Stimulated Raman scattering is a third-order nonlinear optical effect that is not only effective for wavelength converting laser output, but also for single longitudinal-mode output due to the absence of spatial hole burning. Diamond is a prominent Raman-active medium that has significant potential for linewidth narrowing and wavelength converting lasers at high power levels due to its high thermal conductivity, long Raman frequency shift and wide spectral transmission range. In this work we utilize diamond in a resonantly mode-matched external cavity to achieve cascaded Raman conversion of a 1064 nm laser. By fine-tuning the length of this external cavity, we can obtain narrow linewidth emission at 1240 and 1485 nm. When operating at maximum power, the measured linewidths were more than twofold narrower than the linewidth of the fundamental field. In addition, the noise levels of the Stokes fields are lower than that of the fundamental field throughout the entire noise frequency range, and the intrinsic linewidth of the second Stokes field, which is expressed at the hertz level (~3.6 Hz), is decreased by approximately three orders of magnitude compared to that of the pump. This work represents the first measurement and analysis of the linewidth and noise characteristics of cascaded diamond Raman lasers and, significantly, offers a new means by which high-power, narrow linewidth laser output can be produced from wavelength-converted laser systems.

The stimulated Brillouin scattering phase conjugation mirror (SBS-PCM) based on liquid media is widely used in high-power laser systems due to its robust thermal load capacity, high energy conversion efficiency and improved beam quality. Nevertheless, with an increase in the pump repetition rate, thermally-induced blooming and optical breakdown can emerge, leading to distortions in the Stokes beam. In this study, we delved into the thermal effects in liquid SBS-PCMs employing hydrodynamic analysis, establishing a relationship between beam profile distortion and the thermal convection field. We calculated the temperature and convection velocity distribution based on the pump light parameters and recorded the corresponding beam profiles. The intensities of the beam profiles were modulated in alignment with the convection directions, reaching a velocity peak of 2.85 mm/s at a pump pulse repetition rate of 250 Hz. The residual sum of squares (RSS) was employed to quantify the extent of beam profile distortion relative to a Gaussian distribution. The RSS escalated to 7.8, in contrast to 0.7 of the pump light at a pump pulse repetition rate of 500 Hz. By suppressing thermal convection using a high-viscosity medium, we effectively mitigated beam distortion. The RSS was reduced to 0.7 at a pump pulse repetition rate of 500 Hz, coinciding with a twentyfold increase in viscosity, thereby enhancing the beam quality. By integrating hydrodynamic analysis, we elucidated and mitigated distortion with targeted solutions. Our research offers an interdisciplinary perspective on studying thermal effects and contributes to the application of SBS-PCMs in high-repetition-rate laser systems by unveiling the mechanism of photothermal effects.

This work demonstrates the generation of short pulse duration and high-beam-quality laser pulses using transient stimulated Brillouin scattering at a high repetition rate. Thermal effects and optical breakdown are identified as the main factors that restrict energy reflectivity and beam quality under high repetition rates and transient situations. Through experimental analysis, the interaction length and focal point size are determined to be the key parameters in reducing the thermal effect by reducing the absorption of the laser pulse by the medium. The obtained results show that pulses with a duration of 175 ps and beam quality M2 of around 1.2 can be achieved with a maximum energy reflectivity of over 40% under an interaction length of 50 mm. Furthermore, at an interaction length of 90 mm, a pulse output with a minimum duration of 115 ps (0.5τQ) is achieved.

This study analyzes the linewidth narrowing characteristics of free-space-running Brillouin lasers and investigates the approaches to achieve linewidth compression and power enhancement simultaneously. The results show that the Stokes linewidth behavior in a free-space-running Brillouin laser cavity is determined by the phase diffusion of the pump and the technical noise of the system. Experimentally, a Stokes light output with a power of 22.5 W and a linewidth of 3.2 kHz was obtained at a coupling mirror reflectivity of 96%, which is nearly 2.5 times compressed compared with the linewidth of the pump (7.36 kHz). In addition, the theorical analysis shows that at a pump power of 60 W and a coupling mirror reflectivity of 96%, a Stokes output with a linewidth of 1.6 kHz and up to 80% optical conversion efficiency can be achieved by reducing the insertion loss of the intracavity. This study provides a promising technical route to achieve high-power ultra-narrow linewidth special wavelength laser radiations.

Stimulated Raman-scattering-based lasers provide an effective way to achieve wavelength conversion. However, thermally induced beam degradation is a notorious obstacle to power scaling and it also limits the applicable range where high output beam quality is needed. Considerable research efforts have been devoted to developing Raman materials, with diamond being a promising candidate to acquire wavelength-versatile, high-power, and high-quality output beam owing to its excellent thermal properties, high Raman gain coefficient, and wide transmission range. The diamond Raman resonator is usually designed as an external-cavity pumped structure, which can easily eliminate the negative thermal effects of intracavity laser crystals. Diamond Raman converters also provide an approach to improve the beam quality owing to the Raman cleanup effect. This review outlines the research status of diamond Raman lasers, including beam quality optimization, Raman conversion, thermal effects, and prospects for future development directions.

