1 Introduction
The 2-μm ultrafast fiber laser has wide application fields, such as in gas detection[ Reference Pal, Chen, Sen, Sun and Grattan 1 ], industrial material processing[ Reference Voisiat, Gaponov, Gečys, Lavoute, Silva, Hideur, Ducros and Račiukaitis 2 – Reference Geng, Yan, Shi and Qiu 4 ], medical surgery[ Reference Fried and Murray 5 ] and pumping mid-infrared (IR) optical parametric oscillators and optical parametric amplifiers[ Reference Fu, Xu, Liang, Shardlow, Shepherd, Alam and Richardson 6 , Reference Yao, Wang, Tomilov, Hoffmann, Ahmed, Liebald, Rytz, Peltz, Wesemann and Saraceno 7 ]. At present, the research on 2-μm ultrafast fiber lasers is heading in the direction of generating much shorter laser pulses, particularly to the few-cycle pulse regime, which can be employed to drive a water-window X-ray desktop coherent light source[ Reference Popmintchev, Chen, Popmintchev, Arpin, Brown, Ališauskas, Andriukaitis, Balčiunas, Mücke, Pugzlys, Baltuška, Shim, Schrauth, Gaeta, Hernández-García, Plaja, Becker, Jaron-Becker, Murnane and Kapteyn 8 ] and realize attosecond light pulse generation[ Reference Zhang, Vampa, Villeneuve and Corkum 9 ]. By now, the shortest pulse duration of 45 fs (6.7 optical cycles) has been directly realized from a Tm-doped fiber oscillator, but with a low average output power of only 13 mW[ Reference Nomura and Fuji 10 ]. The average power can be scaled up with a chirped pulse amplifier, while with the cost of a broadened pulse duration that typically is hundreds of femtoseconds, which arises from the spectrum narrowing effect[ Reference Ren, Slimen, Lousteau, White, Jung, Price, Richardson and Poletti 11 – Reference Chen, Xing, Zhang, Wang, Wei and Chang 16 ].
A fiber-based nonlinear pulse compressor, which relies on the nonlinear spectrum broadening process in the gas-filled hollow core fiber (HCF), Kagome-fiber or highly nonlinear fiber (HNLF), is the most efficient way to realize few-cycle laser pulses[ Reference Khazanov, Mironov and Mourou 17 – Reference Nisoli, De Silvestri and Svelto 19 ]. Among them, the HNLF possesses a large nonlinearity and can be employed for the compression of a small energy laser pulse with a high pulse repetition rate. Typically, the employed HNLF has a mode field diameter (MFD) either smaller than 4 μm or larger than 10 μm, both of which can be directly fused with standard single-mode fibers, and thus are favorable for constructing an all-fiber nonlinear pulse compressor without grating pairs or chirped mirrors for post pulse compression. Figure 1 summarizes the previously reported 2-μm all-fiber nonlinear pulse compressors. The shortest pulse duration of 13 fs (~2-cycle)[ Reference Butler, Gerz, Hofer, Xu, Gaida, Heuermann, Gebhardt, Vamos, Schweinberger, Gessner, Siefke, Heusinger, Zeitner, Apolonski, Karpowicz, Limpert, Krausz and Pupeza 20 ] and highest output power of 24.5 W[ Reference Gaida, Gebhardt, Stutzki, Jauregui, Limpert and Tünnermann 21 ] have been realized with a large MFD-HNLF. However, the large MFD-HNLF requires a driving laser pulse at the microjoule level. A small MFD-HNLF is suitable for realizing the nonlinear pulse compression of a nanojoule-level laser pulse with a high pulse repetition rate above 100 MHz. For example, pulse durations of less than 40 fs with the repetition rate of more than or approximately 100 MHz have been realized with small MFD-HNLF[ Reference Xing, Lesko, Umeki, Lind, Hoghooghi, Wu and Diddams 22 – Reference Xing, Kowligy, Lesko, Lind and Diddams 25 ]. Few-cycle laser pulses with the repetition rate of more than 100 MHz are beneficial for improving the signal-to-noise ratio in spectroscopy experiments[ Reference Griffith and De Haseth 26 ]. Besides that, such a pulse laser source also can be used for studying and controlling ultrafast charge transport in dielectrics[ Reference Schiffrin, Paasch-Colberg, Karpowicz, Apalkov, Gerster, Mühlbrandt, Korbman, Reichert, Schultze, Holzner, Barth, Kienberger, Ernstorfer, Yakovlev, Stockman and Krausz 27 ] and in semiconductors[ Reference Schubert, Hohenleutner, Langer, Urbanek, Lange, Huttner, Golde, Meier, Kira, Koch and Huber 28 ].
