Multidisciplinary conceptual design for a hybrid-electric commuter aircraft

Abstract The electrification of the commuter aircraft is instrumental in the development of novel propulsion systems. The scope of this work aims to explore the design space of a parallel hybrid-electric configuration with an entry into service date of 2030 and beyond and determine the impact of other disciplines on conceptual design, such as components positioning, aircraft stability and structural integrity. Three levels of conceptual sizing are applied and linked with a parametric aircraft geometry tool, to generate the aircraft’s geometry and position the components. Subsequently, the structural optimisation of the wing box is performed, providing the centre of gravity of the components placed inside the wing, that minimise the induced stresses. Furthermore, the stability and trim analysis follow, with the former being highly affected by the positioning of components. Results are compared to a similar aircraft with entry into service technology of 2014 and it is indicated that in terms of block fuel reduction the total electrification benefit increases with the increase of degree of hybridisation, if aircraft mass is kept constant. On the other hand, if battery specific energy is kept constant, similar block fuel reduction is possible with lower hybridisation degrees. The potential for improvement in terms of carbon dioxide emissions and block fuel reduction ranges from 15.73% to 21.44% compared to the conventional aircraft, for levels of battery specific energy of 0.92 and 1.14 kWh/kg respectively. Finally, the component positioning evaluation indicates a maximum weight limitation of 240 kg for the addition of an aft boundary layer ingestion fan to a tube and wing aircraft configuration, without compromising the aircraft static stability.


Introduction
Moving forward to the current decade, novel propulsion architectures will emerge to comply with the emission and noise regulations posed by aviation administrations around the globe. According to European Aviation Safety Agency -EASA, 3% of total carbon emissions is generated by air transportation. In addition, it is estimated that the total number of flights in Europe will increase by 42% until 2040, compared to 2017, leading to an increment of 21% in respective carbon-dioxide emissions [1].
To overcome this increase, alternative propulsion concepts are being investigated, one of them being the hybrid-electric propulsion. Considering the current technological maturity, the commuter aircraft class is an ideal electrification candidate. That is because battery technology, neither is, nor will be capable of covering energy and power requirements for aircraft with gross take-off mass of 25 tonnes and above in the foreseeable future [2]. While methodologies for conventional aircraft sizing are well-established, as seen in the work of Henderson et al. [3], aircraft hybridisation studies are still under the microscope. Thus it is necessary to determine the status and the level of fidelity of publicly available approaches and decide the way forward.
phases, compared to the conventional ATR 72, with battery specific energy of 0.2 kWh/kg. Similar batteries SoA is assumed in the work of Juretzko et al. [22], where a Dornier Do 228 is retrofitted, that is capable of performing Take-Off and Climb with electric power only, while batteries maintain charge in cruise. The payload is reduced to maintain the maximum take-off weight, as a penalty of the addition of the electric powertrain. Compared to the conventional Do 228, the range of the retrofit is reduced by 37%, indicating that the retrofit cannot perform as the baseline, with the current battery SoA. Finally, more promising indications are presented in the work of Wall et al. [23], where a Cirrus SR20 is retrofitted, with simulation suggesting a fuel saving of 15.6%, compared to the conventional aircraft. From the aircraft sizing review, it is observed that most of the approaches focus on batteries and fuel weight estimation and hybrid-electric powertrain sizing and performance, without examining other disciplines, i.e., component positioning, aircraft stability and structural evaluation. In a commuter aircraft, space is a limiting factor in terms of positioning and energy storage space availability. Moreover, the CS-23 airworthiness certification poses a mass limit of 8,618 kg [15], that complicates aircraft electrification, as the additional weight penalty of the electric powertrain is substantial. In a conventional aircraft, fuel is stored inside the wing-box and has a minor impact on the overall stability. Furthermore, it is depleted during the mission, thus reducing the aircraft's weight and structural loads. However, in a hybrid-electric aircraft, where batteries are present, the total mass of the aircraft is greater, increasing the structural loads. In addition, the positioning of the batteries is important, as it is a considerable amount of weight, thus affecting the overall stability of the aircraft. Given the above, it is necessary to include the positioning and stability disciplines in the aircraft sizing process and address the challenges in the design. All things considered, the present work aims to explore the design space for a 19-seat hybrid-electric commuter aircraft, with an EIS date of 2030. At first, the sizing methodology is presented, expanding up to a third level of refinement. Subsequently, an automated procedure for the geometry generation of the aircraft is explained, followed by the structural optimisation of the wing-box. In addition, the positioning of the components occurs, and static stability and trim analysis calculations are showcased. All the above are included in a single framework, forming a multidisciplinary environment that is capable to connect to additional -more detailed -sizing modules for different aircraft components. Results explore the design space for the parallel hybrid-electric configuration with electric power supplied at all mission phases. Additionally, the potential for block fuel reduction of the design, compared to a conventional configuration with EIS date of 2014, is established while exploring different technological advancements. Finally, the impact of the positioning of components and structural optimisation on the Centre of Gravity -CoG and stability of a designed aircraft is discussed.

