This study presents a novel investigation into the vortex dynamics of flow around a near-wall rectangular cylinder based on direct numerical simulation at $Re=1000$, marking the first in-depth exploration of these phenomena. By varying aspect ratios ($L/D = 5$, $10$, $15$) and gap ratios ($G/D = 0.1$, $0.3$, $0.9$), the study reveals the vortex dynamics influenced by the near-wall effect, considering the incoming laminar boundary layer flow. Both $L/D$ and $G/D$ significantly influence vortex dynamics, leading to behaviours not observed in previous bluff body flows. As $G/D$ increases, the streamwise scale of the upper leading edge (ULE) recirculation grows, delaying flow reattachment. At smaller $G/D$, lower leading edge (LLE) recirculation is suppressed, with upper Kelvin–Helmholtz vortices merging to form the ULE vortex, followed by instability, differing from conventional flow dynamics. Larger $G/D$ promotes the formation of an LLE shear layer. An intriguing finding at $L/D = 5$ and $G/D = 0.1$ is the backward flow of fluid from the downstream region to the upper side of the cylinder. At $G/D = 0.3$, double-trailing-edge vortices emerge for larger $L/D$, with two distinct flow behaviours associated with two interactions between gap flow and wall recirculation. These interactions lead to different multiple flow separations. For $G/D = 0.9$, the secondary vortex (SV) from the plate wall induces the formation of a tertiary vortex from the lower side of the cylinder. Double-SVs are observed at $L/D = 5$. Frequency locking is observed in most cases, but is suppressed at $L/D = 10$ and $G/D = 0.9$, where competing shedding modes lead to two distinct evolutions of the SV.

A high-energy pulsed vacuum ultraviolet (VUV) solid-state laser at 177 nm with high peak power by the sixth harmonic of a neodymium-doped yttrium aluminum garnet (Nd:YAG) amplifier in a KBe2BO3F2 prism-coupled device was demonstrated. The ultraviolet (UV) pump laser is a 352 ps pulsed, spatial top-hat super-Gaussian beam at 355 nm. A high energy of a 7.12 mJ VUV laser at 177 nm is obtained with a pulse width of 255 ps, indicating a peak power of 28 MW, and the conversion efficiency is 9.42% from 355 to 177 nm. The measured results fitted well with the theoretical prediction. It is the highest pulse energy and highest peak power ever reported in the VUV range for any solid-state lasers. The high-energy, high-peak-power, and high-spatial-uniformity VUV laser is of great interest for ultra-fine machining and particle-size measurements using UV in-line Fraunhofer holography diagnostics.

The large number of patients with ankle injuries and the high incidence make ankle rehabilitation an urgent health problem. However, there is a certain degree of difference between the motion of most ankle rehabilitation robots and the actual axis of the human ankle. To achieve more precise ankle joint rehabilitation training, this paper proposes a novel 3-PUU/R parallel ankle rehabilitation mechanism that integrates with the human ankle joint axis. Moreover, it provides comprehensive ankle joint motion necessary for effective rehabilitation. The mechanism has four degrees of freedom (DOFs), enabling plantarflexion/dorsiflexion, eversion/inversion, internal rotation/external rotation, and dorsal extension of the ankle joint. First, based on the DOFs of the human ankle joint and the variation pattern of the joint axes, a 3-PUU/R parallel ankle joint rehabilitation mechanism is designed. Based on the screw theory, the inverse kinematics inverse, complete Jacobian matrix, singular characteristics, and workspace analysis of the mechanism are conducted. Subsequently, the motion performance of the mechanism is analyzed based on the motion/force transmission indices and the constraint indices. Then, the performance of the mechanism is optimized according to human physiological characteristics, with the motion/force transmission ratio and workspace range as optimization objectives. Finally, a physical prototype of the proposed robot was developed, and experimental tests were performed to evaluate the above performance of the proposed robot. This study provides a good prospect for improving the comfort and safety of ankle joint rehabilitation from the perspective of human-machine axis matching.