The small MFD-HNLF typically has a large nonlinear coefficient of more than 10 W–1 km–1 and a total dispersion close to zero. The MFD of HNLF is much less than that of standard single-mode fiber (8 μm at 1950 nm). The large mode-mismatching between them increases the thermal load and optical loss at the position of the fusing point, which limits the further power scaling of small MFD HNLF-based nonlinear pulse compressors. Besides that, the pulse splitting effect usually shows up due to the overdriven nonlinearity with a high driving laser pulse power, thus making the average output power in small MFD HNLF-based nonlinear pulse compressors limited within several hundreds of milliwatt (see Figure 1(b)). The corresponding pulse compression ratios are less than 6 (see Figure 1(a)).
The 2-μm normal dispersion fiber (NDF) possesses a large normal dispersion of 0.137 ps2/m and a moderate nonlinear coefficient of 2.68 W–1 km–1, which is smaller than that of the HNLF of 10 W–1 km–1 but larger than that of the standard single-mode fiber of 0.53 W–1 km–1. The input ultrafast laser pulse inside the NDF will be broadened in both the frequency and time domains, which lowers the peak power of the ultrafast laser pulse. This can prevent the pulse splitting effect induced by the overdriven nonlinearity and enable tolerating a higher driving laser power[ Reference Raabe, Feng, Witting, Demircan, Brée and Steinmeyer 29 ]. Simultaneously, considering the easy direct fusion of NDF with other standard single-mode fibers, it is very much expected to construct an all-fiber nonlinear pulse compressor. However, to the best of our knowledge, there is no report on an NDF-based all-fiber nonlinear pulse compressor at this moment.
In this paper, we develop an all-fiber nonlinear pulse compressor based on 2-μm NDF for the first time. A 450-fs long 2-μm laser pulse with a pulse repetition rate of 101.4 MHz is compressed to 35.1 fs, corresponding to 5.2 optical oscillation cycles. The pulse compression ratio is 13.7, which is more than two times larger than that of previously reported 2-μm all-fiber nonlinear pulse compressors operating in the high pulse repetition region of more than 100 MHz. The output average power exceeds 1 W, which is the highest average power never realized in previously reported 2-μm all-fiber nonlinear pulse compressors with a more than 100-MHz pulse repetition rate. The experimental results are further analyzed with the generalized nonlinear Schrödinger equation, showing good agreement with the simulated results.
2 Experimental results and discussion
Figure 2 presents a schematic diagram of the NDF-based all-fiber nonlinear pulse compressor. The ultrafast driving laser pulse is delivered from a Tm-doped fiber laser amplifier with a pulse repetition rate of 101.4 MHz (see Figure 3). The dispersion of the ultrafast laser pulse can be adjusted with a grating pair. The driving laser beam is collimated and fed into the following all-fiber nonlinear pulse compressor with a fiber collimator after transmitting through a half-wave plate. The pigtail of the input fiber collimator is a 19-cm long polarization maintaining fiber (PMF; Nufern, PM-SMF-10/130). Two pieces of NDFs (NDF1 and NDF2) with lengths of 28 and 15 cm are employed for nonlinear pulse compression. Between NDF1 and NDF2, a 40-cm long single-mode fiber (Corning, SMF-28) is used to balance the NDF1- and self-phase modulation (SPM)-induced up-chirp. The laser pulses are coupled out by another fiber collimator with a 22-cm long single-mode pigtail (SMF2). The parameters of the employed fibers are listed in Table 1. The optical spectrum and the pulse duration of the laser pulse are respectively measured with a spectrometer (APE, WaveScan USB) and an autocorrelator (APE, pulseCheck). The output power is recorded with a power meter (Thorlabs, S425C).
a CD: core diameter.
b MFD: mode field diameter.
c GVD: group velocity dispersion.
d γ is the nonlinear coefficient.
e NA: numerical aperture.
Figure 3 shows the characteristics of the ultrafast driving laser pulse for different average output powers. As the average power scales up, the laser spectrum is always centered at 2012 nm with the range covering from 2000 to 2020 nm (see Figure 3(a)). Once the average power exceeds 0.4 W and further goes to 2.14 W, the spectral bandwidth keeps around approximately 10 nm (see Figure 3(b)). The pulse duration of the driving laser pulse approaches less than 500 fs when the output power exceeds 0.2 W. The measured autocorrelation trace at the maximum average power of 2.14 W shows the shortest pulse duration of 436 fs, which approaches the Fourier transform limited (FTL) value of 425 fs by assuming a sech2 pulse shape.
