatial information during translation. In addition, we demonstrate the successful application of XAcGAN to infer the health state of translated nuclei from bright-field microscopy images. The results show that our approach achieves excellent performance both in terms of image translation and nuclei state inference.

Avian influenza (AI) is an important disease that has significant implications for animal and human health. High pathogenicity AI (HPAI) has emerged in consecutive seasons within the UK to cause the largest outbreaks recorded. Statutory measures to control outbreaks of AI virus (AIV) at poultry farms involve disposal of all birds on infected premises. Understanding of the timing of incursions into the UK could facilitate decisions on improved responses. During the autumnal migration and wintering period (autumn 2019– spring 2020), three active sampling approaches were trialled for wild bird species considered likely to be involved in captive AI outbreaks with retrospective laboratory testing undertaken to define the presence of AIV.

Faecal sampling of birds (n = 594) caught during routine and responsive mist net sampling failed to detect AIV. Cloacal sampling of hunter-harvested waterfowl (n = 146) detected seven positive samples from three species with the earliest detection on the 17 October 2020. Statutory sampling first detected AIV in wild and captive birds on 3 November 2020. We conclude that hunter sourced sampling of waterfowl presents an opportunity to detect AI within the UK in advance of outbreaks on poultry farms and allow for early intervention measures to protect the national poultry flock.

Acifluorfen is a nonsystemic PPO-inhibiting herbicide commonly used for POST Palmer amaranth control in soybean, peanut, and rice across the southern United States. Concerns have been raised regarding herbicide selection pressure and particle drift, increasing the need for application practices that optimize herbicide efficacy while mitigating spray drift. Field research was conducted in 2016, 2017, and 2018 in Mississippi and Nebraska to evaluate the influence of a range of spray droplet sizes [150 μm (Fine) to 900 μm (Ultra Coarse)], using acifluorfen to create a novel Palmer amaranth management recommendation using pulse width modulation (PWM) technology. A pooled site-year generalized additive model (GAM) analysis suggested that 150-μm (Fine) droplets should be used to obtain the greatest Palmer amaranth control and dry biomass reduction. Nevertheless, GAM models indicated that only 7.2% of the variability observed in Palmer amaranth control was due to differences in spray droplet size. Therefore, location-specific GAM analyses were performed to account for geographical differences to increase the accuracy of prediction models. GAM models suggested that 250-μm (Medium) droplets optimize acifluorfen efficacy on Palmer amaranth in Dundee, MS, and 310-μm (Medium) droplets could sustain 90% of maximum weed control. Specific models for Beaver City, NE, indicated that 150-μm (Fine) droplets provide maximum Palmer amaranth control, and 340-μm (Medium) droplets could maintain 90% of greatest weed control. For Robinsonville, MS, optimal Palmer amaranth control could be obtained with 370-μm (Coarse) droplets, and 90% maximum control could be sustained with 680 μm (Ultra Coarse) droplets. Differences in optimal droplet size across location could be a result of convoluted interactions between droplet size, weather conditions, population density, plant morphology, and soil fertility levels. Future research should adopt a holistic approach to identify and investigate the influence of environmental and application parameters to optimize droplet size recommendations.

How do we acquire moral obligations to others? The most straightforward cases are those where we acquire obligations as the result of particular actions which we voluntarily perform. If I promise you that I will trim your hedge, I face a moral Obligation to uphold my promise, and in the absence of some morally significant countervailing reason, I should indeed cut your hedge. Moral obligations which arise as a result of wrongdoing, as a function of corrective justice, are typically thought to be of a similar nature.

We report a significant advance in thermally insulating transparent materials: silica-based monoliths with controlled porosity which exhibit the transparency of windows in combination with a thermal conductivity comparable to aerogels.

The lack of transparent, thermally insulating windows leads to substantial heat loss in commercial and residential buildings, which accounts for ~4.2% of primary US energy consumption annually. The present study provides a potential solution to this problem by demonstrating that ambiently dried silica aerogel monoliths, i.e., ambigels, can simultaneously achieve high optical transparency and low thermal conductivity without supercritical drying. A combination of tetraethoxysilane, methyltriethoxysilane, and post-gelation surface modification precursors were used to synthesize ambiently dried materials with varying pore fractions and pore sizes. By controlling the synthesis and processing conditions, 0.5–3 mm thick mesoporous monoliths with transmittance >95% and a thermal conductivity of 0.04 W/(m K) were produced. A narrow pore size distribution, <15 nm, led to the excellent transparency and low haze, while porosity in excess of 80% resulted in low thermal conductivity. A thermal transport model considering fractal dimension and phonon-boundary scattering is proposed to explain the low effective thermal conductivity measured. This work offers new insights into the design of transparent, energy saving windows.

