In response to the requirements for assessing the impact safety of aero-engines, a high-fidelity numerical simulation method based on overset mesh technology for six-degree-of-freedom rigid body motion is proposed. A gas-solid two-phase flow model is established, coupling two types of ice-debris (externally ingested ice and internally delaminated ice) with air, to analyse their behaviour in a dorsal S-shaped inlet with a diffusion ratio of 1.3. Results indicate that the ice-debris entering from the upper region of the entrance section exerts the most significant distortion on the total-pressure at the engine inlet. Additionally, the behaviour of ice-debris is determined by its angle with respect to the incoming flow direction and the shape of ice. Furthermore, although the ice-debris detached from the entrance section poses no immediate threat to the engine, the prolonged acceleration by high-speed airflow, with velocity increments exceeding 45 m/s, results in a higher kinetic energy carried upon impact with the inlet walls. Regarding externally ingested ice-debris, a smaller initial velocity corresponds to a higher probability of impacting the engine, accompanied by a significant increase in velocity. For instance, the irregular ice-debris ingested at an initial velocity of 6 m/s can experience velocity amplification exceeding 590%.

Turbulent flow widely exists in the aerospace field, and it is still challenging to realise the accurate prediction in the numerical simulation. To realise the high-fidelity numerical simulation of compressible turbulent flow, a high-order accurate self-adaptive turbulence eddy simulation (SATES) method is developed on the PHengLEI-HyOrder open-source solver, combining with the high-order accurate weighted compact nonlinear schemes (WCNS). The compressible flow in the subsonic and transonic is numerically simulated, including some typical cases, such as subsonic flow past a circular cylinder and flow past a square cylinder, high-lift configuration DLR-F11, transonic flow around a circular cylinder. The results predicted by the current high-order accurate SATES are in good agreement with the available experimental and numerical data. The present numerical method can also accurately capture the interactions between shock waves and turbulence while accurately simulating flow separation, shear layer instability and large-scale vortex shedding. The results obtained show that the current high-order accurate SATES simulations based on PHengLEI-HyOrder solver can accurately simulate complex turbulent flows with high reliability.

Liouville-type theorems for the steady incompressible Navier–Stokes system are investigated for solutions in a three-dimensional (3-D) slab with either no-slip boundary conditions or periodic boundary conditions. When the no-slip boundary conditions are prescribed, we prove that any bounded solution is trivial if it is axisymmetric or $ru^r$ is bounded, and that general 3-D solutions must be Poiseuille flows when the velocity is not big in $L^\infty$ space. When the periodic boundary conditions are imposed on the slab boundaries, we prove that the bounded solutions must be constant vectors if either the swirl or radial velocity is independent of the angular variable, or $ru^r$ decays to zero as $r$ tends to infinity. The proofs are based on the fundamental structure of the equations and energy estimates. The key technique is to establish a Saint-Venant type estimate that characterizes the growth of the Dirichlet integral of non-trivial solutions.

Species of the genus Corynosoma (Acanthocephala: Polymorphida) mainly parasitize marine mammals and rarely marine birds, and are of veterinary and medical importance due to causing corynosomiasis in wildlife and humans. However, the current knowledge of the mitochondrial genomes and mitogenomic phylogeny of this group remains very insufficient. In the present study, the complete mitochondrial genomes of C. bullosum (von Linstow, 1892) and C. evae Zdzitowiecki, 1984 were sequenced and annotated for the first time. Both mitogenomes comprise 12 protein-coding genes (missing atp8), 22 tRNA genes, and 2 ribosomal RNAs (rrnS and rrnL), plus 2 non-coding regions (NCR1 and NCR2). Corynosoma bullosum has the largest mitogenome (14,879 bp) of any polymorphid species reported so far, while C. evae has the smallest (13,947 bp), except for Sphaerirostris lanceoides (Petrochenko, 1949). Comparative mitogenomic analysis also revealed the presence of distinct discrepancies in A + T content and gene rearrangement across the families Polymorphidae, Centrorhynchidae, and Plagiorhynchidae. Moreover, phylogenetic analyses based on the concatenated amino acid sequences of 12 protein-coding genes strongly supported the monophyly of the order Polymorphida and a close affinity between the families Polymorphidae and Centrorhynchidae in Polymorphida. The present mitogenomic phylogeny provides additional evidence for a sister relationship between the genera Corynosoma and Bolbosoma and demonstrated that C. evae has a closer relationship with C. villosum than C. bullosum in the genus Corynosoma.