Initially, the ultrafast driving laser pulse is slightly stretched to 450 fs by introducing a positive group delay dispersion (GDD) of +18,000 fs2. As the ultrafast driving laser pulse enters into the nonlinear pulse compressor, the up-chirped driving laser pulse can balance the polarization maintaining (PM) fiber-introduced anomalous dispersion of –18,000 fs2, thus ensuring a near-FTL laser pulse reaches the NDF1. The laser spectrum out of the fiber NDF1 is broadened to a range of 200 nm from 1900 to 2100 nm (blue dashed line in Figure 4(c) ), which is about 10 times broader than the ultrafast driving laser pulse. The 40-cm long single-mode fiber SMF1 behind NDF1 provides a negative GDD of –33,000 fs2, which can partly compensate the up-chirp inside the ultrafast laser pulse. Then the laser pulse enters into the 15-cm long NDF (NDF2), which additionally adds a positive GDD of +20,000 fs2. After passing through a 22-cm long single-mode fiber (SMF2) with a negative GDD of –17,800 fs2, the ultrafast laser pulse is coupled out of the nonlinear pulse compressor with an output collimator.
Figure 4(b) shows the output power of the all-fiber nonlinear pulse compressor versus the input driving laser power. As the average power of the ultrafast driving laser scales up to 2.14 W, the output power is linearly increased to 1.28 W with a power fluctuation of 0.26%. The corresponded power loss approaches approximately 40%, which mainly arises from the coupling loss (~8%) of the fiber collimator and the total mode-mismatching loss (~32%) of different fibers. With the increase of the input driving laser power, the nonlinear spectrum broadening effect is also enhanced (see Figure 4(b)). At the maximum output power, the output spectrum is extended to a spectral range of 300 nm from 1850 to 2150 nm, about 1.5 times larger than that measured behind NDF1 (see Figure 4(c)). The modulations on the top of the broadened spectrum are mainly attributed to the enhanced SPM effect and the PM fiber-induced birefringence filtering effect. The measured radio frequency spectrum shows a signal-to-noise ratio of 70 dB at 101.4 MHz. There are no obvious sub-peaks near the fundamental frequency comb, indicating that no strong pulse splitting effect occurs inside the all-fiber nonlinear pulse compressor.
Figure 5(a) gives the compressed pulse duration under different input powers. At the maximum input power, the measured autocorrelation trace is as presented in Figure 5(b). It shows that the shortest pulse duration is 35.1 fs by assuming a sech2 pulse shape, corresponding to a pulse compression ratio of 13.7, which is believed to be the largest value never realized in a previously reported 2-μm all-fiber nonlinear pulse compressor operating with a more than 100-MHz pulse repetition rate (see Figure 1). The pedestal at the bottom of the autocorrelation trace arises from the higher order dispersion, which cannot be compensated with the single-mode fiber. The realized pulse duration is expected to be further narrowed with a shorter pulse duration and a higher peak power of the driving laser.
For further investigating the evolution of the ultrafast driving laser pulse inside the nonlinear pulse compressor, a numerical model is established based on the generalized nonlinear Schrodinger equation (GNLSE)[ Reference Zayed and Al-Nowehy 30 ], which is given as follows:
The right terms simultaneously incorporate the nonlinear effects, including SPM, self-steepening and the stimulated Raman scattering effect. In the GNLSE, A is the slowly varying pulse envelope, z represents the propagation distance, а denotes the fiber loss, β 2 and β 3 are the second- and third-order dispersion parameters, respectively, ω 0 is the angular frequency of the driving laser pulse, T is the time delay relative to the driving laser pulse and γ is the nonlinear coefficient. Here, $S={\gamma}_1\left({\omega}_0\right)/\gamma \left({\omega}_0\right)$ corresponds to the effect of self-steepening, where ${\gamma}_1\left(\;\omega \right)= \mathrm{d}\gamma \left(\omega \right)/ \mathrm{d}\omega$ and ω 0 is the central angular frequency. The response function $R(t)=\left(1-{f}_{\mathrm{R}}\right)\delta (t)+{f}_{\mathrm{R}}{h}_{\mathrm{R}}(t)$ includes both the instantaneous electronic and delayed Raman contributions, with $\kern2pt{f}_{\mathrm{R}}=0.18$ representing the fractional contribution of the delayed Raman response. For the Raman response function of the silica fiber, ${h}_{\mathrm{R}}(t)={\tau}_1\left({\tau}_1^{-2}+{\tau}_2^{-2}\right)\exp \left(-t/{\tau}_2\right)\sin \left(t/{\tau}_1\right)$ , in which ${\tau}_1$ and ${\tau}_2$ are 12.2 and 32 fs, respectively[ Reference Lin and Agrawal 31 ].
