Drilling stone vessels in third-millennium BC Iran: new evidence from Hajjiabad-Varamin, Jiroft (Kerman Province)

Abstract Stone vessels were widely used across the Middle East and East Mediterranean during the Bronze Age. Production sites in Egypt have been extensively studied but the evidence for other regional manufacturing centres, including the eastern Iranian Plateau, is less well understood. The authors report on an extensive craft activity area found at Hajjiabad-Varamin, Kerman Province, with evidence for the large-scale production of vessels made of translucent travertine/calcite. Drill heads or bits used to manufacture stone vessels are examined in broader temporal and geographical context. These finds raise questions about production techniques and demonstrate how apparently non-descript stones can add to our understanding of the Middle East in the third millennium BC.


Introduction
Stone vessels produced from a variety of lithologies were widely used across the ancient Middle East. In this article, we present evidence from a craft-production site at Hajjiabad-Varamin in south-eastern Iran and focus, in particular, on a collection of stone drill heads, or bits, used for the manufacture of travertine/calcite vessels ( Figure 1) (Eskandari et al. 2021). We establish the regional geological context and then use a comparative approach to consider the manufacturing techniques used and possible networks of technological knowledge across the wider Middle East. Through better documentation of stone-vessel manufacturing and the technologies used, we aim to deepen understanding of Bronze Age Drilling stone vessels in third-millennium BC Iran: new evidence from Hajjiabad-Varamin © The Author(s), 2022. Published by Cambridge University Press on behalf of Antiquity Publications Ltd stone working in Southwest Asia. We also consider the question of whether there was a specific south-eastern Iranian technological style that distinguished it from contemporaneous stone-working traditions, such as that located in Egypt.
When archaeologists of the ancient Middle East speak of 'alabaster' vessels (e.g. Casanova 1991), the term applies to the wide spectrum of semi-precious stones used for the production of these containers, and is considered "a hybrid name not recognised by geologists" (Moorey 1999: 59; also see Ciarla 1981: 46). In Iran, the raw materials used for the manufacture of these vessels were banded, fibrous-crystalline calcium carbonate rocks found within travertine deposits (Samari 2016). Composed of the carbonate minerals of calcite and aragonite, these rocks-approximately 3-4 on the Mohs scale-are relatively easy to work. Typically subtranslucent, they have a lustre ranging from dull to pearly and sub-vitreous. Bands of contrasting colours vary from white to greenish, brown, reddish, pink, yellow and, more rarely, blue. Research at third-millennium BC craft-production sites in eastern Iran (e.g. Shahdad, Shahr-i Sokhta and the Konar Sandal South complex) reveals that stonecutters produced vessels, beads and other objects using carbonate rocks with white/translucent bands of calcite alternating with bands of deep red aragonite (e.g. Kavosh et al. 2019;Eskandari et al. 2021). This evidence complements the documented long-term exploitation of travertine deposits in Iran as a source of various ornamental stones through to the present day (Hora 1996). In the still-active ornamental stone industries of Afghanistan, Iran and Pakistan (e.g. Shafai et al. 2020: 70-75), such travertine deposits are erroneously considered to be varieties of marble. Other designations include 'green onyx' or 'Balochistan onyx'; however, these commercial labels should be reserved for banded varieties of silica/chalcedony, whose mineralogy is distinct from carbonate rocks. In this article, we focus exclusively on vessels produced using translucent carbonate rock varieties.
Carbonate rock formation in south-eastern Iran and neighbouring regions Capezzuoli et al. (2014) explain the geological processes that lead to the formation of deposits of banded calcite/travertine thus: Terrestrial carbonates comprise a wide spectrum of lithologies (speleothems, calcrete, lacustrine limestone, travertines and tufas) which are mainly precipitated under subaerial conditions from calcium bicarbonate-rich waters in a large variety of depositional and diagenetic settings. (Capezzuoli et al. 2014: 1) In areas that are tectonically active, however, they suggest that "localised travertine deposits are also developed from deeply circulating hydrothermal waters" (Capezzuoli et al. 2014: 1). In Iran, the proximity of prehistoric sites to mineral springs (Heydari-Guran et al. 2009), where the precipitation of calcium carbonate forms deposits of travertine, suggests that human groups have long been attracted to this visually appealing type of stone. According to a conference presentation by Samari (2016), a major part of Iranian travertine reserves is located along the Iranian volcanic belt, or magmatic arc, known as Urumieh-Dokhtar ( Figure 1). This belt, on average 100km wide, runs parallel with the Zagros Mountain range, from north-west to south-east, extending 1700km from the Sahand and Sabalan volcanoes in Azerbaijan to the Bazman and Taftan volcanoes in Balochistan. Samari (2016: slide 2) calls this belt the "Iranian overall onyx and travertine hot spring strip".
