A systematic characterization of a less known Al, Fe, Mn, and Si phase in a SiC particulate-reinforced 2014Al composite (SiCp/2014Al) was performed. In addition to the expected CuAl2 phase, the Al, Fe, Mn, and Si phase was formed as either an adhesion (>1 µm) onto SiC in the as-cast composite, or as a precipitate (<100 nm) in the matrix after hot extrusion. The structure of the phase was identified as cubic by both X-ray diffraction and selected area electron diffraction (SAED). The SAED pattern also indicated that the structure belongs to the Pm $\bar{3}$ space group instead of Im $\bar{3}$ . The thermodynamic phase diagram was calculated, confirming the presence of an α-AlFeMn or α-AlFeSi phase in the Al–Fe–Mn and Al–Fe–Si ternary systems, respectively, within the Fe, Mn, and Si content range corresponding to 2014Al. Wavelength-dispersive spectroscopy analysis indicated that the composition of the phase is close to Al12(Fe, Mn)3Si2, in which the Mn/Fe ratio is in the range of 0.6–1.4. The determined Mn/Fe ratio corresponds to the nominal composition of Mn and Fe in the alloy.

Paediatric Mycoplasma pneumoniae pneumonia (MPP) is a major cause of community-acquired pneumonia in China. Data on epidemiology of paediatric MPP from China are little known. This study retrospectively collected data from June 2006 to June 2016 in Beijing Children's Hospital, Capital Medical University of North China and aims to explore the epidemiological features of paediatric MPP and severe MPP (SMPP) in North China during the past 10 years. A total of 27 498 paediatric patients with pneumonia were enrolled. Among them, 37.5% of paediatric patients had MPP. In this area, an epidemic took place every 2–3 years at the peak, and the positive rate of MPP increased during these peak years over time. The peak age of MPP was between the ages of 6 and 10 years, accounting for 75.2%, significantly more compared with other age groups (χ2 = 1384.1, P < 0.0001). The epidemics peaked in September, October and November (χ2 = 904.9, P < 0.0001). Additionally, 13.0% of MPP paediatric patients were SMPP, but over time, the rate of SMPP increased, reaching 42.6% in 2016. The mean age of paediatric patients with SMPP (6.7 ± 3.0 years old) was younger than that of patients with non-SMPP (7.4 ± 3.2 years old) (t = 3.60, P = 0.0001). The prevalence of MPP and SMPP is common in China, especially in children from 6 to 10 years old. Paediatric patients with SMPP tend to be younger than those with non-SMPP. MPP outbreaks occur every 2–3 years in North China. September, October and November are the peak months, unlike in South China. Understanding the epidemiological characteristics of paediatric MPP can contribute to timely treatment and diagnosis, and may improve the prognosis of children with SMPP.

In this work, carbon nanotubes (CNTs)-templated binuclear metallophthalocyanines (MTAPcCF3)2C (M = Mn, Fe, Co, Ni, Cu, Zn) assemblies (MTAPcCF3)2C–COOH–CNTs are designed and obtained. Whereafter, the structure and morphology of target products are analyzed by many means such as infrared, X-ray diffraction, X-ray photoelectron spectroscopy, and scanning electron microscopy. The electrocatalytic performances of lithium-thionyl chloride battery catalyzed by (MTAPcCF3)2C–COOH–CNTs were carried out. The result shows that all catalysts can improve the battery performance including the discharge time and the initial voltage. The catalytic performance of (MTAPcCF3)2C–COOH–CNTs is ordered following the central metal: Mn > Fe > Ni > Co > Cu > Zn. The cell capacity catalyzed by optimal catalyst (MnTAPcCF3)2C–COOH–CNTs can expand to 28.08 mAˑh, with increase by 142.07%, and the (MnTAPcCF3)2C–COOH–CNTs can extend the discharge time to 551.6 s. Besides, the reaction mechanism is presented on the basis of cyclic voltammetry measurements.

Monosized spherical Cu–20% Sn (wt%) alloy particles with diameter ranging from 70.6 to 334.0 μm were prepared by the pulsated orifice ejection method (termed “POEM”). Fully dense without pores and bulk inclusions, the cross-sectional micrographs of the spherical alloy particles indicate an even distribution of Cu and Sn. These spherical Cu–Sn alloy particles exhibit a good spherical shape and a narrow size distribution, suggesting that the liquid Cu–Sn alloy can completely break the balance between the surface tension and the liquid static pressure in the crucible micropores and accurately control the volume of the droplets. Furthermore, the cooling rate of spherical Cu–20% Sn alloy particles is estimated by a Newton’s cooling model. The cooling rate of the Cu–20% Sn alloy particle decreases gradually with the particle diameter increasing. Smaller particles have higher cooling rates and when the particle diameter is less than 70 μm, the cooling rate of particles can reach more than 3.3 × 104 K/s. The secondary dendrite arm spacing has strong dependence on particle diameter which increases gradually with the increase of particle diameter. The results demonstrate that POEM is an effective route for fabrication of high-quality monosized Cu–20% Sn alloy particles.