Herbicide applications performed with pulse width modulation (PWM) sprayers to deliver specific spray droplet sizes could maintain product efficacy, minimize potential off-target movement, and increase flexibility in field operations. Given the continuous expansion of herbicide-resistant Palmer amaranth populations across the southern and midwestern United States, efficacious and cost-effective means of application are needed to maximize Palmer amaranth control. Experiments were conducted in two locations in Mississippi (2016, 2017, and 2018) and one location in Nebraska (2016 and 2017) for a total of 7 site-years. The objective of this study was to evaluate the influence of a range of spray droplet sizes [150 (Fine) to 900 μm (Ultra Coarse)] on lactofen and acifluorfen efficacy for Palmer amaranth control. The results of this research indicated that spray droplet size did not influence lactofen efficacy on Palmer amaranth. Palmer amaranth control and percent dry-biomass reduction remained consistent with lactofen applied within the aforementioned droplet size range. Therefore, larger spray droplets should be used as part of a drift mitigation approach. In contrast, acifluorfen application with 300-μm (Medium) spray droplets provided the greatest Palmer amaranth control. Although percent biomass reduction was numerically greater with 300-μm (Medium) droplets, results did not differ with respect to spray droplet size, possibly as a result of initial plant injury, causing weight loss, followed by regrowth. Overall, 900-μm (Ultra Coarse) droplets could be used effectively without compromising lactofen efficacy on Palmer amaranth, and 300-μm (Medium) droplets should be used to achieve maximum Palmer amaranth control with acifluorfen.

Chemical weed control remains a widely used component of integrated weed management strategies because of its cost-effectiveness and rapid removal of crop pests. Additionally, dicamba-plus-glyphosate mixtures are a commonly recommended herbicide combination to combat herbicide resistance, specifically in recently commercially released dicamba-tolerant soybean and cotton. However, increased spray drift concerns and antagonistic interactions require that the application process be optimized to maximize biological efficacy while minimizing environmental contamination potential. Field research was conducted in 2016, 2017, and 2018 across three locations (Mississippi, Nebraska, and North Dakota) for a total of six site-years. The objectives were to characterize the efficacy of a range of droplet sizes [150 µm (Fine) to 900 µm (Ultra Coarse)] using a dicamba-plus-glyphosate mixture and to create novel weed management recommendations utilizing pulse-width modulation (PWM) sprayer technology. Results across pooled site-years indicated that a droplet size of 395 µm (Coarse) maximized weed mortality from a dicamba-plus-glyphosate mixture at 94 L ha–1. However, droplet size could be increased to 620 µm (Extremely Coarse) to maintain 90% of the maximum weed mortality while further mitigating particle drift potential. Although generalized droplet size recommendations could be created across site-years, optimum droplet sizes within each site-year varied considerably and may be dependent on weed species, geographic location, weather conditions, and herbicide resistance(s) present in the field. The precise, site-specific application of a dicamba-plus-glyphosate mixture using the results of this research will allow applicators to more effectively utilize PWM sprayers, reduce particle drift potential, maintain biological efficacy, and reduce the selection pressure for the evolution of herbicide-resistant weeds.

A series of (HfN)1−x(TaN)x, ceramics with x representing the starting powder blend compositions of 0.0, 18.8, 28.1, and 46.7 at.%, have been fabricated by vacuum plasma spraying. During the plasma spraying, the mixture lost approximately 25 at.% nitrogen facilitating the precipitation of metallic and metal-rich nitride phases. These specimens underwent static air oxidation exposure up to 1700 °C. In general, it was found that the addition of tantalum nitrides to the hafnium nitrides resulted in poorer oxidation behavior. However, the 18.8 at.% specimen deviated from this trend and had the lowest observed mass change. This specimen formed a dark-colored oxide scale, indexed as Hf6Ta2O17, which acted as a passivation layer. Within the scale, hafnium oxynitride phases were observed. A transformation pathway in forming these rhombohedral oxynitride phases is proposed by the filling in of oxygen in the light element interstitial locations of the rhombohedral ε-Hf3N2 and ζ-Hf4N3 structures.