Along the course of the Urumieh-Dokhtar belt, Tarrah et al. (2014) report major deposits of white-banded calcite near the village of Tazerj in Hormuzgan Province, at the southern end of the Halil Rud Valley, where the stone vessel manufacturing sites presented in this article are located.
Travertine is ubiquitous in this geological context and easily accessible from the Halil Rud Valley; the massive outcrops of white carbonates are still being quarried today, 10-15km west of Jiroft. Further east, in the Chagai Hills in western Balochistan, Pakistan, and the Sukalok-Arbu belt to the north and west of the Chagai in Afghanistan, aragonite (travertine) deposits have long been a source of 'onyx marble' as an ornamental stone (Stoeser 2011). Ciarla (1981: 47-48) mentions travertine deposits along the banks of the Helmand River, on the eastern side of the Kuh-i Birjand ridge (between the Lut Desert and the Sistan endoreic basin near the Afghan border) and on gravel fans of the Kuh-i Malik Siah (along the southern Sistan piedmont on the borders of Afghanistan, Iran and Pakistan). This wealth of carbonate rocks available across south-eastern Iran makes it a likely source of these raw materials for the large-scale production of stone vessels to supply the wider ancient Middle East, including Mesopotamia.

Hajjiabad-Varamin
The site of Hajjiabad-Varamin is located near the town of Jiroft in Kerman Province. Investigations of the site have identified a large settlement on a mound, with occupation extending from the late fifth to the late third millennium BC, forming part of a dense network of contemporaneous sites, including the urban centre at Konar Sandal South 5km to the north-east (Pfälzner & Soleimani 2017;Eskandari et al. 2021). The site includes a number of cemetery areas, and, to the immediate east of the main mound, an area characterised by large quantities of broken stone vessels, indicating industrial-scale craft production ( Figure 2). The production area covers approximately 0.5ha (50 × 100m) and represents the largest known industrial site of this date on the Iranian Plateau. The pottery recovered from the surface of this area is highly fragmented and ranges in date from the early to mid third millennium BC. The stone vessel fragments include carinated shapes (Figure 3a-e) and larger, sub-cylindrical forms , as well as thousands of less distinctive fragments. These vessels were presumably broken during production, although a small number have polished bases that may indicate modification and reuse.
A full analysis of the organisation of stone-vessel production at Hajjiabad-Varamin will require quantitative surface collection of the thousands of fragments visible on the site's surface, combined with stratigraphic excavation-work not yet undertaken. It is clear, however, that the scale of production at the site was intended for export, most likely destined for the Mesopotamian market (Moorey 1999: 45-46). We focus on the recovery from the production area of 12 drill heads of different forms and various lithologies, nine of which are published here. These are discussed alongside the evidence of travertine vessels from the same location, broken during the manufacturing process while being hollowed out. All of these Drilling stone vessels in third-millennium BC Iran: new evidence from Hajjiabad-Varamin objects are now stored at the Iranian Centre for Archaeological Research at Jiroft (Kerman Province).

Calcite stone vessel production: Hajjiabad-Varamin in context
Stone vessels and possible production are attested at a number of sites in Bronze Age Iran. The large Bronze Age centre of Shahr-i Sokhta, in Sistan and Balochistan Province, has produced abundant evidence of production waste and unfinished vessels. Although no discrete workshop areas have been found at the site, Ciarla (1981) argues that it was a production centre. Based on this evidence, Ciarla (1981Ciarla ( , 1985 reconstructs a four-step manufacturing process, supported by ethnoarchaeological observation of contemporary Egyptian workshops (Hester & Heizer 1981). First, the stonecutters shaped a preform from a rough chunk or pebble by hammering and increasingly fine chiselling. Second, the interior was hollowed out using bulbous, jasper drill heads of different diameters and abrasiveness (Ciarla & Bökönyi 1985: 420). Third, the vessel walls were thinned by fine shaping with hard chisels and rubbers made of fine-grained stone. In the fourth and final step, the vessels were finished by intensive polishing, and, in some cases, covered with molten wax.
