Ultrafast optical probing is a widely used method of underdense plasma diagnostic. In relativistic plasma, the motion blur limits spatial resolution in the direction of motion. For many high-power lasers the initial pulse duration of 30–50 fs results in a 10–15 μm motion blur, which can be reduced by probe pulse post-compression. Here we used the compression after compressor approach [Phys.-Usp. 62, 1096 (2019); JINST 17 P07035 (2022)], where spectral broadening is performed in thin optical plates and is followed by reflections from negative-dispersion mirrors. Our initially low-intensity probe beam was down-collimated for a more efficient spectral broadening and higher probe-to-self-emission intensity ratio. The setup is compact, fits in a vacuum chamber and can be implemented within a short experimental time slot. We proved that the compressed pulse retained the high quality necessary for plasma probing.

Echinococcosis poses a significant threat to public health. The Chinese government has implemented prevention and control measures to mitigate the impact of the disease. By analyzing data from the Chinese Center for Disease Control and Prevention and the State Council of the People’s Republic of China, we found that implementation of these measures has reduced the infection rate by nearly 50% between 2004 to 2022 (from 0.3975 to 0.1944 per 100,000 person-years). Nonetheless, some regions still bear a significant disease burden, and lack of detailed information limites further evaluation of the effects on both alveolar and cystic echinococcosis. Our analysis supports the continuing implementation of these measures and suggests that enhanced wildlife management, case-based strategies, and surveillance systems will facilitate disease control.

The chemistry of Al transformation has been well documented, though little is known about the mechanisms of structural perturbation of Al precipitates by carbonates at a molecular level. The purpose of the present study was to investigate the structural perturbation of Al precipitates formed under the influence of carbonates. Initial carbonate/Al molar ratios (MRs) used were 0, 0.1, and 0.5 after aging for 32 days, then the samples were analyzed by X-ray absorption near edge structure spectroscopy (XANES), X-ray diffraction (XRD), Fourier-transform infrared absorption spectroscopy (FTIR), and chemical analysis. The XRD data were in accord with the FTIR results, which revealed that as the carbonate/Al MR was increased from 0 to 0.1, carbonate preferentially retarded the formation of gibbsite and had relatively little effect on the formation of bayerite. As the carbonate/Al MR was increased to 0.5, however, the crystallization of both gibbsite and bayerite was completely inhibited. The impact of carbonate on the nature of Al precipitates was also evident in the increase of adsorbed water and inorganic C contents with increasing carbonate/Al MR. The Al K- and L- edge XANES data provide the first evidence illustrating the change in the coordination number of Al from 6-fold to mixed 6- and 4-fold coordination in the structural network of short-range ordered (SRO) Al precipitates formed under the increasing perturbation of carbonate. The fluorescence yield spectra of the O K-edge show that the intensity of the peak at 534.5 eV assigned to σ* transitions of Al-O and O-H bonding decreased with increasing carbonate/Al MR. The XANES data, along with the evidence from XRD, FTIR, and chemical analysis showed clearly that carbonate caused the alteration of the coordination nature of the Al-O bonding through perturbation of the atomic bonding and structural configuration of Al hydroxides by complexation with Al in the SRO network of Al precipitates. The surface reactivity of an Al-O bond is related to its covalency and coordination geometry. The present findings were, therefore, of fundamental significance in understanding the low-temperature geochemistry of Al and its impacts on the transformation, transport, and fate of nutrients and pollutants in the ecosystem.

As a typical plasma-based optical element that can sustain ultra-high light intensity, plasma density gratings driven by intense laser pulses have been extensively studied for wide applications. Here, we show that the plasma density grating driven by two intersecting driver laser pulses is not only nonuniform in space but also varies over time. Consequently, the probe laser pulse that passes through such a dynamic plasma density grating will be depolarized, that is, its polarization becomes spatially and temporally variable. More importantly, the laser depolarization may spontaneously take place for crossed laser beams if their polarization angles are arranged properly. The laser depolarization by a dynamic plasma density grating may find application in mitigating parametric instabilities in laser-driven inertial confinement fusion.