The numerical investigation focuses on the flow patterns around a rectangular cylinder with three aspect ratios ($L/D=5$, $10$, $15$) at a Reynolds number of $1000$. The study delves into the dynamics of vortices, their associated frequencies, the evolution of the boundary layer and the decay of the wake. Kelvin–Helmholtz (KH) vortices originate from the leading edge (LE) shear layer and transform into hairpin vortices. Specifically, at $L/D=5$, three KH vortices merge into a single LE vortex. However, at $L/D=10$ and $15$, two KH vortices combine to form a LE vortex, with the rapid formation of hairpin vortex packets. A fractional harmonic arises due to feedback from the split LE shear layer moving upstream, triggering interaction with the reverse flow. Trailing edge (TE) vortices shed, creating a Kármán-like street in the wake. The intensity of wake oscillation at $L/D=5$ surpasses that in the other two cases. Boundary layer transition occurs after the saturation of disturbance energy for $L/D=10$ and $15$, but not for $L/D=5$. The low-frequency disturbances are selected to generate streaks inside the boundary layer. The TE vortex shedding induces the formation of a favourable pressure gradient, accelerating the flow and fostering boundary layer relaminarization. The self-similarity of the velocity defect is observed in all three wakes, accompanied by the decay of disturbance energy. Importantly, the decrease in the shedding frequency of LE (TE) vortices significantly contributes to the overall decay of disturbance energy. This comprehensive exploration provides insights into complex flow phenomena and their underlying dynamics.

Straightplasma channels are widely used to guide relativistic intense laser pulses over several Rayleigh lengths for laser wakefield acceleration. Recently, a curved plasma channel with gradually varied curvature was suggested to guide a fresh intense laser pulse and merge it into a straight channel for staged wakefield acceleration [Phys. Rev. Lett. 120, 154801 (2018)]. In this work, we report the generation of such a curved plasma channel from a discharged capillary. Both longitudinal and transverse density distributions of the plasma inside the channel were diagnosed by analyzing the discharging spectroscopy. Effects of the gas-filling mode, back pressure and discharging voltage on the plasma density distribution inside the specially designed capillary are studied. Experiments show that a longitudinally uniform and transversely parabolic plasma channel with a maximum channel depth of 47.5 μm and length of 3 cm can be produced, which is temporally stable enough for laser guiding. Using such a plasma channel, a laser pulse with duration of 30 fs has been successfully guided along the channel with the propagation direction bent by 10.4°.

This study is designed to explore the association between dietary betaine intake and risk of all-cause and cardiovascular death in patients with coronary artery diseases (CAD). In this cohort study, 1292 patients with CAD were followed up for a median of 9·2 years. Baseline dietary betaine intake was collected using a paper-based semi-quantitative FFQ and assessed according to the US Department of Agriculture (USDA) database and the data of betaine in common foods. Cox proportional hazards regression models were used to analyse the association between dietary betaine intake and risks of all-cause and cardiovascular mortality. During the follow-up periods, 259 deaths recorded in 1292 participants, of which 167 died of CVD. Patients in the highest tertile of dietary betaine intake had a lower risk of all-cause (P = 0·007) and cardiovascular death (P < 0·001) than those in the lowest tertile after adjusting for age and sex, traditional cardiovascular risk factors and other potential confounders. After further adjusting for plasma methionine metabolites and vitamins, hazard ratio across tertiles of dietary betaine intake were 1·00, 0·84 and 0·72 for all-cause mortality (P for trend = 0·124), and 1·00, 0·77 and 0·55 for cardiovascular mortality (P for trend = 0·021). Higher dietary betaine intake was associated with a decreased risk of cardiovascular death after fully adjustment for cardiovascular risk factors, other potential confounders and plasma methionine metabolites and vitamins. However, the association between dietary betaine intake and risk of all-cause mortality was not statistically significant after further adjusting for plasma methionine metabolites and vitamins.