The cyst nematodes, subfamily Heteroderinae, are plant pathogens of worldwide economic significance. A new cyst nematode of the genus Cactodera within the Heteroderinae, Cactodera xinanensis n. sp., was isolated from rhizospheres of crops in the Guizhou and Sichuan provinces of southwest China. The new species was characterized by having the cyst with a length/width = 1.3 ± 0.1 (1.1–1.6), a fenestral diameter of 28.1 ± 4.3 (21.3–38.7) μm, vulval denticles present; second-stage juvenile with stylet 21.5 ± 0.5 (20.3–22.6) μm long, tail 59.4 ± 2.0 (55.9–63.8) μm long and hyaline region 28.7 ± 2.7 (25.0–36.3) μm long, lateral field with four incisures; the eggshell with punctations. The new species can be differentiated from other species of Cactodera by a longer tail and hyaline region of second-stage juveniles. Phylogenetic relationships within populations and species of Cactodera are given based on the analysis of the internal transcribed spacer (ITS-rRNA), the large subunit of the nuclear ribosomal RNA (28S-rRNA) D2-D3 region and the partial cytochrome oxidase subunit I (COI) gene sequences here. The ITS-rRNA, 28S-rRNA and COI gene sequences clearly differentiated Cactodera xinanensis n. sp. from other species of Cactodera. A key and a morphological identification characteristic table for the species of Cactodera are included in the study.

The target backsheath field acceleration mechanism is one of the main mechanisms of laser-driven proton acceleration (LDPA) and strongly depends on the comprehensive performance of the ultrashort ultra-intense lasers used as the driving sources. The successful use of the SG-II Peta-watt (SG-II PW) laser facility for LDPA and its applications in radiographic diagnoses have been manifested by the good performance of the SG-II PW facility. Recently, the SG-II PW laser facility has undergone extensive maintenance and a comprehensive technical upgrade in terms of the seed source, laser contrast and terminal focus. LDPA experiments were performed using the maintained SG-II PW laser beam, and the highest cutoff energy of the proton beam was obviously increased. Accordingly, a double-film target structure was used, and the maximum cutoff energy of the proton beam was up to 70 MeV. These results demonstrate that the comprehensive performance of the SG-II PW laser facility was improved significantly.

The unstart phenomenon of supersonic inlets caused by backpressure is dangerous for aircraft during flights because it severely reduces the air mass flow rate through the engine. We used unsteady numerical simulations to evaluate the unstart and restart characteristics of a two-dimensional supersonic inlet during rapid backpressure changes. The effects of the depressurisation time and depressurisation value on the inlet flow characteristics and restart features are discussed. The results show that the depressurisation time affects the restart procedure when the back pressure drops from the inlet unstart value to the normal working state value. When the depressurisation time decreases, it becomes easier for the inlet to restart. However, the inlet cannot restart if the depressurisation time is too long. When the depressurisation time and value were large enough, a short buzz period occurred before the inlet restarted. Both the time and value of depressurisation affected the restart characteristics.

Water fountains (WFs) are thought to represent an early stage in the morphological evolution of circumstellar envelopes surrounding low- and intermediate-mass evolved stars. These objects are considered to transition from spherical to asymmetric shapes. Despite their potential importance in this transformation process of evolved stars, there are only a few known examples. To identify new WF candidates, we used databases of circumstellar OH (1612 MHz) and H2O (22.235 GHz) maser sources, and compared the velocity ranges of the two maser lines. Finally, 41 sources were found to have a velocity range for the H2O maser line that exceeded that of the OH maser line. Excluding known planetary nebulae and after reviewing the maser spectra in the original literature, we found for 11 sources the exceedance as significant, qualifying them as new WF candidates.

Background: Patient with small thalamic infarct may present with a variety of subtle and seemingly disconnected sensory deficits which can be easily missed. Methods: Here we report a case of an 80 years ‘old Chinese female presenting sudden onset persistent sensory symptoms over perioral area and right hand. The patient underwent further investigation with Brain MRI. The patient underwent further investigation with Brain MRI. A literature review was conducted and the patient’s clinical finding was compared with the literature. Results: The patient’s presentation was consistent with clinical manifestation of type 1 Cheiro-Oral syndrome. Brain MRI performed the day after admission revealed small non-hemorrhagic infarction involving the left thalamus. The diagnosis was type 1 cheiro-oral syndrome secondary to left thalamic ischemic stroke. Conclusions: This report highlights both clinical presentations of cheiro-oral syndrome and correlating clinical symptomatology with anatomic localization. It is important for physicians to recognize this rare condition with subtle presentations for complete work-up and definitive treatment.