State of the art and challenges in electrical machines
The SoA of energy storage is reviewed in the work of Gkoutzamanis et al. [20]. However, energy storage is not the sole driver in hybrid-electric aircraft design. The Technology Readiness Level -TRL of electrical machines will also determine the feasibility of a hybrid-electric design. Considering the work in Ref. [24], the specific power of electrical components will determine the overall weight of the electrical powertrain. Table 1 indicates the research that is under progress globally and is publicly available through several references. Applicability in the small aircraft is again commented along with the various concerns around these components of the powertrain.
Most technologies currently under research, have lower specific power which makes them impractical for the case of the 19-passenger aircraft. Bodson et al. [25], consider a Hybrid Electric Propulsion -HEP system that transmits the power from the generator directly to electrical motors, without conversion inbetween. The validation of their work is performed at a low-power test bench, and results indicate that this configuration can be scaled-up for commercial air-transportation use successfully.
Furthermore, because CS-23 imposes significant weight limits, one of the primary goals of design is to have a powertrain as lightweight as possible. One potential solution is to match the propeller and motor to eliminate the need for gearbox, while the motor is operating at low rpm. The challenge at this point is to ensure that the speed of the motor shaft is equal to the speed of propellers. This implies that  the motor must be designed in such a way to withstand torque and thrust loadings, as well as structural and vibration loads emanating from the propeller rotation. The requirement for high current densities implies that the thermal management system is the key enabler for the development of such machines. Lastly, to attain full entitlement of new machine architectures, advanced manufacturing techniques such as to build slot-less windings, composite structures and superconducting coil assemblies need to be purchased.

Top-level aircraft requirements
In order to initiate the design process, the Top-Level Aircraft Requirements -TLAR must be defined, that are selected according to the mission type and aircraft design and can be modified if the design constraints are not met. In Table 2, the design case TLAR are presented, selected to be similar to those in the work of Romano et al. [37], as they are based on market related scenarios. The selected reference aircraft is a conventional twin-turboprop, equipped with two engines similar to PT6A-67D Pratt & Whitney [38] and an EIS date of 2014. On the other hand, the examined hybrid-electric configuration is a parallel-hybrid, twin-turboprop aircraft with a potential EIS of 2030+. Both aircraft were sized within the proposed framework using a simple mission profile, consisting of five discrete segments: 1. Taxi and Take-Off, 2. Climb, 3. Cruise, 4. Descend and Loiter, 5. Approach, Landing and Taxi-back, as shown in Fig. 1.