Eating architecture is a term that describes meal frequency, meal timing and meal size and the daily variation in each of these. The aim of this study was to determine the relationship between components of eating architecture on body fat and markers of glycaemic control in healthy adults at increased risk of type 2 diabetes (T2DM). Participants (n 73, 39 males, age 58·8 (8·1) years, BMI 33·4 (4·4) kg/m2) recorded food intake and wore accelerometers and continuous glucose monitors (CGM) for 7–14 d under free-living conditions. Body fat and glycated Hb (HbA1c) were also measured. The mean and day-to-day variation (calculated as the standard deviation during the monitoring period) of each component of eating architecture were calculated. Multivariable linear regression models were constructed for three separate outcome variables (body fat mass, mean CGM glucose and HbA1c) for each component of eating architecture before and after adjustment for confounders. Higher variability in the time of first meal consumption was associated with increased body fat mass after adjusting for confounders (β = 0·227, 95 % CI: 0·019, 0·434, P = 0·033). Increased variability in the time lag from waking to first meal consumption was also positively associated with increased HbA1c after adjustment (β = 0·285, 95 % CI: 0·040, 0·530, P = 0·023). Low day-to-day variability in first meal consumption was associated with lower body fat and improved glucose control in adults at increased risk of T2DM. Routine consumption of meals may optimise temporal regulation to anticipate and respond appropriately to a glucose challenge.

This study examined the effect of a cryoprotectant with and without pentoxifylline supplementation on the motility and viability of human testicular sperm, both before and after freezing. Testicular samples were obtained from 68 patients with azoospermia who came to the Andrology Service of West China Second University Hospital, Sichuan University, for testicular biopsies from December 2019 to April 2020. All patients were assigned randomly to two groups: experimental, whose testicular sperm were added to the cryoprotectant with pentoxifylline, and the control, whose testicular sperm were added to the cryoprotectant without pentoxifylline. Both groups used the same freezing and thawing methods. Testicular sperm motility in the experimental group was significantly higher than that of the control group, both before and after cryopreservation. The recovery rate of sperm motility in the experimental group was significantly higher than that of the control group. The percentage of samples with motile testicular sperm in the experimental group was significantly higher than that of the control group after thawing. Sperm viability was unchanged between the experimental and control groups, both before and after freezing. Overall, a pentoxifylline-supplemented cryoprotectant can significantly improve the motility of testicular sperm before and after cryopreservation.

A highly active catalyst of cerium–tungsten–titanium mixed oxide was synthesized by introducing Ce4+ and H2O2 in the base sample of Ce20W10Ti100Oz–Ce3+. As a consequence, the NH3-SCR activity of Ce20W10Ti100Oz–Ce3+ is significantly improved as the additives of Ce4+ and H2O2 enlarge the Brunauer–Emmett–Teller (BET) surface area by refining its pore size. Meanwhile, the introduction of Ce4+ increases the Lewis acid sites of Ce20W10Ti100Oz–Ce3+ and decreases its low-temperature Brønsted acid sites. The further addition of H2O2 improves the Brønsted acid sites and dispersion of cerium/tungsten species, and thereby enhances the concentrations of the adsorbed oxygen (Oα) and the adsorbed oxygen $\lpar {\rm {O}^{\prime}}_{\rm \alpha} \rpar$ due to the activation of chemisorbed water on the surface of the catalyst. The addition of Ce4+ and H2O2 shows a synergistic promotional effect, which is due to the largest BET surface area and the highest concentrations of Oα or/and ${\rm {O}^{\prime}}_{\rm \alpha}$. Ce20W10Ti100Oz–Ce3+:Ce4+ = 17.5:2.5 + H2O2 exhibits the highest catalytic activity compared with the conventional ones (Fig. 5).

