This study is dedicated to achieving efficient active noise control in a supersonic underexpanded planar jet, utilizing control parameters informed by resolvent analysis. The baseline supersonic underexpanded jet exhibits complex wave structures and substantial high-amplitude noise radiations. To perform the active control, unsteady blowing and suction are applied along the nozzle inner wall close to the exit. Employing both standard and acoustic resolvent analyses, a suitable frequency and spanwise wavenumber range for the blowing and suction is identified. Within this range, the control forcing can be significantly amplified in the near field, effectively altering the original sound-producing energetic structure while minimizing far-field amplification to prevent excessive noise. A series of large-eddy simulations are further conducted to validate the control efficiency, demonstrating an over 10 dB reduction in upstream-propagated screech noise. It is identified that the present unsteady control proves more effective than steady control at the same momentum coefficient. The controlled jet flow indicates that the shock structures become more stable, and the stronger the streamwise amplification of the forcing, the more likely it is to modify the mean flow characteristics, which is beneficial for reducing far-field noise radiation. Spectral proper orthogonal decomposition analysis of the controlled flow confirms that the control redistributes energy to higher forcing frequencies and suppresses large-scale antisymmetric and symmetric modes related to screech and its harmonics. The findings of this study highlight the potential of resolvent-guided control techniques in reducing noise in supersonic underexpanded jets and provide a detailed understanding of the inherent mechanisms for effective noise reduction through active control strategies.

This paper presents systematic molecular dynamics modelling of Na-montmorillonite subjected to uniaxial compression and unidirectional shearing. An initial 3D model of a single-cell Na-montmorillonite structure is established using the Build Crystal module. The space group is C2/m, and COMPASS force fields are applied. Hydration analysis of Na-montmorillonite has been performed to validate the simulation procedures, where the number of absorbed water molecules varied with respect to the various lattice parameters. A series of uniaxial compression stress σzz and unidirectional shear stress τxy values are applied to the Na-montmorillonite structure. It is shown that the lattice parameter and hydration degree exhibit significant influence on the stress–strain relationship of Na-montmorillonite. The ultimate strain increases with increases in the lattice parameter but decreases in the number of water molecules. For saturated Na-montmorillonite, more water molecules result in a stiffer clay mineral under uniaxial compression and unidirectional shearing.

This study is performed to figure out how the presence of diabetes affects the infection, progression and prognosis of 2019 novel coronavirus disease (COVID-19), and the effective therapy that can treat the diabetes-complicated patients with COVID-19. A multicentre study was performed in four hospitals. COVID-19 patients with diabetes mellitus (DM) or hyperglycaemia were compared with those without these conditions and matched by propensity score matching for their clinical progress and outcome. Totally, 2444 confirmed COVID-19 patients were recruited, from whom 336 had DM. Compared to 1344 non-DM patients with age and sex matched, DM-COVID-19 patients had significantly higher rates of intensive care unit entrance (12.43% vs. 6.58%, P = 0.014), kidney failure (9.20% vs. 4.05%, P = 0.027) and mortality (25.00% vs. 18.15%, P < 0.001). Age and sex-stratified comparison revealed increased susceptibility to COVID-19 only from females with DM. For either non-DM or DM group, hyperglycaemia was associated with adverse outcomes, featured by higher rates of severe pneumonia and mortality, in comparison with non-hyperglycaemia. This was accompanied by significantly altered laboratory indicators including lymphocyte and neutrophil percentage, C-reactive protein and urea nitrogen level, all with correlation coefficients >0.35. Both diabetes and hyperglycaemia were independently associated with adverse prognosis of COVID-19, with hazard ratios of 10.41 and 3.58, respectively.

The subgrid effects on the dynamics of the filtered velocity gradient tensor (VGT) in compressible turbulence are studied by means of statistical analysis of the invariants of the filtered VGT in compressible mixing layers. The evolution of the filtered VGT is determined by the interaction among the invariants, the pressure effects, the viscous effects and the subgrid effects. Based on the probability fluxes in the plane of the second ($Q$) and the third ($R$) invariants of the filtered VGT, it is found that the flux for the subgrid effect term changes most with the dilatation compared to the other terms. Further, a Schur decomposition of the filtered VGT into its normal part and non-normal part, which represent the local effect and the non-local effect of the flow dynamics, respectively, is used to deal with their effects of the velocity gradient. It is revealed that the compressibility is mainly related to the normal effect while the behaviour of the subgrid-scale (SGS) energy dissipation is mainly associated with the non-normal effect. A backscattering region of the SGS energy dissipation in the $Q$–$R$ plane is identified in the locally expanded regions, which is determined by the non-normal effect. Further, an SGS model with the non-local effect is proposed to give a better prediction of the SGS energy dissipation.