The spatio-temporal variation of leaf chlorophyll content is an important crop phenotypic trait that is of great significance for evaluating crop productivity. This study used a soil-plant analysis development (SPAD) chlorophyll meter for non-destructive monitoring of leaf chlorophyll dynamics to characterize the patterns of spatio-temporal variation in the nutritional status of maize (Zea mays L.) leaves under three nitrogen treatments in two cultivars. The results showed that nitrogen levels could affect the maximum leaf SPAD reading (SPADmax) and the duration of high SPAD reading. A rational model was used to measure the changes in SPAD readings over time in single leaves. This model was suitable for predicting the dynamics of the nutrient status for each leaf position under different nitrogen treatments, and model parameter values were position dependent. SPADmax at each leaf decreased with the reduction of nitrogen supply. Leaves at different positions in both cultivars responded differently to higher nitrogen rates. Lower leaves (8th–10th positions) were more sensitive than the other leaves in response to nitrogen. Monitoring the SPAD reading dynamic of lower leaves could accurately characterize and assess the nitrogen supply in plants. The lower leaves in nitrogen-deficient plants had a shorter duration of high SPAD readings compared to nitrogen-sufficient plants; this physiological mechanism should be studied further. In summary, the spatio-temporal variation of plant nitrogen status in maize was analysed to determine critical leaf positions for potentially assisting in the identification of appropriate agronomic management practices, such as the adjustment of nitrogen rates in late fertilization.

Frequent freezing injury greatly influences winter wheat production; thus, effective prevention and a command of agricultural production are vital. The freezing injury monitoring method integrated with ‘3S’ (geographic information systems (GIS), global positioning system (GPS) and remote sensing (RS)) technology has an unparalleled advantage. Using HuanJing (HJ)-1A/1B satellite images of a winter wheat field in Shanxi Province, China plus a field survey, crop types and winter wheat planting area were identified through repeated visual interpretations of image information and spatial analyses conducted in GIS. Six vegetation indices were extracted from processed HJ-1A/1B satellite images to determine whether the winter wheat suffered from freezing injury and its degree of severity and recovery, using change vector analysis (CVA), the freeze injury representative vegetation index and the combination of the two methods, respectively. Accuracy of the freezing damage classification results was verified by determining the impact of freezing damage on yield and quantitative analysis. The CVA and the change of normalized difference vegetation index (ΔNDVI) monitoring results were different so a comprehensive analysis of the combination of CVA and ΔNDVI was performed. The area with serious freezing injury covered 0.9% of the total study area, followed by the area of no freezing injury (3.5%), moderate freezing injury (10.2%) and light freezing injury (85.4%). Of the moderate and serious freezing injury areas, 0.2% did not recover; 1.2% of the no freezing injury and light freezing injury areas showed optimal recovery, 15.6% of the light freezing injury and moderate freezing injury areas showed poor recovery, and the remaining areas exhibited general recovery.

The extent of the reduction of maize (Zea mays L.) kernel moisture content through drying is closely related to field temperature (or accumulated temperature; AT) following maturation. In 2017 and 2018, we selected eight maize hybrids that are widely planted in Northeastern China to construct kernel drying prediction models for each hybrid based on kernel drying dynamics. In the traditional harvest scenario using the optimal sowing date (OSD), maize kernels underwent drying from 4th September to 5th October, with variation coefficients of 1.0–1.9. However, with a latest sowing date (LSD), drying occurred from 14th September to 31st October, with variation coefficients of 1.3–3.0. In the changed harvest scenario, the drying time of maize sown on the OSD condition was from 12th September to 9th November with variation coefficients of 1.3–3.0, while maize sown on the LSD had drying dates of 26th September to 28th October with variation coefficients of 1.5–3.6. In the future harvest scenario, the Fengken 139 (FK139) and Jingnongke 728 (JNK728) hybrids finished drying on 20th October and 8th November, respectively, when sown on the OSD and had variation coefficients of 2.7–2.8. Therefore, the maize kernel drying time was gradually delayed and was associated with an increased demand for AT ⩾ 0°C late in the growing season. Furthermore, we observed variation among different growing seasons likely due to differences in weather patterns, and that sowing dates impact variations in drying times to a greater extent than harvest scenarios.