FFD (free-form deformation method) is one of the most commonly used parameterisation methods at present. It places the parameterised objects inside the control volume through coordinate system transformation, and controls the control volume through control points, thus realising the deformation control of its internal objects. Firstly, this paper systematically analyses and compares the characteristics and technical requirements of Bernstein, B-spline and NURBS (non-uniform rational b-splines) basic functions that can be adopted by FFD, and uses the minimum number of control points required to achieve the specified control effect threshold to express the control capability. Aiming at the problem of discontinuity at the right end in the actual calculation of B-spline basis function, a method of adding a small epsilon is proposed to solve it. Then, three basic functions are applied to the FFD parameterisation method, respectively, and the differences are compared from two aspects of the accurate expression of the model and the ability of deformation control. It is found that the BFFD (b-spline free-form deformation) approach owns better comprehensive performance when the control points are distributed correctly. In this paper, the BFFD method is improved, and a p-BFFD (reverse solution points based BFFD) method based on inverse solution is proposed to realise the free distribution of control points under the specified topology. Further, for the lifting body configuration, the control points of the p-BFFD method are brought closer to the airframe forming the EDGE-p-BFFD (edge constraints based p-BFFD) method. For the case in this paper, the proposed EDGE-p-BFFD method not only has fairly high parameterisation accuracy, but also reduces the expression error from 1.01E-3 to 1.25E-4, which is nearly ten times. It can also achieve effective lifting body guideline constraints, and has the ability of local deformation adapting to the configuration characteristics. In terms of the proportion of effective control points, the EDGE-p-BFFD method increases the proportion of effective control points from 36.7% to 50%, and the more control points, the more obvious the proportion increase effect. The new method also has better effect on the continuity of geometric deformation. At the same time, this paper introduces the independent deformation method of the upper and lower surfaces based on the double control body frames, which effectively avoids the deformation coupling problem of the simultaneous change of the upper and lower surfaces caused by the movement of control points in the traditional single control framework.

The pulsed jet is a novel and effective active mixing enhancement approach. For the transverse pulsed jet in the supersonic crossflow, the frequency influence is investigated using the three-dimensional Reynolds-averaged Navier–Stokes (RANS) equations coupled with the SST k-ω turbulence model. The averaged flow field properties of the pulsed jet are better than those of the steady jet when considering mixing efficiency and jet penetration depth, especially for the case with the pulsed frequency being 50kHz. The flow field structures of the pulsed jet are connected with the time, with periodic wave structures generating in the flow field and moving downstream. The size of the wave structures and its distance are related to the frequency, namely the size and flow distance are relatively small at 50kHz, and it takes some time for the pulsed jet to establish its influence in the full flow field. At low frequencies, the flow field produces large fluctuations, and this may be detrimental to the stable operation of the engine.

Planting patterns have significant effects on rice growth. Nonetheless, little is known about differences in annual crop yield and resource utilization among mechanized rice planting patterns in a rice–wheat cropping system. Field experiments were conducted from 2014 to 2017 using three treatments: pot seedling transplanting for rice and row sowing for wheat (PST-RS), carpet seedling transplanting for rice and row sowing for wheat (CST-RS) and row sowing for both crops (RS-RS). The results showed that, compared with RS-RS, PST-RS and CST-RS prolonged annual crop growth duration by 25–26 and 13–15 days, increased effective accumulated temperature by 399 and 212°C days and increased cumulative solar radiation by 454 and 228 MJ/m2 because of the earlier sowing of rice by 28 and 16 days in PST-RS and CST-RS, respectively. Compared with RS-RS, the annual crop yield of PST-RS and CST-RS increased by 3.1–3.8 and 2.0–2.6 t/ha, respectively, because of the increase in the number of spikelets/kernels per hectare, aboveground biomass, mean leaf area index and grain–leaf ratio. In addition, temperature production efficiency, solar radiation production efficiency and solar radiation use efficiency were higher in PST-RS, followed by CST-RS and RS-RS. These results suggest that mechanized rice planting patterns such as PST-RS increase annual crop production in rice–wheat cropping systems by increasing yield and solar energy utilization.

Unmanned aerial vehicle (UAV) swarm coverage is one of the key technologies for multi-UAV cooperation, which plays an important role in collaborative investigation, detection, rescue and other applications. Aiming at the coverage optimisation problem of UAV in the target area, a collaborative visual coverage control method under positioning uncertainty is presented. First, the visual perception area with imprecise localisation, UAV model and sensor model are created based on the given task environment. Second, a regional division algorithm for the target task area is designed based on the principle of Guaranteed Voronoi (GV) diagram. Then a visual area coverage planning algorithm is designed, in which the task area is allocated to the UAV according to the corresponding weight coefficient of each area, and the input control law is adjusted by the expected state information of the UAV, so that the optimal coverage quality target value and the maximum coverage of the target area can be achieved. Finally, three task scenarios for regional division and coverage planning are simulated respectively, the results show that the proposed area coverage planning algorithm can realise the optimal regional distribution and can obtain more than 90% coverage in different scenarios.

