Nanocrystalline (NC) and ultrafine-grained (UFG) CoCrCuFeNi high-entropy alloy (HEA) with grain size ranging between 59 and 386 nm was produced via powder metallurgy and heat treatment. The as-sintered HEA exhibited two face-centered cubic (FCC) phases (CoCrFeNi-rich and Cu-rich phases) and a small grain size (59 nm), whereas the alloy after heat treatment at 1000 °C exhibited a CoCuFeNi-rich phase with FCC structure and relatively larger grain size (386 nm). Moreover, the yield strength decreased from 1930 to 883 MPa, and plastic strain to failure increased by 8–32%. In terms of microstructural evolution, grain boundary strengthening coupled with lattice distortion was the dominant strengthening mechanism for NC HEAs. Furthermore, the coefficient for boundary strengthening was higher in the HEAs than in the corresponding pure elemental metals with FCC structure, possibly because of significant lattice distortion. The UFG HEAs exhibited high strength and good ductility because of the activation of dislocation.

To evaluate the appropriateness of the screening strategy for healthcare personnel (HCP) during a hospital-associated Middle East Respiratory Syndrome (MERS) outbreak, we performed a serologic investigation in 189 rRT-PCR–negative HCP exposed and assigned to MERS patients. Although 20%–25% of HCP experienced MERS-like symptoms, none of them showed seroconversion by plaque reduction neutralization test (PRNT).

Infect Control Hosp Epidemiol 2017;38:234–238

The development of embryonic stem cells (ESCs) from large animal species has become an important model for therapeutic cloning using ESCs derived by somatic cell nuclear transfer (SCNT). However, poor embryo quality and blastocyst formation have been major limitations for derivation of cloned ESCs (ntESCs). In this study, we have tried to overcome these problems by treating these cells with histone deacetylase inhibitors (HDACi) and aggregating porcine embryos. First, cloned embryos were treated with Scriptaid to confirm the effect of HDACi on cloned embryo quality. The Scriptaid-treated blastocysts showed significantly higher total cell numbers (29.50 ± 2.10) than non-treated blastocysts (22.29 ± 1.50, P < 0.05). Next, cloned embryo quality and blastocyst formation were analyzed in aggregates. Three zona-free, reconstructed, four-cell-stage SCNT embryos were injected into the empty zona of hatched parthenogenetic (PA) blastocysts. Blastocyst formation and total cell number of cloned blastocysts increased significantly for all aggregates (76.4% and 83.18 ± 8.33) compared with non-aggregates (25.5% and 27.11 ± 1.67, P < 0.05). Finally, aggregated blastocysts were cultured on a feeder layer to examine the efficiency of porcine ES-like cell derivation. Aggregated blastocysts showed a higher primary colony formation rate than non-aggregated cloned blastocysts (17.6 ± 12.3% vs. 2.2 ± 1.35%, respectively, P < 0.05). In addition, derived ES-like cells showed typical characters of ESCs. In conclusion, the aggregation of porcine SCNT embryos at the four-cell stage could be a useful technique for improving the development rate and quality of porcine-cloned blastocysts and the derivation efficiency of porcine ntESCs.

During the past decade, carbapenemase-producing Enterobacteriaceae (CPE) has emerged and spread across the world.1 The major carbapenemase enzymes currently being reported are KPC, NDM-1, VIM, IMP, and OXA.2 Because carbapenemase can be effectively transmitted via mobile genetic elements, and current therapeutic options for CPE infections are extremely limited, CPE may be one of the most serious contemporary threats to public health. However, very little is known about the characteristics of CPE carriage during hospitalization. The aims of this study were to investigate the clearance rate of CPE carriage and determine the number of consecutive negative cultures required to confirm CPE clearance. We also examined CPE transmission among hospitalized patients.