Aircraft sizing
To calculate the maximum take-off mass, the operating empty mass and the required amount of fuel and batteries, the methodology that is followed is based on that proposed by Raymer [5], modified accordingly to fit the hybrid-electric architecture. The aforementioned masses are described as fractions of the maximum take-off mass in Equation (1), which is solved iteratively to calculate the maximum take-off weight. The operational empty mass fraction is estimated using historical data for the first two levels of sizing, as described in Equation (2). Parameters A, C, K VS , α 0 , α 1 and c 1 − c 5 are derived from tabulated data for twin-turboprop aircraft [5]. Since the regression curves that these equations describe are derived for conventional aircraft, the additional weight of the electric powertrain is estimated and included in the empty weight calculation in a forward step.
Fuel and battery mass fractions are calculated for each discrete mission segment, considering the Degree of Hybridisation -DoH in terms of power, as it is described in Equation (3). According to this definition, P el is the continuous electrical power of the electric motor and P gt is the power provided by the gas turbine. The Degree of Hybridisation can receive any value between 0 and 1, with 0 representing the conventional aircraft and 1 the pure electric. For the parallel hybrid configuration, the total thrust can be divided into thrust produced by the electric motor and gas turbine respectively. Climb, cruise and loiter can be considered steady level flight segments; climb is a superposition of level flight and climb gradient. This consideration poses a direct relationship between Lift and Weight and Thrust and Drag, derived from the free-body diagram, that allows the substitution of T/W ratio with the inverse L/D ratio. Hence, H p can be multiplied with Drag to account for the electrically produced thrust. Therefore, the required battery mass fractions are calculated using Equations (4)- (6). The fuel mass fraction is calculated using Breguet's equation for cruise and loiter as shown in Equations (7)-(8), whereas fixed ratios are selected from tabulated data for all other segments, as shown in Table 3, and are used in Equation (9). Additionally, 6% trapped fuel after landing is also considered in Equation (9).
The proposed aircraft sizing method is an in-house tool developed in Python programming language and is connected to OpenVSP [39] to generate the aircraft 3D sketch with a geometry generator, that has been developed for the purposes of this work. The resulting 3D sketch provides the required information (i.e., exposed, and wetted areas and individual component volumes) to proceed to the final level of sizing. In addition, this information is imported to the Aerodynamics module of the proposed framework, that calculates the parasite drag coefficient, using the parasite drag component build-up method. Finally, the centre of gravity vector for each component is extracted and will be used in the stability and control modules.
In the second sizing level, aircraft power loading is calculated using Equation (10) and L/D is calculated from the wing loading at each segment, using Equation (11). The aircraft wing loading is calculated for each mission phase according to the Top-Level Aircraft Requirements and the mission profile definition. Then, the actual wing loading is calculated for each phase, considering the change in aircraft mass throughout the mission. The more refined estimation of maximum take-off weight allows for a more accurate estimation of the dimensions for the fuselage, wing and empennage, that will lead in the final estimation of the aircraft empty mass. A component build-up method is deployed that examined each aircraft part an performs the mass estimation. Additionally, the weight of electrical components is included in this step, using the mass estimation method proposed by Teichel et al. [40]. It includes the mass estimation of electrical motors/generators, inverters, cooling components, gearbox, rectifiers, and cables. For electrical motors with continuous power less than 500 kW, a new mass estimation is introduced that is derived from data provided by EMRAX [26], considering continuous power ranging from 188 to 348 kW. The equations used to estimate the components mass (i.e., fuselage, wing, empennage, etc.) can be found in Refs. [41], [42] and in chapter 15 of Ref. [5]. For the sake of brevity, only the build-up of the operating empty mass is presented in Equation (12). The weight of avionics, furniture, consoles etc., is symbolised as W else and is considered to be 17% of the maximum take-off mass, as proposed in Ref. [5].
The weight component build-up method qualifies as the third -and final -level of sizing. In this way, the impact of aircraft dimensions on the maximum take-off mass is captured. At each iteration, a new aircraft is sized, new dimensions are extracted, and an updated operating empty mass is calculated. Thus, the final maximum take-off mass is calculated, considering the actual dimensions of the design. Subsequently, the proposed design process continues with the other framework modules, namely Aerodynamics, Structural evaluation, Positioning, Centre of Mass and Stability, as shown in Fig. 2. In the Aerodynamics module, apart from the drag calculation, the aircraft drag polar is extracted as well. Additionally, in the structure model, the structural optimisation of the wing-box using a mixedfidelity approach is performed and finally, the impact of component positioning on the aircraft centre of mass and static stability is evaluated. The output of all modules is thoroughly discussed in the results section.

