Based on a 4f system, a 0° reflector and a single laser diode side-pump amplifier, a new amplifier is designed to compensate the spherical aberration of the amplified laser generated by a single laser diode side-pump amplifier and enhance the power of the amplified laser. Furthermore, the role of the 4f system in the passive spherical aberration compensation and its effect on the amplified laser are discussed in detail. The results indicate that the amplification efficiency is enhanced by incorporating a 4f system in a double-pass amplifier and placing a 0° reflector only at the focal point of the single-pass amplified laser. This method also effectively uses the heat from the gain medium (neodymium-doped yttrium aluminium garnet) of the amplifier to compensate the spherical aberration of the amplified laser.

Stimulated Raman scattering is a third-order nonlinear optical effect that is not only effective for wavelength converting laser output, but also for single longitudinal-mode output due to the absence of spatial hole burning. Diamond is a prominent Raman-active medium that has significant potential for linewidth narrowing and wavelength converting lasers at high power levels due to its high thermal conductivity, long Raman frequency shift and wide spectral transmission range. In this work we utilize diamond in a resonantly mode-matched external cavity to achieve cascaded Raman conversion of a 1064 nm laser. By fine-tuning the length of this external cavity, we can obtain narrow linewidth emission at 1240 and 1485 nm. When operating at maximum power, the measured linewidths were more than twofold narrower than the linewidth of the fundamental field. In addition, the noise levels of the Stokes fields are lower than that of the fundamental field throughout the entire noise frequency range, and the intrinsic linewidth of the second Stokes field, which is expressed at the hertz level (~3.6 Hz), is decreased by approximately three orders of magnitude compared to that of the pump. This work represents the first measurement and analysis of the linewidth and noise characteristics of cascaded diamond Raman lasers and, significantly, offers a new means by which high-power, narrow linewidth laser output can be produced from wavelength-converted laser systems.

A continuous-wave (CW) single-longitudinal-mode (SLM) Raman laser at 1240 nm with power of up to 20.6 W was demonstrated in a free-running diamond Raman oscillator without any axial-mode selection elements. The SLM operation was achieved due to the spatial-hole-burning free nature of Raman gain and was maintained at the highest available pump power by suppressing the parasitic stimulated Brillouin scattering (SBS). A folded-cavity design was employed for reducing the perturbing effect of resonances at the pump frequency. At a pump power of 69 W, the maximum Stokes output reached 20.6 W, corresponding to a 30% optical-to-optical conversion efficiency from 1064 to 1240 nm. The result shows that parasitic SBS is the main physical process disturbing the SLM operation of Raman oscillator at higher power. In addition, for the first time, the spectral linewidth of a CW SLM diamond Raman laser was resolved using the long-delayed self-heterodyne interferometric method, which is 105 kHz at 20 W.

Developmental signals and environmental stresses regulate carbon distribution in the vegetative and reproductive organs of plants and affect seed yield. Cleistogenes songorica is a xerophytic grass with great potential application value in ecological restoration. However, how carbohydrate transport and distribution during grain filling affect the seed yield of C. songorica under water stress is not clear. The present study showed that the soluble sugar and starch contents of cleistogamous (CL) spikes and chasmogamous (CH) spikes were significantly higher at the milk stage, which was attributed to a significantly higher seed number and seed yield per spike under water stress conditions than under well-watered conditions (P < 0.01). RNA-seq data revealed a total of 54,525 differentially expressed genes (DEGs) under water stress conditions, but only 3744 DEGs were shared among all comparison groups. Weighted gene co-expression network analysis showed that the transport and distribution of carbohydrates were regulated by ABA-responsive genes (CsABA8OX1_1, CsABA8OX1_2, CsABA8OX2_1, CsABA8OX2_2, CsNCED3, CsNCED1_1, CsNCED1_2 and CsNCED4_1) and sugar transport and starch synthesis genes (CsSUS1, CsSUS2, CsSUS3, CsAGP1, CsAGP4, CsAGP5, CsSSS1 and CsSBE5) under water stress conditions. These genes jointly regulated carbohydrate remobilization in sources (stems, leaves and sheaths) to promote grain filling and improve seed yield. The present study helped to clarify the phenotypic, metabolic and transcriptional response mechanisms of vegetative organs, such as stems and leaves, and reproductive organs, such as CL spikes and CH spikes, to promote carbohydrate redistribution under water stress, and it provides theoretical guidance for improving seed yields.

The commercial Computational Fluid Dynamics (CFD) software STAR-CCM+ was used to simulate the flow and breakup characteristics of a Liquid Jet Injected into the gaseous Crossflow (LJIC) under real engine operating conditions. The reasonable calculation domain geometry and flow boundary conditions were obtained based on a civil aviation engine performance model similar to the Leap-1B engine which was developed using the GasTurb software and the preliminary design results of its low-emission combustor. The Volume of Fluid (VOF) model was applied to simulate the breakup feature of the near field of LJIC. The numerical method was validated and calibrated through comparison with the public test data at atmospheric conditions. The results showed that the numerical method can capture most of the jet breakup structure and predict the jet trajectory with an error not exceeding ±5%. The verified numerical method was applied to simulate the breakup of LJIC at the real engine operating condition. The breakup mode of LJIC was shown to be surface shear breakup at elevated condition. The trajectory of the liquid jet showed good agreement with Ragucci’s empirical correlation.