Infect. Control Hosp. Epidemiol. 2015;36(11):1361–1362

We report the demonstration of low power phase change memory (PCM) by forming thin self-assembled SiOx nanostructures between Ge2Sb2Te5 (GST) and a TiN heater layer utilizing a block copolymer (BCP) self-assembly technology. The reset current was decreased about three-fold as fill factor, which is the occupying area fraction of self-assembled SiOx nanostructures on a TiN heater layer, increased to 75.3%. The electro-thermal simulation shows the better heat efficiency due to the nano-patterned insulating oxide.

We present a rapid and sensitive surface acoustic wave (SAW) immunosensor that utilizes gold staining as a signal enhancement method. A sandwich immunoassay was performed on sensing area of the SAW sensor, which could specifically capture and detect cardiac markers (cardiac troponin I (cTnI), creatine kinase (CK)-MB, and myoglobin). The analytes in human serum were captured on gold nanoparticles (AuNPs) that were conjugated in advance with detection antibodies. Introduction of these complexes to the capture antibody-immobilized sensor surface resulted in a classic AuNP-based sandwich immunoassay format that has been used for signal amplification. In order to achieve further signal enhancement, a gold staining method was performed, which demonstrated that it is possible to obtain gold staining-mediated signal augmentation on a mass-sensitive device. The sensor response due to gold staining varied as a function of cardiac marker concentration.

Background: The influences of demographics, culture, language, and environmental changes on Mini-Mental State Examination (MMSE) scores are considerable.

Methods: Using a sample of 7452 healthy, community-dwelling elderly Koreans, aged 55 to 94 years, who participated in the four ongoing geriatric cohorts in Korea, we investigated demographic influences on MMSE scores and derived normative data for this population. Geropsychiatrists strictly excluded subjects with cognitive disorders according to the protocol of the Korean version of the Consortium to Establish a Registry for Alzheimer's Disease Assessment Packet (CERAD-K) Clinical Assessment Battery (CERAD-K-C).

Results: Education (standardized β = 0.463), age (standardized β = −0.303), and gender (standardized β = −0.057) had significant effects on MMSE scores (p < 0.001). The score of MMSE increase 0.379 point per 1-year education, decrease 0.188 per 1-year older, and decrease 0.491 in women compared to men. Education explained 30.4% of the scores’ total variance, which was much larger than the variances explained by age (8.4%) or gender (0.3%). Accordingly, we present normative data for the MMSE stratified by education (0, 1–3, 4–6, 7–9, 10–12, and ≥ 13 years), age (60–69, 70–79, and 80–89 years), and gender.

Conclusions: We provide contemporary education-, age-, and gender-stratified norms for the MMSE, derived from a large, community-dwelling elderly Korean population sample, which could be useful in evaluating individual MMSE scores.

This paper provides an overview of the development and application of the National Aquatic Ecological Monitoring Program (NAEMP) in Korea, which uses biological and habitat–riparian criteria for river/stream and watershed management. Development of NAEMP began in 2003, with recognition by the Korean Ministry of Environment (MOE) of the limitations of applying chemical parameters (e.g., biochemical oxygen demand (BOD)) as the principal targets of water environment management. Ecosystem health criteria under NAEMP were developed from 2003 to 2006. Candidate sites for monitoring were also screened and established across the country. NAEMP was implemented in 2007, and since then a standard protocol of nationwide monitoring based on multi-criteria has been implemented to assess the ecological condition of rivers and streams. The monitoring results indicate that many Korean rivers and streams are severely degraded, with biological conditions that are much worse than their water chemistry suggests. In 2009, 24% of rivers and streams were in classes C (Fair) and D (Poor) for BOD, but more than 71, 53, and 27% were categorized as Fair to Poor according to fish, diatom, and benthic macroinvertebrate assemblages, respectively. NAEMP is promising in that the results have already had great impacts on policy making and scientific research relevant to lotic water environment and watershed management in Korea. In the future, NAEMP results will be used to develop more aggressive regulations for the preservation and restoration of rivers/streams, riparian buffer areas and watersheds. Another future aim of the NAEMP is to develop aquatic ecological modeling based on the monitoring results.

