The Japanese second deep ice coring project was carried out at Dome Fuji, Antarctica. Following the drilling of the pilot hole in 2001, deep ice core drilling led by the Japanese Antarctic Research Expedition (JARE) was conducted over four austral summer seasons, beginning with the 2003/04 season and reached a depth of 3035.22 m near the bedrock in January 2007. The new drill was designed and developed with the goals of (1) solving the problems encountered during the first JARE deep coring drill and (2) achieving more efficient drilling. In particular, the maximum core length that can be drilled at one time was increased from 2.30 m to 3.84 m and the chip storage efficiency was enhanced by a special pipe with many small holes. This paper gives an outline of the improved drilling system, the progress of drilling and various drilling data.

We investigated the effects of microparticles and grain size on the microstructural evolutions and mechanical properties of polycrystalline ice. Uniaxial compression tests were conducted using fine-grained pure ice and silica-dispersed ice under various conditions. Deformation behavior of fine-grained ice was found to be characterized by stress exponent n ≈ 2 and activation energy Q ≈ 60 kJ mol−1. The derived strain rates of fine-grained ice were ≈ 1 order of magnitude larger than those of coarse-grained ice obtained in previous studies, and they were found to be independent of particle dispersion and dependent on the mean grain size of ice, with grain size exponent p ≈ 1.4. Work hardening was observed in dislocation creep, while the strain rate continued to decrease. These results indicate that the deformation mechanism of fine-grained ice is different from typical dislocation creep, often associated with n = 3. Although microparticles restricted grain growth, there was little direct effect on the deformation of fine-grained ice. Microstructural observations of the ice samples indicated that the grain boundaries were straight and that the subgrain boundary densities increased after deformation. Our experiments suggest that grain size and boundaries play important roles in the deformation processes of polycrystalline ice.

Laboratory experiments were done to better understand the electrical conduction mechanisms of impure, polycrystalline ice as represented by the 2503 m Dome Fuji (Antarctica) ice core. Also, two electrical measurement techniques for ice cores were compared and their usefulness for determining the acidity of ice cores was studied. We measured the electrical conductivity and complex permittivity of 167 slab-ice samples at frequencies from 20 Hz to 1 MHz. Measurements were performed at –21˚C for all samples, and at –110˚ to –20˚C for several samples, to examine the effects of temperature. We found linear relations between the AC loss factor and the molarity of sulfuric acid, and between the high-frequency-limit conductivity and the AC loss factor. Thus, the acidity levels can be determined from the AC loss factor. In contrast, the electrical conductivity measurement (ECM) current correlated weakly with the other parameters; furthermore, the correlation worsens at larger signal. In several samples containing high acidity, the dielectric properties had distinct changes near –81˚C. We argue that these changes were caused by a change from a liquid-vein-mediated conduction mechanism above the eutectic point of the solute/water/ ice system to a solid-phase conduction mechanism at lower temperatures.

Air bubbles trapped near the surface of an ice sheet are transformed into air hydrates below a certain depth Their volume and number varies partly with environment and climate. Air bubbles and hydrates at 120-2200 m depth in the Dome Fuji (Dome F) ice core were examined with a microscope. This depth range covers the Holocene/Last Glacial/Last Interglacial/Previous Glacial periods. No air bubbles were seen below about 1100 m depth, and air hydrates began to appear from about 600 m. The observed number of air bubbles and hydrates was similar to that found in the Vostok ice core. For the ice covering the Last Glacial Maximum period, however the hydrate concentration in the Dome F core is about half that of the Vostok core. Reference to snow metamorphism and packing does not explain this finding.

A study of c-axis orientations in the upper 1500m of the Dome C (East Antarctica) deep ice core has been carried out using an automatic ice-fabric analyzer (AIFA). Twenty-nine vertical and a few horizontal thin sections from different depths in the core have been analyzed. Several statistical parameters describing fabric strength and fabric shapes have been calculated from the c-axis orientation data. The fabric diagrams display a near-random c-axis orientation distribution in the uppermost parts of the ice sheet. A tendency of c-axis rotation towards a broad single-maximum fabric is observed in the lowest part of the studied interval. The fabric development at Dome C thus appears typical for ice-sheet summit and dome sites. The fabric development at Dome C is compared with the fabric evolution in the Dome F and GRIP ice cores, and data on crystal size obtained with image-analysis techniques are presented. Studies of misorientation angles between the c axes of neighbouring crystals reveal little evidence for polygonization, but microscopic observations show that sub-grain boundaries are present in half of the grains at any depth.