Assumptions
The most important assumptions in the presented design process are listed below: • Aircraft is fully loaded during the initial phases of the mission • The operating empty mass is estimated from historical data in the beginning and the additional mass of the electric powertrain is considered in the third level of sizing • "Rubber engines" are considered for the design evaluation, thus only the total power requirement is calculated • Specific fuel consumption for cruise and loiter is selected from similar aircraft using PT6A-67D engines [43] • Hot day ground conditions are considered • The propeller efficiency for the discrete mission phases is estimated according to the work of Giannakakis et al. [44] • The total electrical powertrain efficiency, from batteries to shaft ranges from 90% to 94% considering electrical machine efficiencies (92%-96%) from Table 1, inverter efficiency (99%) [45] and battery pack efficiency (99.1%) [46] • Climb and approach speed are selected according to CS-23 [15]/FAR-23 [16] airworthiness certification • A parallel hybrid-electric propulsion architecture is examined

Model verification
The validity of the model has been verified using data from four different conventional aircraft as shown in Table 4. Data from aircraft manufacturers have been obtained and compared to the prediction of the proposed aircraft sizing tool. It is observed that the empty and maximum take-off weight prediction is within acceptable limits (< 5%) in all cases. When considering the aircraft dimensions (i.e., the fuselage length, span, and reference area), the prediction error increases. That is because, these parameters are subject to additional design selections that were assumed or calculated separately in the validation process. For example, both wing span and reference area depend on the wing loading selection. In this work, the wing loading is calculated for each mission segment, and the minimum value is selected for safety reasons. Additionally, the fuselage length is expected to change further down in the design process as part of the component positioning optimisation. Considering the above, the dimension deviation of the prediction compared to the manufacturer's data is considered within acceptable limits for a conceptual design tool.

Design space exploration
Using the framework described in the previous sections, a design space exploration is performed, using the third level of sizing, to determine the effect of the hybridisation degree and specific energy of the batteries on maximum take-off mass. Figures 3 and 4 show the variation of aircraft maximum take-off mass with respect to the specific energy of batteries and degree of hybridisation, for two different service ceilings, i.e., 10,000 and 25,000 ft. The mission range examined is 400 nm, plus 100 nm reserves and 30 minutes of loiter time, whereas the cruise speed is 195 kn. Pairs of values that result in a take-off mass ≥ 8,618 kg are filtered out of the graph, keeping in mind the CS-23/FAR-23 certification, which explains the constrained surfaces for the combination of low specific energy and high degree of hybridisation. It is evident that specific energy is the main driver of this design space exploration, especially in the lower values area, where the slope is greater. On the other hand, the effect of hybridisation degree on maximum take-off mass can be described as linear, but this can be also explained by the formulae presented in the previous section. Comparing the different service ceilings, it can be observed that the higher the altitude, the more the maximum take-off mass becomes. When flying at an altitude over 10,000 ft, oxygen must be carried to prevent hypoxia due to air being less dense at higher altitudes. Furthermore, a cabin pressurisation system must be added to the air conditioning system of the aircraft, that results in a weight penalty. This penalty is included in the operating empty mass in the present framework, which explains the increase in the maximum take-off mass, thus reducing the acceptable design space. In addition, increasing the top of climb, translates to additional fuel, that further increases the maximum take-off mass. Considering the operational aspects of a commuter aircraft and the mass limitation posed by the certification, a service ceiling of 10,000 ft is selected to reach an earlier EIS. Said that, it can be observed that the design space offers some realistic pairs when considering EIS of 2030+. It should be noted that with a compromise in the maximum range, the need for more energydense batteries will reduce, however this requires an area-based market analysis, which is out of the scope of this publication.

