In the soils of western Jilin Province in northeastern China, some significant gaps have been observed between the fraction of the soil existing as clay-size particles (<0.002 mm) and the amount attributable to crystalline clay minerals, and that the relative proportions of crystalline clay minerals to the total clay-size fraction (CP) apparently varies with latitude. The purpose of the present study was to identify the reason for this discrepancy and to explain the dependence on latitude. The grain sizes and mineral compositions of the whole soils from western Jilin Province, China, were analyzed by laser particle-size analysis (LPSA) and X-ray diffraction (XRD), and the <0.002 mm particle-size fraction was analyzed by XRD and X-ray fluorescence (XRF). The results confirmed that the percentage gaps between the clay fraction and clay minerals increased with increasing latitude. The theoretical illite percentage calculated from K2O content was compared with the illite percentage measured by XRD, and the results suggested that the measured illite accounted for only a small proportion of the theoretical illite. Structures of some special minerals below the identification threshold of XRD was suggested to be the reason for the percent gaps. The grain size and mineral crystallization both changed with latitude: the soil particle size and the CP decreased. In addition, clay minerals were more sensitive to climate than particle sizes were, and the CP of clay minerals in the soils within 0~180 cm depth all decreased with increasing latitude; however, the grain size showed patterns with latitude only in relatively shallow soil layers. The present study provides a reference and error analysis for the testing of clay minerals in alpine regions, and more suitable methods may be considered for development of clay-mineral testing in future studies.

The kinetic characteristics of crude oil pyrolysis experiments form the basis for quantitative analysis of shale oil content in Rock-Eval pyrolysis experiments. To study the thermal evaporation kinetics of crude oil in shale, pyrolysis experiments of whole source rock sample and post-extracted sample were carried out on Rock-Eval 6 with the heating rates of 5, 15 and 25°C min−1, respectively. The thermal evaporation of crude oil can be described using a parallel first-order reaction model. A simple method for calculating the kinetic characteristics of the thermal evaporation of extracted crude oil is proposed.

A 1178 J near diffraction limited 527 nm laser is realized in a complete closed-loop adaptive optics (AO) controlled off-axis multi-pass amplification laser system. Generated from a fiber laser and amplified by the pre-amplifier and the main amplifier, a 1053 nm laser beam with the energy of 1900 J is obtained and converted into a 527 nm laser beam by a KDP crystal with 62% conversion efficiency, 1178 J and beam quality of 7.93 times the diffraction limit (DL). By using a complete closed-loop AO configuration, the static and dynamic wavefront distortions of the laser system are measured and compensated. After correction, the diameter of the circle enclosing 80% energy is improved remarkably from 7.93DL to 1.29DL. The focal spot is highly concentrated and the 1178 J, 527 nm near diffraction limited laser is achieved.

Surface molecularly imprinted polymer of solanesol (SA-SMIP) was prepared by reversed phase suspension polymerization using modified titanium dioxide (TiO2) as carrier, and operation conditions were investigated and optimized. Structures of modified TiO2 and SA-SMIP obtained at optimal conditions were characterized by Fourier transform infrared spectrometer adopting original TiO2 and non-surface molecularly imprinted polymer as reference. The SA-SMIP synthesized under optimal conditions displayed an excellent recognition of SA from the mixture of SA and triacontanol. The maximum separation degree of SA was 2.90. Finally, the adsorption kinetics and isotherm were investigated and analyzed. Adsorption kinetics results indicated that the adsorption of SA-SMIP to SA was a pseudo-second order process, and the adsorption of beginning and later stages was controlled by homogeneous particle diffusion and adsorption reaction process, respectively. Adsorption isotherm results documented hereby were two sorts of bonding sites, complete imprinted cavities and defective imprinted cavities. The adsorption for two bonding sites could be well lined up with the Langmuir model.

SG-III laser facility is now the largest laser driver for inertial confinement fusion research in China. The whole laser facility can deliver 180 kJ energy and 60 TW power ultraviolet laser onto target, with power balance better than 10%. We review the laser system and introduce the SG-III laser performance here.

Silicon Carbide (SiC) Metal-Oxide-Semiconductor (MOS) capacitors, having different nitridation times, were characterized by means of Constant Capacitance Deep Level Transient Spectroscopy (CCDLTS). Electron emission was investigated with respect to the temperature dependence of emission rates and the amplitude of the signal as a function of the filling voltage. The comparison between the emission activation energies of the dominant CCDLTS peaks and the filling voltages, led to the conclusion that the dominant trapping behavior originates in the Silicon-dioxide (SiO2) layer. Moreover, a model of electron capture via tunneling can explain the dependence of the CCDLTS signal on increasing filling voltage.

Au contacts were fabricated on pressurized melted grown n-type ZnO single crystal samples pre-treated with boiling organic solvent and hydrogen peroxide. Contacts fabricated without any pre-treatment and with boiling organic solvent pre-treatment were found to have ohmic behavior.For the samples pre-treated with hydrogen peroxide, the Au contacts were found to have rectifying property.Systematic investigation was performed to study the dependence of the Schottky barrier height and the reverse bias leakage current on the temperature and the duration of the pre-treatment.Positron annihilation spectroscopy (PAS), X-ray photoemission (XPS) and scanning electron microscope (SEM) were also used to understand how the vacancy type defect, contamination and surface morphology would influence the electrical property of the fabricated contacts.