Comparison of some of the Hajjiabad-Varamin stone vessel fragments to material from other sites in the region provides insights into dating and production techniques. Ciarla (1981Ciarla ( : figs 3-5, 1985: fig. 1) presents a formal classification of approximately 1300 calcite  vessel fragments from Shahr-i Sokhta. Notably, this classification does not include the low, carinated forms that are so frequent in the Hajjiabad-Varamin collection. Recent research on the sequence of the Early Bronze Age Sistan region dates the abandonment of Shahr-i Sokhta to c. 2400/2350 cal BC (Kavosh et al. 2019). The carinated vessel type, therefore, can probably be ascribed to Akkadian or post-Akkadian times (c. 2300-2100 BC). The same carinated stone vessel form features among the cache of 110 objects of gold, silver, copper, bronze and lapis lazuli from the so-called Vase à la Cachette, an important hoard of valuable objects discovered at Susa and dated to c. 2300 BC (Benoit 2003). Akkadian inscriptions appear on stone vases of various forms (Potts 1989), while a carinated bowl made of Waagenophyllum coral limestone bears an inscription of Ur-Bawu, one of the rulers of Lagash in Mesopotamia (Marchesi 2016 : fig. 2). The abundance of carinated vessels at Hajjiabad-Varamin therefore suggests that the workshops were probably active during or after the twenty-fourth/ twenty-third century BC. By this date, the regional centre of Konar Sandal South, 5km from Hajjiabad-Varamin, had been abandoned (with a final radiocarbon date of no later than 2400 cal BC; Madjidzadeh & Pittman 2008: 76), so the production may have been controlled by another, currently unidentified centre.
Comparison of the Hajjiabad-Varamin material with the Shahr-i Sokhta assemblage also allows us to recognise evidence of the four manufacturing steps attested at the Sistan workshops. As at Shahr-i Sokhta (Ciarla 1981: 56 & fig. 9), vessel fragments from Hajjiabad-Varamin indicate that a frequent manufacturing mishap was the displacement of the drilling axis from that of the preform (Figure 3j-k). A disc in a yellowish-red, fibrous quartzite with a central indentation (Figure 3l) is unattested elsewhere in the wider region, although it finds a parallel in an object published by Pfälzner & Soleimani (2017: fig. 27, top right) from the same area as Hajjiabad-Varamin. This object could be a tool rather than an unfinished vessel-possibly a drill capstone or socket (Ilan 2016: 4) used to exert pressure on some type of drill. Another convincing parallel for this piece is known from Egypt (Willems et al. 2009: fig. 4C).
Other evidence for stone-vessel production includes a few banded lumps with multiple, incomplete drillings made from different directions: these could be training or test pieces ( Figure 3m). The interior of some bases preserve unusual bulbs ( Figure 3n) and evidence for coarse rotatory marks (Figure 3o). Finally, thick, biconical stone discs with traces of pecking are common finds in the craft-activity area and more widely across Hajjiabad-Varamin. Their function is unknown; some may have been used as flywheels for drills (see Ilan 2016: fig. 5).

Drilling stone vessels: current state of knowledge
While the pre-forming of stone vessels was a painstaking if straightforward step, as noted above, the hollowing out of the vessels' interiors was the most complex and risky part of the manufacturing process (Figure 3j-k). This hollowing-out was performed with a drill, although there is debate about the process and tools used. So-called 'twist-reverse-twist drills' (hereafter TRTD) are frequently depicted in funerary art from Old Kingdom (thirdmillennium BC) Egypt (Firth & Quibell 1935-1936Lucas 1948: 53, 84-87 & 484-87;Stocks 2003: 139-55). Hartenberg and Schmidt (1969) suggest that the TRTD was a type of crank drill with no permanent, vertical axis, used for hollowing out vessels at variable angles. Experimental studies by Stocks (2003: 148; see also Stocks 1986Stocks , 1993, however, have rejected the identification of the tools depicted in Old Kingdom art as TRTD types.