Benefits of electrification
A comparison analysis follows between the reference aircraft and three different parallel hybrid-electric design cases with constant hybridisation degree throughout the mission. Four different H p are selected, i.e., 30, 35, 40 and 50% per case, bringing up the total of compared cases to 12. Those cases are then examined for a selection of cruise ranges from 200 to 600 nm including additional 100 nm reserves, to determine the electrification benefit in terms of block fuel reduction, compared to the conventional aircraft, as shown in Table 5. The block fuel benefit for each hybrid-electric aircraft is calculated according to Equation (13) and is compared to the conventional aircraft, for each design range. For a fair comparison, all cases have the same maximum take-off mass of 8,600 kg. Since the maximum mass is fixed and the mission is pre-defined, batteries specific energy can change, to cover the specified mission. The required specific energy for each design case is summarised in Table 6.
All cases are sized within the proposed framework and aircraft characteristics are listed below: Conventional EIS 2014 is the reference aircraft. The engines considered are similar to PT6A-67D from Pratt & Whitney, conventional materials are used for manufacturing and the propulsion system has two propellers with 80% efficiency at cruise. This aircraft is equipped with technology with EIS of 2014.
Hybrid EIS 2014 is the first examined case. It has the same engines as the Conventional, plus the electrical powertrain. Again, conventional materials are assumed, and the propellers have an efficiency of 80% at cruise. The overall efficiency of the electric system -from batteries to shaft -is considered 90%.
Hybrid EIS 2030+ C is a parallel hybrid with conservative estimation of the technology available for and aircraft with EIS of 2030+. Two hypothetical turboprop engines are used, assuming 10% less Hybrid EIS 2030+ R is the most advanced variant of all. The EIS target is again 2030+, but some of the assumptions lean to the optimistic side. Two turboprop engines, with an SFC reduction of 20% compared to the Hybrid EIS 2014 are considered; a non-far-fetched assumption, according to the latest release of GE Aviation [50] about their new engine. The operating empty mass is reduced by 10%, considering the use of advanced materials and manufacturing in various aircraft components. The overall electrical efficiency is increased by 3%, compared to Hybrid EIS 2014 case, and the propeller efficiency at cruise is 83%.
Results for all cases with 35% degree of hybridisation are grouped in Fig. 5. It is observed that the benefit of electrification increases with the mission range, as cruise the longest mission phase. Furthermore, the radical improvement in technology, provides an even greater block fuel reduction, compared to the conventional case, as expected. However, since maximum take-off mass and operating empty mass are fixed, the battery specific energy varies, as shown in Table 6. As a result, less energy dense batteries are required if the efficiency of other components is also improved. Since battery specific energy ≥ 1,000 Wh/kg is still at experimental level [20], the whole powertrain system has to be improved, in order to have realistic expectations from aircraft electrification, with reference to 2014's technology.

Figure 5. Block fuel comparison of three different parallel hybrid-electic designs to a conventional aircraft (Cruise Speed 195 KTAS).
In terms of emissions, CO 2 emissions are directly related to fuel consumption. For aviation fuel, 3.16 kg of CO 2 are emitted per kg of fuel burnt [1]. In the work of Nasoulis et al. [51] the environmental impact of both conventional and hybrid-electric aircraft with different propulsion configurations (i.e., turbofan and turboprop variants) is examined, considering a life cycle analysis for aircraft conceptual design. Additionally, both EU electricity mix and power from renewable sources are considered in the environmental impact single score assessment. It is observed that for a parallel-hybrid turboprop configuration with a hybridisation degree of 0.4 the impact of electricity production on the single score is 17.82% for the EU electricity mix, whereas the impact is 0.87% when renewables are used. Therefore, in the case of ground-based charging using renewable power sources the total operational CO 2 footprint of the hybrid-electric aircraft is reduced almost by the same amount as the block fuel. Considering charging only from renewable sources may be optimistic now, however it is an opportunity to unlock the full potential of electrification and replace fossil fuel-based energy with sustainable energy sources, both in aircraft and airport operations. For example, Schiphol airport in the Netherlands is committed to become a CO 2 neutral airport by 2030 [52]. This means that the aviation industry is currently investing in the upgrade of airport infrastructure towards a more sustainable mobility future.