A new band-reject frequency-selective surface (FSS) based on dual-band near-zero refractive index metamaterial (ZIM) design is presented in this paper. Consisting of a planar array of complementary dual-layer symmetry resonant ring, the proposed FSS exhibits a high-selective band-reject filtering response. From the viewpoint of effective medium, the subwavelength FSS is characterized by near-zero effective magnetic permeability and near-zero effective electric permittivity in two different operational bands, respectively. The corresponding resonant behavior and E-field distributions are analyzed in detail. A prototype of the proposed FSS working in X-band is fabricated and measured. The simulation and experiment results verify the effectiveness and correctness of the ZIM-based design method.

We examined the in vitro developmental competence of parthenogenetic activation (PA) oocytes activated by an electric pulse (EP) and treated with various concentrations of AZD5438 for 4 h. Treatment with 10 µM AZD5438 for 4 h significantly improved the blastocyst formation rate of PA oocytes in comparison with 0, 20, or 50 µM AZD5438 treatment (46.4% vs. 34.5%, 32.3%, and 24.0%, respectively; P < 0.05). The blastocyst formation rate was higher in the group treated with AZD5438 for 4 h than in the groups treated with AZD5438 for 2 or 6 h (42.8% vs. 38.6% and 37.2%, respectively; P > 0.05). Furthermore, 66.67% of blastocysts derived from these AZD5438-treated PA oocytes had a diploid karyotype. The blastocyst formation rate of PA and somatic cell nuclear transfer (SCNT) embryos was similar between oocytes activated by an EP and treated with 2 mM 6-dimethylaminopurine for 4 h and those activated by an EP and treated with 10 µM AZD5438 for 4 h (11.11% vs. 13.40%, P > 0.05). In addition, the level of maturation-promoting factor (MPF) was significantly decreased in oocytes activated by an EP and treated with 10 µM AZD5438 for 4 h. Finally, the mRNA expression levels of apoptosis-related genes (Bax and Bcl-2) and pluripotency-related genes (Oct4, Nanog, and Sox2) were checked by RT-PCR; however, there were no differences between the AZD5438-treated and non-treated control groups. Our results demonstrate that porcine oocyte activation via an EP in combination with AZD5438 treatment can lead to a high blastocyst formation rate in PA and SCNT experiments.

A compact three-dimensional (3D) circularly polarized (CP) microstrip antenna is presented in this paper. The antenna adopts three low-cost printed circuit boards to form an integrated and closed 3D structure, and the radiation patch and the feed patches are etched on the surface of that. A crossed slot is cut on the radiation patch to miniaturize the antenna, and triangular feed patches are introduced to increase the bandwidths. In addition, because of the utilization of a low-loss series feed line, the antenna has a high efficiency of more than 95%. A prototype of the antenna is measured to validate the method. The dimensions of the antenna is 0.064λ × 0.36λ (λ is the wavelength in free space at 1.2 GHz). The results indicate that the impedance bandwidth for voltage standing wave ratio ≤ 2 reaches 23%, and the bandwidth for axial ratio (AR) ≤ 3 dB reaches 10.1%. In the overlap band, the gains are > 4.5dBic. Additionally, the 3 dB beamwidth is more than 114°, and the beamwidth for AR ≤ 3 dB is more than 131° at 1.2 GHz.

The pure and Er3+-modified binary Pb(Zn1/3Nb2/3)O3–9PbTiO3 (PZN–9PT) single crystals were grown by using the flux method. The phase structure of the as-grown single crystals at room temperature was confirmed by the x-ray diffraction analysis. The effect of Er3+ addition on the electrical properties and upconversion luminescence of PZN–9PT was investigated. The rhombohedral to tetragonal phase transition temperature and the Curie temperature of the Er3+-modified PZN–9PT single crystals were 370 and 451 K, respectively. The coercive field E C at room temperature was evidently higher by 11.6 kV/cm than that of the PZN–9PT single crystals (E C, ∼3.5 kV/cm). Furthermore, the green and red upconversion emission bands were obtained under the 980 nm excitation, which are related to (2H11/2, 4S3/2) → 4I15/2 and 4F9/2 → 4I15/2 transitions.

We investigated the effect of human induced pluripotent stem cell (hiPS) medium on porcine somatic cell nuclear transfer and bovine in vitro fertilized early blastocysts, in comparison with North Carolina State University (NCSU)-37 medium and in vitro culture (IVC)-II medium. After 2 days of culture, the diameter of the portion of the blastocyst that was extruded from the zona pellucid dramatically differed between porcine blastocysts cultured in hiPS medium and those cultured in NCSU-37 medium (221.47 ± 38.94 μm versus 481.87 ± 40.61 μm, P < 0.01). Moreover, the diameter of the portion of the blastocyst significantly differed between bovine blastocysts cultured in hiPS medium and those cultured in IVC-II medium (150.30 ± 29.49 μm versus 195.58 ± 41.59 μm, P < 0.01). Furthermore, the total number of cells per porcine and bovine blastocyst was more than two-fold higher in blastocysts cultured in hiPS medium than in those cultured in NCSU-37 medium (44.33 ± 5.28 and 143.33 ± 16.05, P < 0.01) or IVC-II medium (172.12 ± 45.08 and 604.83 ± 242.64, P < 0.01), respectively. These results indicate that hiPS medium markedly improves the quality of porcine and bovine blastocysts.