A short summary of the chaîne opératoire for Egyptian stone-vessel production, with a focus on hollowing of the vessels using copper tubular bits, appears in Nicholson & Shaw (2009: 64-65). In Egypt, copper tubular bits were used for drilling hard stone from the mid fourth millennium BC (Stocks 2003: 12). In the East Mediterranean, systematic use of tubular or core drills for stone-vessel production is well attested at the Minoan and Mycenaean centres of the second millennium BC (see Morero 2013Morero , 2014Morero , 2015. In the Indus Valley, where fine copper drills were used in bead production from the late fourth millennium BC, tubular drills are not known before the Mature Harappan phase (2600-1900 BC) (Kenoyer 2005 : fig. 6). Boccutti et al. (2015) searched for evidence for the use of copper tubular drills in the production of travertine vessels at Shahr-i Sokhta, but the results were inconclusive. It seems, therefore, that copper tubular bits were not a feature of stone-vessel production in the Iranian context. Stocks (2003: 128-33) argues that Egyptian stone vessels could have been hollowed using up to three different types of stone drill heads throughout the chaîne opératoire: 1) a crescentshaped flint or chert bit; 2) a conical or circular bit, with two deep lateral grooves acting as hafting slots to host the wooden fork of a TRTD drill; and/or 3) figure-of-eight, hourglassshaped points, whose narrow waists would have served the same function. The latter type are: Because of the presence of lateral slots, types 2 and 3 may be considered variants of the same general type of bit. While conical points were used for drilling bores deeper than their width, the flatter figure-of-eight drill heads were used to make wider cavities, enlarging those previously made with other tools (Stocks 2003: 131-32). Moorey (1999: 55) notes that the crescent-shaped drill heads used in Egypt are unknown in Mesopotamia. In the ancient Near East, figure-of-eight drill heads are attested at Neolithic Jarmo, and were widely adopted from the late fourth millennium BC (e.g. at Ur, Uruk and Nineveh) and remained in use until Neo-Babylonian times in the mid first millennium BC (Moorey 1999: 56). Stocks (1993Stocks ( , 2003 also discusses the late fourth-/early third-millennium BC technology of stone-vessel production in Mesopotamia. He considers whether the techniques used were similar to those found in Egypt, comprising copper tubular bits used to make cylindrical cavities, followed by the use of figure-of-eight drill heads to enlarge them. Stocks argues that Mesopotamian stonecutters attached the figure-of-eight drill head to some form of TRTD drill. The few drill heads so far identified on sites of the eastern Iranian Plateau-at Shahr-i Sokhta, Konar Sandal South (Figure 4b  -have no deep, lateral slots and were probably fixed to the drill shaft in a different manner, so they were not the TRTD type. The only figure-of-eight drill bit from the Iranian Plateau known to the authors (Figure 4a) was found during excavation of a secondary refuse layer rich in artefacts, on the floor of a building at site ABC at Tal-e Malyan (ancient Anshan) in Fars Province, south-western Iran, dating to the Middle Banesh period (Sumner 2003: fig. 42i). A radiocarbon sample from this layer (P-2334) dates to 3350-2920 cal BC (at 95.4% confidence) and 3340-3020 BC (at 68.2% confidence) (Sumner 2003: tab. 13). This figure-of-eight drill head was made of a very fine-grained, light brownish-grey stone, with a triangular section, a functional convex surface with thin striations, and pecked depressions on the other two sides.
The other known drill heads from the eastern Iranian Plateau come from Shahr-i Sokhta and Konar Sandal South. The tool illustrated in Figure 4b, from Shahr-i Sokhta (Ciarla & Bökönyi 1985), was reportedly a surface find recovered along with four similar objects. It has a sub-cylindrical body and a bulbous end, and bears rotation marks. The enlarged head of the tool concentrated pressure and friction at the base of the drilled cavity. In contrast, the tool shown in Figure 4c, also from Shahr-i Sokhta, is made of a fine granite and might have been used for grinding and enlarging the entire inner surface of larger, conical cavities. Lateral slots would make these tools similar to the figure-of-eight drill heads, but slots are not    apparent in previously published illustrations. Finally, Figure 4d depicts a double-ended porphyry tool found at the settlement of Konar Sandal South (Rafifar et al. 2008), currently radiocarbon-dated to between c. 2800 and 2400 cal BC (Madjidzadeh & Pittman 2008: 76). This small number of examples represents the sum of our knowledge of stone-vessel production tools from eastern Iran. The 12 examples from Hajjiabad-Varamin therefore add substantially to the regional dataset. Drilling stone vessels in third-millennium BC Iran: new evidence from Hajjiabad-Varamin

The stone drill heads from Hajjiabad-Varamin
The surface of the production area at Hajjiabad-Varamin is characterised by thousands of broken stone vessels and other waste. Among this material, we report, in detail, on nine of the 12 drill heads so far identified. These are described below, grouped according to lithology.