Change mode and effects analysis (CMEA) is a powerful technique for measuring product flexibility toward future changes and diminishing the cost of redesign as well as shortening time to market. As a systematic methodology, it provides an in-depth view for the investigation of potential changes, causes, and effects in designs, products, and processes. Traditional CMEA determines the risk priorities of change modes by using change potential number, which requires the risk factors of design flexibility, occurrence, and readiness to be precisely evaluated. However, this is not always possible in real applications due to the uncertainty and subjectivity involved in the early design stages. It has been criticized much for its deficiencies in criteria weighting of the risk factors, change potential number calculation, and risk priorities determination of the change modes. This paper presents a systematic evaluation approach for determining a more rational rank of change modes by combining with the entropy weight method, rough number, and grey relational analysis. In this study, the entropy weight method is adopted to calculate the relative importance of risk factors. Rough number is presented to aggregate individual weights and preferences, and to manipulate the vagueness in the evaluation process. Then a rough number enhanced grey relational analysis is proposed to evaluate the risk ranking of change modes. Finally, a practical example is put forward to validate the performance of the proposed method. The result shows that the proposed change mode evaluation method can effectively overcome the shortcomings of traditional CMEA and strengthen the objectivity of product flexibility measurement.

The on-site hydrogen supply is a key issue for the commercialization of the fuel cells, which is one of the important ways for realizing a hydrogen-economy society. Composite NaNH2–NaBH4 is regarded as a promising high-capacity hydrogen storage material. In this paper, the composite NaNH2–NaBH4 (2/1) was synthesized via a solid-state ball milling method. To improve the hydrogen generation kinetics, a multiplex metal boride Mg–Co–B was selected as the catalyst. It was found that Na3BN2 and metal Na were byproducts in the thermal decomposed sample by X-ray diffraction analysis. Thermogravimetry and differential thermal analysis indicated that the main decomposition stages of the catalyst promoted NaNH2–NaBH4 material were split into three stages. The activation energy of the Mg–Co–B promoted NaNH2–NaBH4 (2/1) material below 300 °C was 76.4 KJ/mol, which is only 47.9% of that of the pristine NaNH2–NaBH4 (2/1), and implying much better hydrogen generation kinetics.

A CeO2/ZrO2-hydroxyapatite (HA) composite bio-ceramic coating was prepared on ZK60 magnesium (Mg) alloy by using micro-arc oxidation (MAO) and electrophoretic deposition (EPD). MAO coating was done as the basal layer was grown in alkaline electrolyte with the addition of nanoparticles (CeO2 and ZrO2) to improve the mechanical properties of coating. A HA coating as the covering layer was deposited on the surface of MAO coating for improving the biological properties of the coating. The phase compositions and morphology of coatings were monitored with X-ray diffraction (XRD) and scanning electron microscopy (SEM), respectively. Adhesion and wear resistance of coatings were evaluated using a scratch test and a pin-on-disc sliding wear test. The corrosion resistance of coatings was evaluated in a simulated body fluid (SBF) using electrochemical tests at 36.5 ± 0.5 °C. The experimental results showed that the CeO2/ZrO2-HA composite coating on Mg alloy effectively improved its mechanical properties and corrosion resistance. Combining MAO and EPD is a promising modification technology for degradable Mg alloys as biomaterials.

Se and green tea have been shown in epidemiological, observational and preclinical studies to be inversely related to the risk of developing colorectal cancer (CRC). However, there are limited studies to evaluate their regulatory effects on genes/proteins that relate to CRC oncogenesis in human subjects, such as selenoproteins, WNT signalling pathway, inflammation and methylation. This study examined the effects of supplementation of Se using Brazil nuts and green tea extract (GTE) capsules, alone and in combination, on targeted biomarkers. In total, thirty-two volunteers (>50 years of age) with plasma Se≤1·36 µmol/l were randomised to one of three treatment groups: nine to Se (approximately 48 µg/d) as six Brazil nuts, eleven to four GTE capsules (800 mg (-)-epigallocatechin-3-gallate) and twelve to a combination of Brazil nuts and GTE. Blood and rectal biopsies were obtained before and after each intervention. Plasma Se levels, rectal selenoprotein P (SePP) and β-catenin mRNA increased significantly in subjects consuming Brazil nuts alone or in combination, whereas rectal DNA methyltransferase (DNMT1) and NF-κB mRNA were reduced significantly in subjects consuming GTE alone or in combination. None of the interventions significantly affected rectal acetylated histone H3 or Ki-67 expression at the protein level or plasma C-reactive protein. Effects of the combination of Brazil nuts and GTE did not differ from what would be expected from either agent alone. In conclusion, supplementation of Brazil nuts and/or GTE regulates targeted biomarkers related to CRC oncogenesis, specifically genes associated with selenoproteins (SePP), WNT signalling (β-catenin), inflammation (NF-κB) and methylation (DNMT1). Their combination does not appear to provide additional effects compared with either agent alone.