According to the parameters of the employed fibers in Table 1, we simulate the pulse and spectrum at the position between different types of fiber inside the nonlinear pulse compressor, which are presented in Figure 6. The center wavelength of the driving laser pulse is set to 2012 nm with a full width at half maximum (FWHM) bandwidth of 9.7 nm. The pulse duration is slightly up-chirped to 450 fs similar to that in the experiment (see Figures 6(a) and 6(g)). When the driving laser pulse firstly goes through the PMF, the laser pulse is shortened to 433 fs by the PMF-provided negative GDD of –18,000 fs2 (see Figure 6(b)). The pulse spectrum slightly broadens from 9.7 to 10 nm (see Figure 6(h)). Once the laser pulse goes into the NDF (NDF1), the spectrum bandwidth broadens from 10 to 55 nm (see Figure 6(i)). Simultaneously, the laser pulse broadens from 433 to 615 fs, as shown in Figure 6(c). The laser pulse shows a parabolic shape, which is a typical characteristic of an ultrafast laser pulse propagating inside an NDF[ Reference Sukhoivanov, Iakushev, Shulika, Díez and Andrés 32 ]. As the laser pulse further goes out of the single-mode fiber (SMF1), which provides a negative GDD of –33,000 fs2, the laser pulse is compressed down to 180 fs (see Figure 6(d)). Simultaneously, the spectrum bandwidth further broadens to 67 nm (see Figure 6(j)). The narrowed laser pulse strengthens the nonlinear effect in the second NDF (NDF2), making the spectrum broaden to a range of 302 nm from 1811 to 2113 nm (see Figure 6(k)), which is about two times broader than that from NDF1. The pulse evolves into a parabolic shape with a pulse duration of 1040 fs, as shown in Figure 6(e). The residual chirp of the laser pulse is compensated with a second piece of single-mode fiber (SMF2) by providing a negative GDD of –17,800 fs2, finally resulting in a pulse duration of 32.5 fs (see Figure 6(f)). Figure 6(l) is the final spectrum, which is slightly broadened to a range of 311 nm from 1814 to 2125 nm. Further calculation shows the peak power of the output pulse is 0.39 MW. The critical power of self-focusing can be estimated as P cr ≈ λ 2/(2πn 0 n 2) = 22.6 MW, where n 0 = 1.45[ Reference Kitamura, Pilon and Jonasz 33 ] and n 2 = 1.94 × 10–20 m2/W[ Reference Patwardhan, Ginsberg, Chen, Jadidi and Gaeta 34 ] are the linear and nonlinear refractive indexes, respectively. Therefore, the pulse compression is completely induced by multiple compensation of the temporal chirp, and spatial effects make no contribution.
The simulated spectrum out of the first NDF (NDF1) matches well with the measured results (see Figures 7(a) and 7(b)). However, for the simulated spectrum out of SMF2, the intensity of the measured spectrum in the long wavelength region of more than 2050 nm is obviously lower than that of the simulation. This is attributed to the largely wavelength-dependent loss of the NDF, which is not considered in the simulation (Figure 7(c)). Besides that, the unaccounted PM fiber-induced birefringence filtering effect also results in a mismatching between the simulation and experiment. The red line in Figure 7(d) is the simulated 32.5 fs pulse, which approaches the FTL pulse of 27 fs (black line), corresponding to the residual GDD of +220 fs2. The obvious pedestal at the bottom of the simulated single pulse (red line in Figure 7(d)) arises from the uncompensated high-order dispersion and the spectral shape of the simulated spectrum (red line in Figure 7(c)).
3 Conclusion
Based on the NDF, which possesses a moderate nonlinearity and large normal dispersion, we construct an all-fiber nonlinear pulse compressor. With the all-fiber nonlinear pulse compressor, 450 fs, 101.4 MHz, 2-μm ultrafast driving laser pulses are compressed to 35.1 fs with a pulse compression ratio of 13.7, corresponding to only 5.2 optical oscillation cycles. The average output average power is 1.28 W. Both the pulse compression ratio and the output average power are the state-of-the-art values never achieved from previously reported more than 100-MHz 2-μm all-fiber nonlinear pulse compressors. Both the experiment and theory show that the NDFs are suitable for nonlinear pulse compression of 2 μm high-power laser pulses.
Acknowledgements
This work was supported by the National Natural Science Foundation of China (Nos. 62005144, 61775119, and 62175128); the Natural Science Foundation of Shandong Province (No. ZR2020QF096); the Qilu Young Scholar Program of Shandong University; the Taishan Scholar Foundation of Shandong Province (No. tsqn201812010); and the High-level Talent Cultivation Funds of the State Key Laboratory of Crystal Materials of Shandong University.