The 320 kyr climatic record from the 2503 m Dome Fuji (Antarctica) ice core was analyzed using two electrical methods: AC-ECM and ECM (electrical conductivity measurements). AC-ECM is a method to detect the complex admittance between electrodes dragged on the ice surface with mm-scale resolution and uses 1V and 1 MHz. the ratio of the real to imaginary part of the admittance is the AC loss factor, which responds linearly to the amount of sulfuric acid and hydrogen ions. Both the AC loss factor and the ECM current respond to acid, but the ECM signal tends to saturate at high acidities. Dome Fuji ice was measured to be highly acidic, with background values of 2–7 μM, and had 4500 major peaks with acidities of up to 90 μM. This ice-core evidence and earlier snow-chemistry survey around the dome region indicates that Dome F may have a better connection to the stratosphere than have sites at lower altitude, which allows more stratospheric aerosol and gases to reach the snow surface. Acidity tends to be high in interglacial periods, but correlation between acidity and δ18O is not straightforward. Electrical signals decreased and smoothed out with increasing depth; the diffusion coefficients deduced from this smoothing were 10–102 times greater than in solid ice. the ice core exhibited electromechanical effects and expelling effects from sulfate peaks.

In the mid-1990s, excellent results from the GRIP and GISP2 deep drilling projects in Greenland opened up funding for continued ice-coring efforts in Antarctica (EPICA) and Greenland (NorthGRIP). The Glaciology Group of the Niels Bohr Institute, University of Copenhagen, was assigned the task of providing drilling capability for these projects, as it had done for the GRIP project. The group decided to further simplify existing deep drill designs for better reliability and ease of handling. The drill design decided upon was successfully tested on Hans Tausen Ice Cap, Peary Land, Greenland, in 1995. The 5.0m long Hans Tausen (HT) drill was a prototype for the ~11m long EPICA and NorthGRIP versions of the drill which were mechanically identical to the HT drill except for a much longer core barrel and chips chamber. These drills could deliver up to 4m long ice cores after some design improvements had been introduced. The Berkner Island (Antarctica) drill is also an extended HT drill capable of drilling 2 m long cores. The success of the mechanical design of the HT drill is manifested by over 12 km of good-quality ice cores drilled by the HT drill and its derivatives since 1995.

In order to understand and solve the ‘warm-ice problem’ in deep ice-core drilling, we applied the metal-cutting theory to ice and estimated the heat generated during ice coring taking into account the mechanical and thermal properties of the ice and cutters. We found that (1) most of the heat in cutting is generated by shear deformation at the shear plane of ice, and the heat could increase the chip temperature by several degrees; (2) the rake angle of the cutter has more influence on the temperature increase in chips than the barrel rotation speed and penetration pitch; (3) if the cutter is made of a material with larger thermal conductivity, the temperature increase in the chips can be reduced; and (4) if the density of the liquid is less than the density of ice, the cutting chips sink to the bottom and the friction heat generated by the drill head and slush can raise the ambient temperature of the drill head by several degrees.

An automatic ice-fabric analyzer has been developed, which can determine individual ,-axis orientations by image-analysis techniques. The analyzer consists of four major components: a sample stage, a pair of crossed polaroids, a charge coupled device (CCD) camera and a light source. Both the sample stage and the crossed polaroids can be rotated independently of each other by the stepping motors controlled by a personal computer (PC). Measurements are conducted as follows. An ice thin section is set on the sample stage and then the crossed polaroids are rotated. Thin-section images are recorded by the PC at intervals of 2° of rotation. From the image-intensity (gray value) dataset of each crystal in the thin section the extinction angles of individual crystals can be determined. Similarly, eight other extinction angles of individual crystals are obtained from eight other CCD camera positions with respect to the thin section: Finally, the .-axis orientation of individual crystals is calculated by using these extinction angles. With this technique, all crystals within the view of the CCD camera can be analyzed at the same time. In addition, with image-processing techniques the individual crystals are recognized automatically and other parameters, such as grain-size and grain shape, can be measured simultaneously. Textural studies of Dome Fuji (Antarctica) ice cores have been conducted with this analyzer.

Ice in polar ice sheets undergoes deformation during its flow towards the coast. Deformation and recrystallization microstructures such as subgrain boundaries can be observed and recorded using high-resolution light microscopy of sublimation-edged sample surfaces (microstructure mapping). Subgrain boundaries observed by microstructure mapping reveal characteristic shapes and arrangements. As these arrangements are related to the basal plane orientation, full crystallographic orientation measurements are needed for further characterization and interpretation of the subgrain boundary types. X-ray Laue diffraction measurements validate the sensitivity of different boundary types with sublimation used by microstructure mapping for the classification. X-ray Laue diffraction provides misorientation values of all four crystal axes. Line scans across a subgrain boundary pre-located by microstructure mapping can determine the rotation axis and angle. Together with the orientation of the subgrain boundary this yields information on the dislocation types. Tilt and twist boundaries composed of dislocations lying in the basal plane, and tilt boundaries composed of nonbasal dislocations were found. A statistical analysis shows that nonbasal dislocations play a significant role in the formation of all subgrain boundaries.