The extent of intertidal flats in the Yellow Sea region has declined significantly in the past few decades, resulting in severe population declines in several waterbird species. The Yellow Sea region holds the primary stopover sites for many shorebirds during their migration to and from northern breeding grounds. However, the functional roles of these sites in shorebirds’ stopover ecology remain poorly understood. Through field surveys between July and November 2015, we investigated the stopover and moult schedules of migratory shorebirds along the southern Jiangsu coast, eastern China during their southbound migration, with a focus on the ‘Critically Endangered’ Spoon-billed Sandpiper Calidris pygmaea and ‘Endangered’ Nordmann’s Greenshank Tringa guttifer. Long-term count data indicate that both species regularly occur in globally important number in southern Jiangsu coast, constituting 16.67–49.34% and 64.0–80.67% of their global population estimates respectively, and it is highly likely that most adults undergo their primary moult during this southbound migration stopover. Our results show that Spoon-billed Sandpiper and Nordmann’s Greenshank staged for an extended period of time (66 and 84 days, respectively) to complete their primary moult. On average, Spoon-billed Sandpipers and Nordmann’s Greenshanks started moulting primary feathers on 8 August ± 4.52 and 27 July ± 1.56 days respectively, and their moult durations were 72.58 ± 9.08 and 65.09 ± 2.40 days. In addition, some individuals of several other shorebird species including the ‘Endangered’ Great Knot Calidris tenuirostris, ‘Near Threatened’ Bar-tailed Godwit Limosa lapponica, ‘Near Threatened’ Eurasian Curlew Numenius arquata and Greater Sand Plover Charadrius leschenaultii also underwent primary moult. Our work highlights the importance of the southern Jiangsu region as the primary moulting ground for these species, reinforcing that conservation of shorebird habitat including both intertidal flats and supratidal roosting sites in this region is critical to safeguard the future of some highly threatened shorebird species.

To evaluate the effects of different anthropogenic activities on zooplankton and the pelagic ecosystem, we conducted seasonal cruises in 2010 to assess spatial heterogeneity among the mesozooplankton communities of Xiangshan Bay, a subtropical semi-enclosed bay in China. The evaluation included five different areas: a kelp farm, an oyster farm, a fish farm, the thermal discharge area of a power plant, and an artificial reef, and we aimed to identify whether anthropogenic activities dominated spatial variation in the mesozooplankton communities. The results demonstrated clear spatial heterogeneity among the mesozooplankton communities of the studied areas, dominantly driven by natural hydrographic properties, except in the area near the thermal discharge outlet of the power station. In the outlet area, thermal shock caused by the discharge influenced the mesozooplankton community by decreasing abundance and biomass throughout the four seasons, even causing a shift in the dominant species near the outlet during summer from Acartia pacifica to eurythermal and warm water taxa. Unique features of the mesozooplankton community in the oyster farm may be due to the combined effects of oyster culture and the natural environment in the branch harbour. However, kelp and fish culture, and the construction of an artificial reef did not exert any obvious influence on the mesozooplankton communities up to 2010, probably because of the small scale of the aquaculture and a time lag in the rehabilitation effects of the artificial reef. Thus, our results suggested that the dominant factors influencing spatial variations of mesozooplankton communities in Xiangshan Bay were still the natural hydrographic properties, but the thermal discharge was an anthropogenic activity that changed the pelagic ecosystem, and should be supervised.

Trichinella spiralis is a parasitic helminth that can infect almost all mammals, including humans. Trichinella spiralis infection elicits a typical type 2 immune responses, while suppresses type 1 immune responses, which is in favour of their parasitism. DNA vaccines have been shown to be capable of eliciting balanced CD4+ and CD8+ T cell responses as well as humoral immune responses in small-animal models, which will be advantage to induce protective immune response against helminth infection. In this study, serine protease (Ts-NBLsp) was encoded by a cDNA fragment of new-born T. spiralis larvae, and was inserted after CMV promoter to construct a DNA vaccine [pcDNA3·1(+)-Ts-NBLsp]. Ts-NBLsp expression was demonstrated by immunofluorescence. Sera samples were obtained from vaccinated mice, and they showed strong anti-Ts-NBLsp-specific IgG response. Mice immunized with the pcDNA3·1(+)-Ts-NBLsp DNA vaccine showed a 77·93% reduction in muscle larvae (ML) following challenge with T. spiralis ML. Our results demonstrate that the vaccination with pcDNA3·1(+)-Ts-NBLsp plasmid promoted the balance of type 1 and 2 immune responses and produced a significant protection against T. spiralis infection in mice.