Chert
1) A crescent-shaped or trapezoidal lithic object measuring 77 × 49 × 27mm and made of a fine-grained, reddish-brown chert, with partial bleaching on its surface ( Figure 5). This object has no obvious wear marks, although the two concave sides have been symmetrically battered. Its form closely resembles the lunate examples from Egypt, but its function as a drill bit must remain hypothetical, as this is the only example of this type so far found at the site. 2) A thick, cone-like drill head, measuring 66 × 65 × 42mm, made of a very fine, green chert ( Figure 6). The tool was flaked from a pebble, using a process similar to a core preparation sequence. A large portion of the original cortex is visible on two sides. The upper side was also reduced through a crested ridge preparation process. The active, curved part of the point is 19mm deep and 67mm wide. Its surface retains cortex, but the abrading edge of the point seems to have been prepared by light hammering, possibly with a copper tool. 3) A chert tool with cortical patches, indicating that it was obtained from a flat pebble that had been reduced by perimetral flaking to produce its regular, triangular form. If hafted as illustrated in Figure 7a and c, the point could have rotated, so that the two active faces laterally abraded a wider cavity; if hafted differently, with the active ends (emphasised by black dots) in a vertical, axial setting, it could have been used to bore the vessel to a greater depth. Thus, by alternating its hafting, the tool could have been used to hollow out a vessel to different depths and diameters. As with the example illustrated in Figure 6, the continuous active edge (Figure 7d), which is rather worn, was intentionally pecked by light hammering.

Reddish-grey porphyry
Five objects in reddish-grey, coarse-grained rock were identified visually as porphyry ( Figures  8 & 9). These represent a possible preform and four drill heads. Figure 8a shows a thick flake (118 × 98 × 59mm), bifacially flaked by heavy blows and rectangular-trapezoidal in section.
As the drill heads are made of the same rock and are of comparable size, this bifacial artefact is likely to have been an unfinished point. Figure 8b-c illustrates artefacts used as heavy-duty, rotating drill heads. Figure 8b shows a thick, dihedral flake (91 × 88 × 41mm), whose damaged, rotating end is a rounded, smooth cone, 14mm deep × 41mm wide. Figure 8c shows a thick flake (104 × 76 × 53mm), detached from a larger block or boulder. It has an approximately triangular section and retains cortex on one side. Its main end is rounded by friction, with faint rotation lines. Part of a second, rounded tip is visible on the opposing side, indicating that both ends of the drill were used. Figure 9a shows a thick flake (76 × 69 × 53mm) with a triangular section. Cortex survives on one side. The tip, which is broken, is a deep cone and displays faint rotation lines. A small, rounded area remains on the opposing side, suggesting that the drill was used from both sides. The conical point is 31mm deep × 24mm wide. Figure 9b illustrates an object, measuring 92 × 83 × 76mm, made by flaking a larger, older tool with heavy blows. It has at least three highly polished surfaces. Three corners seem to have been used as rotating points. The main rotating end is a very shallow cone, measuring 12mm deep and 39mm wide.

Red lava
A distinctive tool, made of red lava ( Figure 10). It measures 63 × 45 × 42mm and has a cylindrical, slightly tapered upper hafting section, coming to a smooth, conical point (22mm deep, 36mm in diameter). There is a conical hole in the side of the hafting section, which would have held a removable plug to fix the drill head within a hollow, cylindrical drill shaft. The location of the hole so close to the cutting point suggests that the tool was worn beyond practical use. The cutting point is worn similar to the porphyry drill head (Figure 4d). Carefully shaped by chipping and grinding, it was probably designed for a very specific rotatory function, perhaps to deepen rather than widen cavities. No known parallels for this object have been found in the published literature.

Conclusions
We have presented evidence from the Bronze Age site of Hajjiabad-Varamin, suggesting that the area to the immediate east of the main mound was a craft-production area for the manufacture of stone vessels. We have not yet been able to apply the types of analytical techniques recently deployed, for example, at Shahr-i Sokhta (Boccuti et al. 2015), and the site awaits a full systematic surface collection. Here, however, we have provided comparisons with other sites across Egypt and Southwest Asia to elucidate the date and organisation of production.