Conceptual design summary
Sizing results for the examined aircraft are presented in Table 7. Considering the trends and remarks shown in the previous sections, three parallel hybrid-electric aircraft are sized, following the assumptions of the radical case presented in the previous section. Also, the conventional aircraft with EIS of 2014 is sized to serve as reference. Two different degrees of hybridisation and two different battery specific energies are tested. All cases comply with the CS-23/FAR-23 airworthiness certification, as the maximum take-off mass is less than 8,618 kg. Hybrid 1 assumes a radical improvement in specific energy (1,143 Wh/kg) which leads to a maximum take-off mass of 8,075 kg and 21.01% CO 2 and block fuel reduction. Since the specific energy selected in Hybrid 1 is very optimistic, Hybrid 2 is sized, with the same inputs apart from the battery specific energy. In Hybrid 2 the specific energy is considered 920 Wh/kg -still an optimistic value -than ensures that the maximum take-off mass will be within the certification limits. By decreasing the specific energy, the maximum take-off mass increases, leading to a slimmer block fuel reduction benefit of 15.73%. Finally, Hybrid 3 is sized, with the same specific energy as Hybrid 1, but with a higher H p . As a result, the total amount of batteries increases, thus the operating empty mass and maximum take-off mass also increase. Therefore, the benefit of block fuel reduction increases to 21.44%. In conclusion, even though Hybrid 3 has a H p of 45%, it provides only 0.43% more block fuel reduction than Hybrid 1, with a H p of 35%, thus proving the impact of additional battery weight on the aircraft sizing "snowball effect".

Structural optimisation
The produced aircraft geometry from this framework is used to create the FEA structural model of the wing-box. An in-house script has been developed that enables parametric structural modeling of the aircraft, focusing on the wing. The initial structural model is imported in ANSA [53], to discretise the geometry into FE elements. The structural model of the wing-box consists of the main structural  elements, i.e., spars and ribs, along with the exterior skin of the wing, as shown in Fig. 6. A point mass mounted on the frame is included to represent the engine assembly weight and volume elements are placed inside the wing-box to account for the available fuel and batteries storage. The scope of the structural optimisation is to find the optimum spars position that minimises the root stresses and the maximum deflection of the structure, while the required battery and fuel storage volume inside the wing-box is a constraint. For this reason, morphing boxes were created, that enable the FE entities to alter their shape and position in the model, while ensuring that the elements stay attached to each other. The spars slide in the chord direction, altering the width of the wing-box, as shown in Fig. 7. The internal spar movement affects the total available volume for fuel and batteries storage, as well as the location of the wing centre of mass in the longitudinal direction. The exterior skin of the wing is used as a constraint and the spars slide on the wing skin, without affecting the external aerodynamic shape of the wing. The spar sliding on the wing skin alters their second moment of inertia, therefore the structure is strengthened or weakened, according to the spar movement. Additionally, the impact of the longitudinal movement of the centre of mass of the components stored inside the wing, as well as the wing itself, that occurs from the structural optimisation is examined in the positioning and stability module of the framework.
The structural model consists of 45,540 CQUAD4 and 656 CTRIA3 elements that represent the spars, ribs, and the exterior skin of the wing, whereas 12,000 CHEXA6 elements were used to model the available energy storage inside the wing-box. Load boundary conditions include gravity and lift distributed as force on the exterior skin of the wing, using Schrenk's approximation on lift distribution [54], while the spars are supported on the wing root. The case of 2.5 · g maneouver is tested at maximum take-off mass, as it results in the maximum bending moments on the wing structure. The solution is a static structural SOL 101. The optimisation case is set up in modeFRONTIER [55], using the Simplex algorithm. The objective function is to minimise the induced stresses at the root, with constraints in maximum wing deformation and minimum volume for fuel and battery storage.