The core toroidal plasma intrinsic rotation has been studied by experiments and simulations in the Joint Texas Experimental Tokamak (J-TEXT). The direction of core intrinsic rotation in the J-TEXT plasma is counter-current. As the plasma density ramps up, the rotation velocity increases in the counter-current direction. By comparing four different electron densities, linear local gyrokinetic simulations have been performed by the Gyrokinetic Electromagnetic Numerical Experiment code for the first time on J-TEXT. It is found that the most dominant turbulence is the ion temperature gradient at $0.2a$, where $a$ is the minor radius of the plasma and this is unchanged during the plasma density ramp up. By scanning the radial wave vectors, it is found that the residual stress term reverses from negative to positive when the plasma density exceeds a certain threshold. The pinch term is larger than the residual stress term at all four electron densities, which means that the pinch term is always dominant in the core of a J-TEXT plasma.

Minimally invasive surgery is a developing direction of modern medicine. With the successful development of controllable capsule endoscopies, capsule robots are very popular in the field of gastrointestinal medicine. At present, the study of intestinal robots is aimed at the pipeline environment of a single-phase liquid flow. But there exist food residues (i.e. solid particles) or liquid foods in the actual intestine, so intestinal fluid should be liquid–solid or liquid–liquid two-phase mixed fluid. For inner spiral capsule robots with different internal diameters and outer spiral capsule robots, using computational fluid dynamics (CFD) method, the operational performance indicators (i.e. axial thrust force, circumferential resisting moment and maximum pressure to pipeline wall) of spiral capsule robots are numerically calculated in the liquid–solid or liquid–liquid two-phase mixed fluid. By the orthogonal experimental optimization method, the optimum design of spiral capsule robots is obtained in the liquid–solid mixed fluid. The experimental verification has been also carried out. The results show that in the liquid–solid two-phase fluid, the axial thrust force and circumferential resisting moment of the spiral capsule robots decrease with the increase of the size or concentration of solid particles. In the same liquid–solid or liquid–liquid mixed fluid, the operational performance indicators of outer spiral robots are much higher than those of inner spiral robots, and the operational performance indicators of inner spiral robots with bigger internal diameters are higher than those with smaller internal diameters. Adding solid particles of high concentration in the pipeline containing liquid will reduce the drive performance of spiral capsule robots, but adding another liquid of high viscosity will improve the drive performance of spiral capsule robots.

The endoparasitoid Microplitis prodeniae Rao and Chandry is an important potential augmentative biological control agent for lepidopteran pests of vegetables and tobacco. However, cold storage of pupae is required to ensure that sufficient parasitoids are available when they are needed in the field. In this study, pupae were maintained at 0, 4 or 10°C for 5–50 days after which the adults were evaluated for emergence, pre-emergence period, sex ratio, female longevity, oviposition period, and fecundity. Cold storage did not affect the pre-emergence period or proportion of females; however, there was a significant reduction in emergence, female longevity, oviposition period, and fecundity with increased exposure to cold. The pre-emergence period was approximately 5 days, and approximately 50% of the emergent parasitoids were females. A cold storage regime of 10 days at 10°C had no effect on the parasitoids and adult emergence was greater than 50% even after 20 days at 10°C. There was no carryover of the cold treatment from parental to F1 and F2 generations. Thus, M. prodeniae can be stockpiled for field release by exposing the pupae to a cold regime and subsequently holding them for adult emergence at 28°C.

With increasing output of petroleum coke, the value-added exploitation of petroleum coke has become a tough problem. Preparing porous carbons is a traditional way to the value-added exploitation of petroleum coke. Here, we used a facile and efficient hard-templating strategy to synthesize mesoporous carbon with high surface area from petroleum coke. N2 adsorption analyses show that the BET specific area and pore volume of the carbons can reach up to 864 m2/g and 1.37 cm3/g, respectively. To utilize the abundant mesopores of the carbons, anthraquinone-modified mesoporous carbon was tested as an electrode material for supercapacitor applications. Electrochemical measurements demonstrated that the specific capacitance reached up to 366 F/g at the current density of 1 A/g, indicating a promising prospect of using this carbon in electrochemical energy-storage field. More importantly, the strategy used in this work can be easily modified to prepare other nano-carbon materials from petroleum coke.