Based on the finite-differences approach, we study the electronic properties of two-dimensional electron gas under an inhomogeneous magnetic field. Such structure can be realized by deposition of ferromagnetic strips on the surface of a semiconductor heterostructure. It is found that the system exhibits rich band structures. Many bound states are twofold degenerate for θ = π/2, which defines the magnetization direction in the ferromagnetic strips, while few degenerate state exist for θ = 0. Despite of this, there are three kinds of electronic states in our system: the extended, localized and intermediate ones, which is very different from the case of absence of magnetic field.

Plant-mediated interactions between begomoviruses and whiteflies exert important influences on the population dynamics of vectors and the epidemiology of plant diseases. In this article, we synthesize the relevant literature to identify patterns to the interactions. We then review studies on the ecological, biochemical and molecular mechanisms underlying the interactions and finally elaborate on the most interesting issues for future research. The interactions between begomoviruses and the insect vector, the whitefly Bemisia tabaci, via their shared host plants can be mutualistic, neutral or negative. However, in contrast to a pattern of improved performance of vectors on virus-infected plants that has been observed with persistently transmitted RNA viruses, the number of cases exhibiting mutualistic, neutral or negative effects in the indirect interactions between begomoviruses and whiteflies appear evenly distributed. With regard to the mechanisms of plant-mediated positive effects on whiteflies, two case studies indicate that suppression of plant defence and/or alteration in plant nutrition as a result of virus infection can be important. Our review shows that we are only just beginning to understand the tripartite interactions between begomoviruses, whiteflies and plants. Future efforts in this area should try to expand the number and diversity of pathosystems for investigation to reveal the patterns of interactions, to investigate the molecular and biochemical mechanisms of the interactions using a multidisciplinary approach, and to examine the virus–plant–vector interactions in the field and in natural plant communities.

Hyperbranched copper phthalocyanine (CuPc) with uniform spherical morphology has been firstly obtained by ethylene glycol solvothermal synthetic route. The highly dispersed spherical CuPc aggregates with a diameter of ∼500 nm. X-ray diffraction indicated that the molecules were stacked into one-dimensional b-axis aggregate. In addition, the split Soret band together with the broadened and blue-shifted Q-bands in the optical spectra suggested the H (face-to-face) type of interactions in the arrangement of macrocycles in a dense-packed structure. Due to its good symmetrical structure and unique morphology, the hyperbranched spherical CuPc showed excellent broadband microwave absorption behaviors in a frequency of 2–18 GHz. Over an absorber of 5 mm thickness, an absorption bandwidth of 12 GHz corresponding to reflection loss below −10 dB can be obtained. The high value of microwave reflection about −50 dB at the frequency of 16.5 GHz also suggested that the hyperbranched spherical CuPc can be used as promising microwave absorbing materials.

The transport properties of the atomic scale side contact between different metals (Au, Ag, Pt, Cu, Ni, Pd) and graphene with open zigzag ends have been studied from first-principles electron transport calculations. According to the contact configurations, we find the weakly interacting metals (Au, Ag, Pt and Cu) can form chemical bonds at the open graphene’s atomic edges, while the strongly interacting ones form chemical bonds in the whole contact region. Comparing with the case of end contact which could effectively decrease the contact resistance, the atomic scale side contact shows better transport properties than the end contact. And the graphene/metal side contact with hydrogen terminated graphene edge show obviously large resistance than the ones with open graphene edge, which signifies the importance of the termination of graphene edge in graphene/metal contact.