The design space explored is shown in Fig. 8, including both feasible and unfeasible solutions. The x axis shows the maximum wing deformation, while the y axis represents the maximum stress on the root. Pairs of values for the spars position that satisfy all the constraints, i.e., the maximum wing deflection and available volume for batteries and fuel storage, are marked as feasible. Many spars positioning pairs lead to minimum root stresses and simultaneously lower wing deformations, however the volume criteria are not met. This means that a compromise between lower wing deflection and storage availability must be made. A more detailed design space exploration, with additional design variables, can be found in the work of Nasoulis et al. [56], for the investigation of the impact of the non-structural weight added on the stress, deformation and spanwise thickness distribution of the structure. Furthermore, correlations between wing deflection and storage volume, as well as component thickness and stresses are presented in the aforementioned work. In conclusion, the optimisation process results in an overall stress reduction of 41% for the root stresses and a 24.5% reduction of the total wing deformation, compared to the initial wing-box design, as derived from the model.
Stress results are shown in contour plot in Fig. 9. It is evident that there is a higher stress concentration at the root, as the wing is cantilever. Gray-scaled areas have minimum stresses; thus, topology optimisation can be applied for material reduction. In addition, although the root stresses are within acceptable limits [57], truss-bracing the wing will result in further stress relief, leading to significant weight reduction. However, both proposals belong to a later -more detailed -step of the aircraft design, thus they are beyond the scope of this work.

Positioning aspects and stability
Combining the component-wise weight estimation, the 3D sketch of the aircraft, and the position of the fuel and batteries storage compartments, the aircraft's total centre of mass can be calculated. The origin of the coordinate system used in this work is the fuselage's nose and each component is placed with reference to that point. A rule of thumb for the initial positioning of the wing is that the mean aerodynamic chord of the wing must be collinear with the aircraft centre of mass to ensure stability. In the stability evaluation process, the position of the wing can alter to fulfil the stability criteria. In addition, the empennage should be placed appropriately to generate the required moment to counteract the pitching motion of the aircraft. Finally, the positioning of the rest of the components is done with respect to the available volume for storage and maintenance practicality. In Table 8, the x location of each component is presented, along with the calculated mass. In an aircraft this size, the positioning of the batteries is of utmost importance, as the available storage space is generally restricted. It is evident that stability issues will raise if all the weight of batteries is concentrated in one specific compartment of the aircraft. One solution is to integrate the batteries inside the floor of the aircraft. This solution will result in a uniform weight distribution, that will not have a huge impact on stability. However extra insulation measures must be taken to protect the passengers in that case and practicality issues in maintenance will raise. An interesting approach can be found on the work of Riboldi et al. [58], where the batteries are part of the structural members of the aircraft. These structural batteries resemble the structure of carbon fiber composites, where the matrix has dielectric characteristics and can store electric energy, while maintaining the structural integrity. On the other hand, batteries can be split into different packages and placed in the fuselage in a way that they cancel each other out, to preserve stability. In that case the additional cable weight should be considered and, accessibility issues must be addressed, for repairing purposes. In the examined case, three batteries containers are selected that are placed in different segments, as shown in Table 8. The weight of the DC cables for the connection of these packs, is equally distributed in the three packs for the calculation of the centre of mass.
To retrieve the positioning values of the designed components, OpenVSP is used. By using crosssections and assuming a uniform material distribution along the shape of each component, the centre of mass is extracted. The centre of mass of the batteries and fuel inside the wing-box is an output of the structural optimisation simulation. All things considered; the total aircraft centre of mass is evaluated. In Table 9 some basic aircraft loading conditions are examined, in order to find the most forward and most aft position of the centre of mass. Results presented in Tables 8, 9 are unique, since no similar references could be found in literature.