Pt thin films of various thicknesses (30 nm ∼ 200 nm) were deposited on Si wafers with SiO2, Ti, TiO2, or IrO2 buffer layers at various temperatures (room temperature ∼200 °C) by a direct current magnetron sputtering process. The Pt films showed a strong (111)-preferred texture irrespective of the thickness, under-layer, and growth temperature. The authors previously reported [J-E. Lim, D-Y. Park, J.K. Jeong, G. Darlinski, H.J. Kim, and C.S. Hwang, Appl. Phys. Lett. 81, 3224 (2002)] that the films were composed of three kinds of grains with slightly different (111) lattice parameters (bulklike, 1.0% and 2.1% larger). This study details the microstructural variations of the Pt films according to the variations of experimental parameters. The different deposition conditions produced slightly different crystalline structures, but the three different (111) lattice parameters were always found. Epitaxial (200) Pt films on a (200) MgO substrate and a highly (111) textured Au thin film on a SiO2/Si did not show the same splitting in the lattice parameter. The grains with 1.0% and 2.1% larger (111) lattice parameter almost disappeared after postannealing at 1000 °C. However, surface chemical binding of the Pt film before and after annealing was unchanged. Therefore, it is believed that the lattice parameter splitting in the (111) textured Pt film originated from the interfacial grains with the distorted crystal structure due probably to growth stress.

Bilayer structures consisting of ZrO2-3mol% Y2O3(TZ-3Y) and zirconia-alumina composites as inner (substrate) and outer (coating) layers, respectively, are fabricated using gel-casting for the inner layer and dip-coating for the outer layer in aqueous system. The relatively tough TZ-3Y is used as the inner layer for damage absorption due to its mechanical properties. The mixture ratio of alumina/zirconia slips for dip-coating is 1:9, 2:8, and 3:7 as mole ratio. The processing additives for gel casting, such as dispersant, monomer, dimer, and initiator, are adjusted and optimized by measuring viscosity. From which the solid loading of starting material (TZ-3Y) is determined. The optimum amount of dispersant (D-3019; anionic dispersant agent) for TZ-3Y is 0.7 wt%. The slip pH affects the electric double layer in sols, which causes the different rheological behaviors and solid loadings. The castable solid loading of TZ-3Y is 37 vol%, showing a pseudoplastic rheological behavior. The effect of slip type (different mixture ratio) on sintered body is investigated through hardness (Vickers indentation), microstructure (SEM), and strength (4-point bending tests). Strength of sintered bodies after dip-coating into the slips is higher than that before dip-coating, but hardness is not much different among cases. The effects of thickness in the outer layer on damage resistance and mechanical properties of the bilayer structures are discussed extensively.

We report the role of thin AlN interlayer in the fabrication of AlxGa1-xN/GaN heterostructures with high x from 0.35 to 0.50 on sapphire (0001) by MOVPE. After growing the AlN interlayer of 20 nm thick on GaN/sapphire (0001) epitaxy, the AlxGa1-xN epitaxial layers of 1.0 um thick were grown on it with increasing the flow rate of TMA. The measured Al mole fractions of AlxGa1-xN/GaN heteroepitaxy grown using the thin AlN interlayer from each TCD rocking curve are 0.35, 0.37, 0.45 and 0.50, respectively. As incorporation rate of Al in the AlxGa1-xN increases, the crystallinity is getting well and the RMS values scanned by AFM of their surfaces become lower. And also, the optoelectronic characteristics of those heteroepitaxy evaluated by cathodeluminescence(CL) are improved with the increase of x. To the contrary these trends, it is usually known that crystallinity, surface morphology and optical property of the AlxGa1-xN/GaN heteroepitaxy grown without AlN interlayer between them become worse with the increase of x above 0.2. Meanwhile, electrical resisitivities of Al0.35Ga0.65N, Al0.37Ga0.63N, Al0.45Ga0.55N and Al0.50Ga0.50N epitaxy, which were grown with the thin AlN interlayer, measured by four point probing method are 13.5, 18.1, 31.7 and 36.2 Mohm-cm, respectively. These resisitivities increase by degrees in spite of the advance of characteristics with the raising of x.