The great demographic pressure brings tremendous volume of beef demand. The key to solve this problem is the growth and development of Chinese cattle. In order to find molecular markers conducive to the growth and development of Chinese cattle, sequencing was used to determine the position of copy number variations (CNVs), bioinformatics analysis was used to predict the function of ZNF146 gene, real-time fluorescent quantitative polymerase chain reaction (qPCR) was used for CNV genotyping and one-way analysis of variance was used for association analysis. The results showed that there exists CNV in Chr 18: 47225201-47229600 (5.0.1 version) of ZNF146 gene through the early sequencing results in the laboratory and predicted ZNF146 gene was expressed in liver, skeletal muscle and breast cells, and was amplified or overexpressed in pancreatic cancer, which promoted the development of tumour through bioinformatics. Therefore, it is predicted that ZNF146 gene affects the proliferation of muscle cells, and then affects the growth and development of cattle. Furthermore, CNV genotyping of ZNF146 gene was three types (deletion type, normal type and duplication type) by Real-time fluorescent quantitative PCR (qPCR). The association analysis results showed that ZNF146-CNV was significantly correlated with rump length of Qinchuan cattle, hucklebone width of Jiaxian red cattle and heart girth of Yunling cattle. From the above results, ZNF146-CNV had a significant effect on growth traits, which provided an important candidate molecular marker for growth and development of Chinese cattle.

The extent of the reduction of maize (Zea mays L.) kernel moisture content through drying is closely related to field temperature (or accumulated temperature; AT) following maturation. In 2017 and 2018, we selected eight maize hybrids that are widely planted in Northeastern China to construct kernel drying prediction models for each hybrid based on kernel drying dynamics. In the traditional harvest scenario using the optimal sowing date (OSD), maize kernels underwent drying from 4th September to 5th October, with variation coefficients of 1.0–1.9. However, with a latest sowing date (LSD), drying occurred from 14th September to 31st October, with variation coefficients of 1.3–3.0. In the changed harvest scenario, the drying time of maize sown on the OSD condition was from 12th September to 9th November with variation coefficients of 1.3–3.0, while maize sown on the LSD had drying dates of 26th September to 28th October with variation coefficients of 1.5–3.6. In the future harvest scenario, the Fengken 139 (FK139) and Jingnongke 728 (JNK728) hybrids finished drying on 20th October and 8th November, respectively, when sown on the OSD and had variation coefficients of 2.7–2.8. Therefore, the maize kernel drying time was gradually delayed and was associated with an increased demand for AT ⩾ 0°C late in the growing season. Furthermore, we observed variation among different growing seasons likely due to differences in weather patterns, and that sowing dates impact variations in drying times to a greater extent than harvest scenarios.

Background: Due to limited therapeutic options and potential for spread, carbapenem-resistant Enterobacteriaceae (CRE)-producing New Delhi metallo-β-lactamases (NDMs) are a public health priority. We investigated the epidemiology of NDM-producing CRE reported to the CDC to clarify its distribution and relative prevalence. Methods: The CDC’s Antibiotic Resistance Laboratory Network supports molecular testing of CRE for 5 carbapenemases nationally. Although KPC is the most common carbapenemase in the United States, non-KPC carbapenemases are a growing concern. We analyzed CRE with any of 4 non-KPC plasmid-mediated carbapenemases (NDM, VIM, IMP, or OXA-48 type) isolated from specimens collected from January 1, 2017, through June 30, 2019; only a patient’s first isolate per organism–carbapenemase combination was included. We excluded isolates from specimen sources associated with colonization screening (eg, perirectal). We compared the proportion of NDM-producing CRE to all non-KPC–producing CP-CRE between period A (January to June 2018) and period B (January to June 2019). Health departments and the CDC collected additional exposure and molecular information in selected states to better describe current NDM-producing CRE epidemiology. Results: Overall, 47 states reported 1,013 non–KPC-producing CP-CRE (range/state, 1–109 isolates; median, 11 isolates); 46 states reported 631 NDM-producing CRE (range/state, 1–84; median, 6). NDM-producing CRE increased quarterly from the third quarter of 2018 through the second quarter of 2019; CP-CRE isolates with other non-KPC carbapenemases remained stable (Fig. 1). In period A, 124 of 216 emerging CP-CRE had NDM (57.1%), compared with 255 of 359 emerging CP-CRE (71.0%) during period B (P = .1179). Among NDM-producing CRE, the proportion of Enterobacter spp increased from 10.5% in 2018 to 18.4% in 2019 (P = .0467) (Fig. 2). In total, 18 states reported more NDM-producing CRE in the first 6 months of 2019 than in all of 2018. Connecticut, Ohio, and Oregon were among states that conducted detailed investigations; these 3 states identified 24 NDM-producing CRE isolates from 23 patients in period B. Overall, 5 (21.7%) of 22 patients with history available traveled internationally ≤12 months prior to culture; 17 (73.9%) acquired NDM-producing CRE domestically. Among 15 isolates sequenced, 8 (53.3%) carried NDM-5 (6 E. coli, 1 Enterobacter spp and 1 Klebsiella spp) and 7 (46.7%) carried NDM-1 (6 Enterobacter spp and 1 Klebsiella spp). Species were diverse; no single strain type was shared by >2 isolates. Conclusions: Detection of NDM-producing CRE has increased across the AR Lab Network. Among states with detailed information available, domestic acquisition was common, and no single variant or strain predominated. Aggressive public health response and further understanding of current US NDM-CRE epidemiology are needed to prevent further spread.