Anthrax is still a severe public health problem and threat to human health. A cutaneous anthrax outbreak occurred in Jiangsu Province, a non-endemic anthrax region of eastern China, from July to August 2012. Epidemiological and laboratory investigation were initiated to trace the source of infection and identify the risk factors of the outbreak. On 25 July 2012, 17 persons were exposed to a sick cow, which had been imported from northeast China a few days previously. Of the 17 exposed, eight developed symptoms between 1 and 8 days and were diagnosed as cutaneous anthrax cases. Three main genes of Bacillus anthracis were detected from both human and cow meat samples, indicating that the outbreak was associated with this infected cow. A retrospective cohort study showed that contact with blood and presence of skin damage contributed to the case infection with B. anthracis. The outbreak highlights the need to enhance quarantine for imported livestock, which should have been vaccinated prior to importation, the significance of education for high-risk individuals, and training for primary healthcare workers even in anthrax-free areas.

Optics surface phase defects induced intensity modulation in high-power laser facility for inertial confinement fusion research is studied. Calculations and experiments reveal an exact mapping of the modulation patterns and the optics damage spot distributions from the surface phase defects. Origins are discussed during the processes of optics manufacturing and diagnostics, revealing potential improvements for future optics manufacturing techniques and diagnostic index, which is meaningful for fusion level laser facility construction and its operation safety.

Creative conceptual design requires significant previous design knowledge. Case-based reasoning enables learning from previous design experience and has a great potential in supporting creative conceptual design by means of seeking to retrieve, reuse, and revise most appropriate cases to generate inspired solutions. However, traditional case-based reasoning based creative conceptual design models focus on design strategies research, pay little attention to defining a consistent knowledge representation model, and neglect the research to make various types of knowledge retrieval tractable. Faced with such drawbacks, the expected design knowledge cannot be retrieved properly, especially in cases where multidisciplinary knowledge is concerned or exact query terms are absent. In order to solve these issues, this paper presents a combined approach to support creative conceptual design process. First, function–behavior–structure knowledge cell is introduced as a unified consistent design knowledge representation model. Second, a hybrid similarity measure is proposed to increase the overall possibility of obtaining useful design knowledge by considering semantic understanding ability. Third, an intelligent creative conceptual design system has been developed with a case study of a novel insulin pump design to demonstrate its usage, and two experiments are conducted to evaluate the performance of the proposed approach. The results show that the proposed approach outperforms other case-based reasoning based creative conceptual design models.

In this paper, we propose a new algebraic method to construct non-autonomous discrete integrable systems. The method starts from constructing generalizations of convergence acceleration algorithms related to discrete integrable systems. Then the non-autonomous version of the corresponding integrable systems are derived. The molecule solutions of the systems are also obtained. As an example of the application of the method, we propose a generalization of the multistep ϵ-algorithm, and then derive a non-autonomous discrete extended Lotka–Volterra equation. Since the convergence acceleration algorithm from the lattice Boussinesq equation is just a particular case of the multistep ϵ-algorithm, we have therefore arrived at a generalization of this algorithm. Finally, numerical experiments on the new algorithm are presented.

Epidemiological studies have identified increased colorectal cancer (CRC) risk with high red meat (HRM) intakes, whereas dietary fibre intake appears to be protective. In the present study, we examined whether a HRM diet increased rectal O6-methyl-2-deoxyguanosine (O6MeG) adduct levels in healthy human subjects, and whether butyrylated high-amylose maize starch (HAMSB) was protective. A group of twenty-three individuals consumed 300 g/d of cooked red meat without (HRM diet) or with 40 g/d of HAMSB (HRM+HAMSB diet) over 4-week periods separated by a 4-week washout in a randomised cross-over design. Stool and rectal biopsy samples were collected for biochemical, microbial and immunohistochemical analyses at baseline and at the end of each 4-week intervention period. The HRM diet increased rectal O6MeG adducts relative to its baseline by 21 % (P< 0·01), whereas the addition of HAMSB to the HRM diet prevented this increase. Epithelial proliferation increased with both the HRM (P< 0·001) and HRM+HAMSB (P< 0·05) diets when compared with their respective baseline levels, but was lower following the HRM+HAMSB diet compared with the HRM diet (P< 0·05). Relative to its baseline, the HRM+HAMSB diet increased the excretion of SCFA by over 20 % (P< 0·05) and increased the absolute abundances of the Clostridium coccoides group (P< 0·05), the Clostridium leptum group (P< 0·05), Lactobacillus spp. (P< 0·01), Parabacteroides distasonis (P< 0·001) and Ruminococcus bromii (P< 0·05), but lowered Ruminococcus torques (P< 0·05) and the proportions of Ruminococcus gnavus, Ruminococcus torques and Escherichia coli (P< 0·01). HRM consumption could increase the risk of CRC through increased formation of colorectal epithelial O6MeG adducts. HAMSB consumption prevented red meat-induced adduct formation, which may be associated with increased stool SCFA levels and/or changes in the microbiota composition.