Subgrain boundaries revealed as shallow sublimation grooves on ice sample surfaces are a direct and easily observable feature of intracrystalline deformation and recrystallization. Statistical data obtained from the EPICA Dronning Maud Land (EDML) deep ice core drilled in East Antarctica cannot detect a depth region of increased subgrain-boundary formation. Grain-boundary morphologies show a strong influence of internal strain energy on the microstructure at all depths. The data do not support the classical view of a change of dominating recrystallization regimes with depth. Three major types of subgrain boundaries, reflecting high mechanical anisotropy, are specified in combination with crystal-orientation analysis.

This work presents a method of mapping deformation-related sublimation patterns, formed on the surface of ice specimens, at microscopic resolution (3–4 μm pixel−1). The method is based on the systematic sublimation of a microtomed piece of ice, prepared either as a thick or a thin section. The mapping system consists of an optical microscope, a CCD video camera and a computer-controlled xy-stage. About 1500 images are needed to build a high-resolution mosaic map of a 4.5 × 9 cm section. Mosaics and single images are used to derive a variety of statistical data about air inclusions (air bubbles and air clathrate hydrates), texture (grain size, shape and orientation) and deformation-related features (subgrain boundaries, slip bands, subgrain islands and loops, pinned and bulged grain boundaries). The most common sublimation patterns are described, and their relevance for the deformation of polar ice is briefly discussed.

Results of laboratory uniaxial compression tests over the stress range 0.18–0.52 MPa and the strain range 0.5–8.6% at approximately –5 and –20°C are presented. Grain-size analysis and comparisons with annealing tests confirm that grain-growth reducing processes are active during deformation. Microstructural observations reveal that subgrain-rotation recrystallization and grain-shape changes due to strain-induced grain-boundary migration are the causes of the grain-growth deceleration. Further results from microstructural observations show that obstacle formation by dislocation walls and subgrain boundaries is the reason for isotropic hardening during creep. Subgrainboundary types that are likely to be relevant for studies on the activity of different dislocation types are described.

Chemical stratigraphy in association with the texture of snow cover was studied during the period from the severe winter to the early snowmelt season. The vertical concentration profiles of N03−, SO42−, Cl− and Na+ were generally preserved until the initial stage of the snowmelt season, while there were appreciable variations in ionic concentrations. At the initial stage of the snowmelt season, redistribution of chemical constituents in the snow cover occurred in a complicated way, dependent on both the structure of internal layers and the chemical species. Major peaks, however, still remained in the profiles.

A new flow law for anisotropic polycrystalline ice is presented. The strain-rate tensor is related by a geometrical factor tensor (G) to the stress tensor. The G factor tensor can be obtained front the c-axis fabric data and stress condition. This new flow law describes well the direction-dependent mechanical properties of anisotropic ice which cannot be demonstrated by Glen’s flow law. For example, the new flow law can explain the fact that a strong single-maximum fabric ice, such as Dye 3 Wisconsin ice, can deform several times faster than isotropic ice under horizontal shear but can hardly deform under vertical or horizontal normal stress. We also show that at a deeper part of an ice sheet, where a single-maximum fabric develops, a positive vertical strain rate can be produced with only a horizontal shear stress.

Uniaxial compression tests were carried out with specimens cut from several deep ice cores obtained at Dye 3, Greenland, in 1980 and 1981. The power law relationship of = Αση was obtained between the uniaxial strain-rate and the uniaxial stress σ. In a range of strain-rates between 10−8 and 10−7 s−1, the value of the power n for samples with strong single maximum fabric was approximately 4, significantly larger than the value of 3 which has been generally accepted from experiments using artificial polycrystalline ice. A work-hardening effect was found in the ice-core samples taken from a depth of 1900 m, which had a smaller grain size than the others. Recrystallization occurred when the temperature of the specimen was raised during the test and this ultimately caused the formation of the so-called diamond pattern ice fabric.

Structural laboratory studies were made of ice collected at the surface and from a shallow bore hole in the bare ice near the Allan Hills, Victoria Land, Antarctica. The results obtained were combined with glaciological survey data to describe the mechanism of accumulation of meteorites by ice flow in a marginal area of the East Antarctic ice sheet. The age of the bare ice, approximately 20 ka, was estimated by fabric characteristics and grain size of the ice. This conforms to the minimum value of the terrestrial age of the meteorites found in the same area. The several hundred meteorite finds concentrated in the bare-ice area can be explained by an expanded catchment area during a previous ice age, or by a correction factor for the estimate of the influx rate of meteorite fall, or more probably by a combination of both.