Disclosures: None

Funding: None

Fat metabolism is an important and complex biochemical reaction in vivo and is regulated by many factors. Recently, the findings on high expression of fibroblast growth factor-16 (FGF16) in brown adipose tissue have led to an interest in exploring its role in lipogenesis and lipid metabolism. The study cloned the goat’s FGF16 gene 624 bp long, including the complete open reading frame that encodes 207 amino acids. We found that FGF16 expression is highest in goat kidneys and hearts, followed by subcutaneous fat and triceps. Moreover, the expression of FGF16 reached its peak on the 2nd day of adipocyte differentiation (P < 0.01) and then decreased significantly. We used overexpression and interference to study the function of FGF16 gene in goat intramuscular preadipocytes. Silencing of FGF16 decreased adipocytes lipid droplet aggregation and triglyceride synthesis. This is in contrast to the situation where FGF16 is overexpressed. Furthermore, knockdown of FGF16 also caused down-regulated expression of genes associated with adipocyte differentiation including CCAAT enhancer-binding protein beta (P < 0.01), fatty acid-binding protein-2 (P < 0.01) and sterol regulatory element binding protein-1 (P < 0.05), but the preadipocyte factor-1 was up-regulated. At the same time, the genes adipose triglyceride lipase (P < 0.01) and hormone-sensitive lipase (P < 0.05) associated with triglyceride breakdown were highly expressed. Next, we locked the fibroblast growth factor receptor-4 (FGFR4) through the protein interaction network and interfering with FGF16 to significantly reduce FGFR4 expression. It was found that the expression profile of FGFR4 in adipocyte differentiation was highly similar to that of FGF16. Overexpression and interference methods confirmed that FGFR4 and FGF16 have the same promoting function in adipocyte differentiation. Finally, using co-transfection technology, pc-FGF16 and siRNA-FGFR4, siRNA2-FGF16 and siRNA-FGFR4 were combined to treat adipocytes separately. It was found that in the case of overexpression of FGF16, cell lipid secretion and triglyceride synthesis showed a trend of first increase and then decrease with increasing interference concentration. In the case of interference with FGF16, lipid secretion and triglyceride synthesis showed a downward trend with the increase of interference concentration. These findings illustrated that FGF16 mediates adipocyte differentiation via receptor FGFR4 expression and contributed to further study of the functional role of FGF16 in goat fat formation.

Surface waves called meniscus waves often appear in systems that are close to the capillary length scale. Since the meniscus shape determines the form of the meniscus waves, the resulting streaming circulation has features distinct from those caused by other capillary–gravity waves recently reported in the literature. In the present study, we produce symmetric and antisymmetric meniscus shapes by controlling boundary wettability and excite meniscus waves by oscillating the meniscus vertically. The symmetric and antisymmetric configurations produce different surface capillary–gravity wave modes and streaming flow structures. The root-mean-square speed of the streaming circulation increases with the second power of the forcing amplitude in both configurations. The flow symmetry of streaming circulation is retained under the symmetric meniscus, while it is lost under the antisymmetric meniscus. The streaming circulation pattern beneath the meniscus observed in our experiments is qualitatively explained using the method introduced by Nicolás & Vega (Fluid Dyn. Res., vol. 32 (4), 2003, pp. 119–139) and Gordillo & Mujica (J. Fluid Mech., vol. 754, 2014, pp. 590–604).