Laser pulses of 200 ps with extremely high intensities and high energies are sufficient to satisfy the demand of shock ignition, which is an alternative path to ignition in inertial confinement fusion (ICF). This paper reports a type of Brillouin scheme to obtain high-intensity 200-ps laser pulses, where the pulse durations are a challenge for conventional pulsed laser amplification systems. In the amplification process, excited Brillouin acoustic waves fulfill the nonlinear optical effect through which the high energy of a long pump pulse is entirely transferred to a 200-ps laser pulse. This method was introduced and achieved within the SG-III prototype system in China. Compared favorably with the intensity of $2~\text{GW}/\text{cm}^{2}$ in existing ICF laser drivers, a 6.96-$\text{GW}/\text{cm}^{2}$ pulse with a width of 170 ps was obtained in our experiment. The practical scalability of the results to larger ICF laser drivers is discussed.

Dalian, China, is a city free of rabies in recent 20 years, but the annual cost for rabies vaccination still brings an economic burden on society and individuals. We did a retrospective descriptive analysis to analyse the reason for this and try to find some ways to resolve it. A total of 10 028 post-exposure prophylaxis (PEP) cases were recorded from January 2016 to December 2017. According to the exposure grades, 32 cases were grade I; 7712 cases were grade II; 2284 cases were grade III. All the patients in the cases were injured by pet dogs without abnormal clinical signs, and 80% of them were home pet dogs. Fifty-two per cent of the pet dogs were vaccinated. All the dogs survived during the PEP vaccination period. The data showed that a considerable proportion of people who did not have exposure risk for rabies had received vaccination. The underlying reasons included social, medical and personal factors. So here we proposed to replace the current ‘five-course’ intramuscular injection with intradermal injection method in the cities free of rabies in China, this can not only achieve effective vaccination but also save resources and eliminate the fear of rabies from victims. Meanwhile we should strengthen communication on rabies knowledge and make a routine evaluation of rabies surveillance system to improve understanding of the risk for rabies from biting animals.

A 100-J-level Nd:glass laser system in nanosecond-scale pulse width has been constructed to perform as a standard source of high-fluence-laser science experiments. The laser system, operating with typical pulse durations of 3–5 ns and beam diameter 60 mm, employs a sequence of successive rod amplifiers to achieve 100-J-level energy at 1053 nm at 3 ns. The frequency conversion can provide energy of 50-J level at 351 nm. In addition to the high stability of the energy output, the most valuable of the laser system is the high spatiotemporal beam quality of the output, which contains the uniform square pulse waveform, the uniform flat-top spatial fluence distribution and the uniform flat-top wavefront.

Most of the high-energy laser systems deliver temporally super-Gaussian-shaped laser pulses. The propagation properties of this kind of pulses in a nonlinear medium are studied in this paper. There is Stokes component in the sideband spectrum of super-Gaussian-shaped pulses, and the frequency difference between the Stokes component and the center frequency is equals to the Brillouin frequency of the nonlinear medium. When the laser is reflected by optical elements in the light path, Stokes component in the reflected light can be amplified by the subsequent part of the laser pulse and excite stimulated Brillouin scattering (self-pumped SBS). The self-pumped SBS is studied theoretically and experimentally, and the experimental results agreed well with the calculated results. The simulation results show that lower-order super-Gaussian-shaped pulses are more suitable for suppressing the self-pumped SBS and of great benefit to the energy delivering of the high-power laser pulses. To the best of our knowledge, this is the first time to experimentally demonstrate the self-pumped SBS of high-power super-Gaussian-shaped laser pulses.

We obtained the output of single frequency laser pulses with an average pulse-width of 136 ps and the minimum of 123 ps based on stimulated Brillouin scattering pulse compression pumped by an 8 ns-pulse-width, 1064 nm-wavelength Q-switched Nd:YAG laser. The pulse-width stability of the output is about 4.1% while that of the pump pulses is about 1.1%, the highest energy conversion efficiency is about 85%, and the single pulse energy is above 300 mJ.

A novel approach of beam cleanup based on stimulated Brillouin scattering with a large core fiber is proposed to improve the laser beam quality. The fusion splice scheme from a single-mode fiber to a very large core fiber (105 µm) is first employed in stimulated Brillouin scattering to steadily excite the fundamental mode of the Stokes beam. As a result, the output beam achieves a measured M2 value of around 1.3 meanwhile the pump conversion efficiency is up to 90%, which is the best in the reports of stimulated Brillouin scattering cleanup to our knowledge.

Based on transferring energy from multiple pump beams into one Stokes beam using Brillouin amplification, a serial coherent laser beam combination scheme is presented, which has many advantages, such as, simple structure, low cost, ease of adjustment, higher load capability, scalable easily, etc. Furthermore, it has been demonstrated that the combination of several beams using this method is theoretically possible. But in practice, the amplification of high power Stokes beam is a key problem to solve. In this paper, the amplification of Stokes beam whose power is higher than the pump beam is first studied and proved experimentally. Coupling the two laser beams by this method is proved experimentally, and the coupling efficiency reaches more than 80%. Then the feasibility of multiple beams combination based on Brillouin amplification is analyzed and tested theoretically.