A novel micro in-pipe robot using an internally threaded profile for propulsion is proposed in this paper, and the dynamic model of the robot in the turbulent liquid pipeline is established, and the computational fluid dynamics method is used to solve the influence of environmental parameters and operating parameters on the robotic performance. By the orthogonal experimental optimization method, the optimal inner spiral structural parametrical combination is obtained. According to the working principle of the inner spiral robot, an inner spiral driving device is designed and fabricated, and the running experiment in the pipeline full of 201 methyl silicone oil verifies the feasibility of the proposed robot. Adopting the pulsating blood flow function as the inlet condition, in a pulsating period, the robotic performance is numerically analyzed.

The present study was conducted to test the hypothesis that low concentrations of coated ZnO, as a substitute for a high concentration of ZnO (2250 mg Zn/kg), could improve intestinal immunity function and regulate microbiota composition, thus alleviating the incidence of diarrhoea in weaned piglets. A total of eighty-four cross-bred piglets, weaned at an age of 28 (sem 1) d, were allocated randomly, on the basis of average initial body weight (7·72 (sem 0·65) kg), to seven treatment groups as follows: a 250 mg Zn (ZnO)/kg group (low Zn; LZ) and a 2250 mg Zn (ZnO)/kg group (high Zn; HZ) that were offered diets containing ZnO at 250 and 2250 mg Zn/kg, respectively; and five experimental groups in which coated ZnO was added at 250, 380, 570, 760 and 1140 mg Zn/kg basal diet, respectively. The trial lasted 2 weeks. The results indicated that, compared with LZ treatment, supplementation with coated ZnO at 380 or 570 mg Zn/kg reduced (P< 0·05) diarrhoea index, increased (P< 0·05) duodenal villus height and the ratio of villus height:crypt depth, up-regulated (P< 0·05) the gene expression of insulin-like growth factor 1, zonula occludens protein-1, occludin, IL-10 and transforming growth factor β1, and elevated (P< 0·05) secretory IgA concentration in the jejunal mucosa. Microbiota richness and the Shannon diversity index were also decreased (P< 0·05). Furthermore, piglets in the group fed coated ZnO at 380 or 570 mg Zn/kg did not differ from those in the HZ-fed group in relation to the aforementioned parameters. Collectively, a low concentration of coated ZnO (380 or 570 mg Zn/kg) can alleviate the incidence of diarrhoea by promoting intestinal development, protecting the intestinal mucosal barrier from damage, stimulating the mucosal immune system and regulating the microbiota composition.

Kashin-Beck disease (KBD) is a chronic endemic osteoarthropathy, which mainly occurs in West and Northeast China. Epidemiological studies suggest that Se deficiency is an important environmental factor for the incidence of KBD. Glutathione peroxidase 4 (GPx4) belongs to the glutathione peroxidase family, which is crucial for optimal antioxidant defences. Our purpose is to investigate the putative association between GPx4 polymorphisms and the risk of KBD. Restriction fragment length polymorphism-PCR was used to detect two SNP (rs713041, rs4807542) in 219 cases and 194 controls in Han Chinese subjects, and quantitative analysis for the GPx4 mRNA level was performed by the real-time PCR method. The results revealed that linkage disequilibrium existed in the two SNP. A significant difference was observed in the haplotype A-T (P = 0·0066) of GPx4, which was obviously lower in the KBD cases (0·006 v. 0·032 %). Correlation analysis based on a single locus showed no association between each SNP and KBD risk. Furthermore, the GPx4 mRNA level was dramatically lower in the blood of KBD patients. Overall, our finding indicated GPx4 polymorphisms and decreased mRNA level may be related to the development of KBD in the Chinese population, suggesting GPx4 as a possible candidate susceptibility gene for KBD.

Mg-Li-Al alloy was prepared by ingot casting and then underwent subsequent reactive ball milling. A Mg-Li-Al-H complex hydride was obtained under a 0.4 MPa hydrogen atmosphere at room temperature, and as high as 10.7 wt% hydrogen storage capacity was achieved, with the peak desorption temperature of the initial step at approximately 65 °C. The evolution of the reaction during milling, as well as the effect of Li/Al ratio in the raw materials on the desorption properties of the hydrides formed, were studied by x-ray diffraction and simultaneous thermogravimetry and differential scanning calorimetry techniques. The results showed that mechanical milling increases the solubility of Li in Mg, leading to the transformation of bcc β(Li) solid solution to hcp α(Mg) solid solution, the latter continues to incorporate Li and Al, which stimulates the formation of Mg-Li-Al-H hydride. A lower Li/Al ratio resulted in faster hydrogen desorption rate and a greater amount of hydrogen released at a low temperature range, but sacrificing total hydrogen storage capacity.

The techniques used to detect genetically modified organisms (GMO), including qualitative polymerase chain reaction (PCR), quantitative PCR, enzyme-linked immunosorbent assay (ELISA) and many others, are systematically described and discussed. The application progress of GMO in species-specific detection, endogenous genes, standard substances and restraining factors influencing detection are reviewed. The ongoing problems and development prospects of detection techniques of GMO are also pointed out.