In this paper, a compact multiple-input multiple-output (MIMO) antenna system with high isolation is proposed for 2.4 GHz wireless local area network (WLAN) application. The system is composed of two aperture-coupled shorted patch antennas with a spacing of 4 mm (only 0.032λ). The antenna is fed with an H-shaped coupling slot, and the defected shorting wall is used for high isolation. The proposed MIMO system exhibits an isolation of better than −20 dB and a maximum isolation of −43 dB at the central frequency. The envelope correlation coefficient is less than 0.01. The simulated and measured results show that the proposed antenna is a good candidate for MIMO system with higher isolation and better diversity.

A method to design the composite insulation structures in pulsed power systems is proposed in this paper. The theoretical bases for this method include the Weibull statistical distribution and the empirical insulation formula. A uniform formula to describe the reliability (R) for different insulation media such as solid, liquid, gas, vacuum, and vacuum surface is derived. The dependence curves of the normalized applied field on R are also obtained. These curves show that the normalized applied field decreases rapidly as R increases but the declining rates corresponding to different insulation media are different. In addition, if R is required to be higher than a given level, the normalized applied field should be smaller than a certain value. In practical design, the common range of the applied fields for different insulation media should be chosen to meet a global reliability requirement. In the end, the proposed method is demonstrated with a specific coaxial high-voltage vacuum insulator.

The studies of differences in life history and suitability of both water temperatures and trophic levels among rotifer sibling species improve our understanding of speciation, sibling species coexistence and possible niche differentiation over space and time, and consequences for the functioning of ecosystems induced by climate change and eutrophication. We collected Brachionus calyciflorus from Lake Baixiang and Lake Kongque, two tropical shallow lakes, in Xishuangbanna city, Yunnan, China, clonally cultured them in laboratory, and found that the B. calyciflorus complex contains two sibling species named sibling species BNA13 and BNB3 by phylogenetic analysis, and investigated the life-table parameters of the two sibling species BNA13 and BNB3 at four temperatures (16, 20, 24 and 28°C) and four algal densities (0.5, 1.0, 2.0 and 4.0×106 cells.mL−1). The results showed that the responses to increasing temperature and algal density for each of the life-table parameters differed with rotifer sibling species. Sibling species, temperature, algal density and their interactions almost all significantly affected the durations of juvenile period, embryonic development, reproductive period, post-reproductive period, mean lifespan, net reproductive rate, generation time and intrinsic rate of population growth. Sibling species significantly affected the age-specific survivorship. Temperature, algal density and their interaction and the interaction of sibling species and temperature significantly affected the age-specific fecundity. Regardless of the effects of temperature and algal density, the durations of juvenile period, embryonic development, reproductive period, post-reproductive period and mean lifespan, age-specific survivorship, net reproductive rate and generation time of the B. calyciflorus sibling species BNA13 were greater than those of BNB3, but the intrinsic rate of population growth of BNA13 was lower than those of BNB3. This suggests that the two B. calyciflorus sibling species adopted variable life history strategies, low population growth and high survivorship for sibling species BNA13, and high population growth and low survivorship for sibling species BNB3. Both the intrinsic rates of population growth of BNA13 and BNB3 were the highest at 28°C and 4.0×106 cells.mL−1 algal density, indicating that some adaptations of the B. calyciflorus sibling species BNA13 and BNB3 in tropical shallow lakes to water temperatures and trophic levels were similar, and they have the potential for coexistence in single waterbody of higher temperature and higher trophic level.

Predator–prey interactions play major and direct roles in the structuring of zooplankton communities. Asplanchna usually predates ciliates, rotifers, cladocerans and sometimes even copepods, its predation may drive not only the ecological, but also the evolutionary dynamics of prey populations. In the present study, the life-table demography and the population growth of Asplanchna brightwelli were investigated at four temperatures (16, 20, 24 and 28°C) using Brachionus angularis as prey at four densities (10, 20, 30 and 40 ind.mL−1). The results showed that temperature affected significantly all the life-table demographic parameters (age-specific survivorship and fecundity, average lifespan, life expectancy at hatching, generation time, net reproductive rate and intrinsic rate of population increase) and the population growth rate obtained from the population growth studies, prey density affected the generation time, the net reproductive rate, the intrinsic rate of population increase and the population growth rate, and the interaction between temperature and prey density affected the generation time and the population growth rate. Both the average lifespan and the life expectancy at hatching were the longest at 16°C, the generation times were longer at lower temperatures (16 and 20°C) and higher prey densities (30 and 40 ind.mL−1), the net reproductive rates were higher at lower temperatures (16 and 20°C) and 20–40 ind.mL−1 of B. angularis, and the population growth rates were higher at 20°C under 20–40 ind.mL−1 of B. angularis.