To calculate the static margin of the aircraft, the neutral point is required. In Equation (14), substituting C mcg = 0 and solving forX CoG gives the neutral point. All aerodynamic coefficients appearing in Equation (14) are calculated in the Aerodynamics module. Static margin is calculated form Equation (15), using the most aft position of the centre of mass, as presented in Table 9, divided by the mean aerodynamic chord. The examined aircraft has a static margin of 24%, meaning a very stable aircraft. This leaves room for altering the positioning of the components, e.g., change the position of the electrical powertrain components to minimise cable length; an objective that will reduce the total electrical powertrain weight significantly. Furthermore, a 24% static margin indicates that an aft BLI engine can be integrated in this parallel-hybrid configuration, and reduce the required propulsion power up to 9%, considering the aero-propulsive benefit that it offers [59]. Adding an aft propulsion system with a total  mass of ≤240 kg will reduce static margin to 7%, which is still acceptable for a commuter aircraft.
S.M. =X np −X CoG (15) Subsequently, the trim analysis of the aircraft is conducted, using the most forward position of the centre of mass. The scope of this analysis is to ensure that the empennage can produce enough moment to counteract the pitching motion of the aircraft at all mission phases. Three key parameters affect the produced empennage moment, i.e., the horizontal tail reference area and incidence, and the longitudinal distance from the wing. These parameters can alter to ensure a well-trimmed design, with the most common parameter being the horizontal tail incidence angle. Using Equation (14) for various angles of attack the aim is to find the elevator deflection that results in zero moment coefficient. In Fig. 10, the trim plot for cruise is presented, with wing flap deflection set to zero. Results show, that for the lift coefficient required for cruise condition, the aircraft is trimmed for a zero-degree elevator deflection angle, with the horizontal tail incidence being -3 degrees. An overview of the examined disciplines in the proposed framework is presented in Fig. 11, combining aircraft sizing, geometry generation, structural  modeling and optimization of the wing box, and positioning aspects of the components that affect the static stability of the design.

Conclusions
An automated computational framework for the conceptual design of a hybrid-electric aircraft was presented and applied to the commuter class. Multiple disciplines were examined, including the aircraft sizing, aerodynamic behaviour, structural integrity, positioning, and static stability. The proposed framework was validated using data from four different conventional aircraft and weight prediction was within acceptable limits (<5%). A design space exploration was performed to determine the impact of battery specific energy and degree of hybridisation on maximum take-off mass. It was observed that energydense batteries (>800 Wh/kg) are required to have more than 15% of the total propulsion power derived from an electric source, while complying with the CS-23 airworthiness certification in terms of maximum take-off weight, for the parallel hybrid configuration. Three parallel hybrid-electric designs with different technological advancements per case, were compared to a reference aircraft with 2014 technology, to determine the benefit of electrification in terms of block fuel and CO 2 emissions reduction. Fuel economy increased with range, as the degree of hybridisation was set constant for the mission.
Additionally, the energy density requirement for batteries was reduced when more efficient powertrain components were assumed. Subsequently, a conceptual design summary was presented, comparing three hybrid-electric aircraft variants to a conventional aircraft with 2014 technology. Results indicated that the block fuel reduction of Hybrid 1 was marginally lower than that of Hybrid 3, despite the latter having 10% more degree of hybridisation, thus proving the impact of the additional battery weight on the overall aircraft sizing. The structural optimisation of the wing-box suggested that trade-offs exist between wing deflection and storage availability for fuel and batteries inside the structure. The design was optimised to reduce the root stresses by altering the location of the spars, resulting in 41% stress reduction and 24.5% deflection reduction compared to the initial design. Finally, the impact of the components positioning on the static stability of the aircraft was examined, indicating that novel aircraft propulsion architectures, such as Boundary Layer Ingestion, can be applied to the commuter class. The addition of an aft BLI fan with a mass of 240 kg or less, led to a statically stable aircraft, with a 7% static margin.