In the absence of use-wear analysis, the brown chert crescent ( Figure 5) seems comparable to the crescent drill heads of the Naqada II period (mid fourth millennium BC) found at Hierakonpolis in Egypt (Hikade 2004: 185-87, figs 1.1 & 3-6). Later, in the third millennium BC, parallels exist among chert drill heads from the Old Kingdom workers' settlement of Heit el-Ghurab at Giza (Malak Eyad 2014: 31-32, images 2.4-2.5). The Hajjiabad-Varamin brown chert crescent also appears similar to the 'boat-shaped drills' from Al-Shaykh Sacid-Wadi Zabayda in Egypt, dating to the second-millennium BC New Kingdom (Willems et al. 2009: fig. 3B). Stocks (1993: 598) argues that "crescent-shaped flints … were used exclusively for cutting soft stone, for example, gypsum, without sand abrasive" and were therefore unsuitable for working calcite vessels (Stocks 2003: 139-40). The apparent absence or rarity of this type of drill head in Mesopotamia, combined with its isolated presence in the Halil Rud Valley, is notable. The current scarcity of evidence does not allow us to conclude whether this might be due to a documentary gap or, rather, reflects the type's lack of suitability for the local manufacturing process. Figure-of eight drill heads seem to be the most common type in both Egypt and Mesopotamia in the late fourth millennium BC. At Ur, Woolley noted: stone borers for hollowing stone vases … [are] common in the Uruk and Jamdat Nasr periods; the drill-point is a circular stone, flat on the top and curved underneath, and from each side a piece is cut out for attachment; the shaft of the drill would be made of two pieces of wood laid together (or one piece forked at one end … [that] gripped the stone drill head). (Woolley 1956: 14, fig. 5; see also Stocks 1993: fig. 2) In Egypt, heavy, quartzite figure-of eight drill heads with rotation marks on their abrading surfaces are reported from Hierakonpolis (mid fourth millennium BC) as vessel-making tools (Hikade 2004: 185-87 & figs 1.7-1.9). Other similar drill heads, dating to c. 3000 BC, have been found at Tell el-Farkha and at contemporaneous manufacturing sites (Jórdeczka & Mrozek-Wysocka 2012: 289-91 & figs 16-18). By the second millennium BC, the calcite vessel-manufacturing workshop of Al-Shaykh Sacid-Wadi Zabayda in Middle Egypt used an impressive array of different silicified limestone drill heads attested among more than 1000 finds. Classified into five groups (figure-of-eight, boat-shaped, vertically oblong, discoidal with flat underside, and bits with a shallow hollow), these drill heads hint at specialised functions in the local mass-production industry (Ilan 2016: fig. 11;after Willems et al. 2009: fig.  3). By contrast, figure-of-eight drill heads have not been recovered at third-millennium BC Hajjiabad-Varamin and they seem to be absent (or unrecognised) at Shahr-i Sokhta.
The technical convergence among drilling equipment in Egypt, Mesopotamia and Tal-i Malyan/Anshan, in Iran, is probably the result of the well-known but poorly understood sphere of exchange and cultural interaction between these regions in the late fourth millennium BC (see, for example, Ward 1964;Mark 1998;Joffe 2000). In this scenario, the technical/formal convergence of the late fourth millennium BC was followed, in the third and second millennia, by increasing adaptation to local stone varieties for making vessels of new, specific forms.
The diversity of the drill heads found at Hajjiabad-Varamin recalls that of the later, New Kingdom workshop of Al-Shaykh Sacid-Wadi Zabayda (Willems et al. 2009). In this latter context, the alternate use and shifting friction planes of the drill heads, alongside the use of copper tools, attests to a completely new, dynamic approach to stone drilling.
In the Halil Rud Valley, different types of drilling tools were also developed and used for distinct steps in the production cycle, perhaps on different types of rocks, and possibly in different periods. Along the Halil Rud Basin, experimentation with lithic technologies, including abrasive tools, was encouraged by the geological diversity of the region (Fouache 2008). Whether this expresses a specific south-eastern Iranian trend is currently unknown and can only be resolved by excavations to recover stratigraphic sequences and archaeometric analyses of lithic objects. Nevertheless, our study shows that the makers of drilling tools in eastern Iran were well aware of the properties of the local resources available for the production of the semi-precious stone vessels that circulated in third-millennium BC Mesopotamia.