The characteristic traits of maize (Zea mays L.) leaves affect light interception and photosynthesis. Measurement or estimation of individual leaf area has been described using discontinuous equations or bell-shaped functions. However, new maize hybrids show different canopy architecture, such as leaf angle in modern maize which is more upright and ear leaf and adjacent leaves which are longer than older hybrids. The original equations and their parameters, which have been used for older maize hybrids and grown at low plant densities, will not accurately represent modern hybrids. Therefore, the aim of this paper was to develop a new empirical equation that captures vertical leaf distribution. To characterize the vertical leaf profile, we conducted a field experiment in Jilin province, Northeast China from 2015 to 2018. Our new equation for the vertical distribution of leaf profile describes leaf length, width or leaf area as a function of leaf rank, using parameters for the maximum value for leaf length, width or area, the leaf rank at which the maximum value is obtained, and the width of the curve. It thus involves one parameter less than the previously used equations. By analysing the characteristics of this new equation, we identified four key leaf ranks (4, 8, 14 and 20) for which leaf parameter values need to be quantified in order to have a good estimation of leaf length, width and area. Together, the method of leaf area estimation proposed here adds versatility for use in modern maize hybrids and simplifies the field measurements by using the four key leaf ranks to estimate vertical leaf distribution in maize canopy instead of all leaf ranks.

Emergency search and rescue on the sea is an important part of national emergency response for marine perils. Optimal route planning for maritime search and rescue is the key capability to reduce the searching time, improve the rescue efficiency, as well as guarantee the rescue target’s safety of life and property. The main scope of the searching route planning is to optimise the searching time and voyage within the constraints of missing search rate and duplicate search rate. This paper proposes an optimal algorithm for searching routes of large amphibious aircraft corresponding to its flight characteristics and sea rescue capability. This algorithm transforms the search route planning problem into a discrete programming problem and applies the route traceback indexes to satisfy the duplicate search rate and missing search rate.

An acute gastroenteritis (AGE) outbreak caused by a norovirus occurred at a hospital in Shanghai, China, was studied for molecular epidemiology, host susceptibility and serological roles. Rectal and environmental swabs, paired serum samples and saliva specimens were collected. Pathogens were detected by real-time polymerase chain reaction and DNA sequencing. Histo-blood group antigens (HBGA) phenotypes of saliva samples and their binding to norovirus protruding proteins were determined by enzyme-linked immunosorbent assay. The HBGA-binding interfaces and the surrounding region were analysed by the MegAlign program of DNAstar 7.1. Twenty-seven individuals in two care units were attacked with AGE at attack rates of 9.02 and 11.68%. Eighteen (78.2%) symptomatic and five (38.4%) asymptomatic individuals were GII.6/b norovirus positive. Saliva-based HBGA phenotyping showed that all symptomatic and asymptomatic cases belonged to A, B, AB or O secretors. Only four (16.7%) out of the 24 tested serum samples showed low blockade activity against HBGA-norovirus binding at the acute phase, whereas 11 (45.8%) samples at the convalescence stage showed seroconversion of such blockade. Specific blockade antibody in the population played an essential role in this norovirus epidemic. A wide HBGA-binding spectrum of GII.6 supports a need for continuous health attention and surveillance in different settings.

Stratospheric airships are promising aircraft, usually designed as a non-rigid airship. As an essential part of the non-rigid airship, the envelope plays a significant role in maintaining its shape and bearing the external force load. Generally, the envelope material of a flexible airship consists of plain-weave fabric, composed of warp and weft fibre yarn. At present, biaxial tensile experiments are the primary method used to study the stress–strain characteristics of such flexible airship materials. In this work, biaxial tensile testing of UN-5100 material was carried out. The strain on the material under unusual stress and the stress ratio were obtained using Digital Image Correlation (DIC) technology. Also, the stress–strain curve was corrected by polynomial fitting. The slope of the stress–strain curve at different points, the Membrane Structures Association of Japan (MSAJ) standard and the Radial Basis Function (RBF) model were compared to identify the stress–strain characteristics of the materials. Some conclusions on the mechanical properties of the flexible airship material can be drawn and will play a significant role in the design of such envelopes.