Today, robots can be found helping humans with their daily tasks. Some tasks require the robot to visit a set of locations in the environment efficiently, like in the Traveling Salesman Problem. As indoor environments are maze-like areas, feasible paths connecting locations must be computed beforehand, so they can be combined during the scheduling, which can be impracticable for real-time applications. This work presents an on-line Route Scheduling supported by a Fast Path Planning Method able to adjust pre-built paths. Experiments were carried out with virtual and real robots to evaluate time and quality of tours.

In this study, a novel kinematic calibration method is proposed to improve the absolute positioning accuracy of 6R robot. This method can achieve indirect compensation of the 25 parameters of modified Denavit–Hartenberg (MDH). The procedures of the method are threefold. Firstly, the 25-parameter errors model of MDH is initially established. However, only the errors of 10 parameters can be directly compensated in the 25-parameter errors model, since the inverse kinematics algorithm has to meet Pieper criterion. Subsequently, a calibration method is proposed to improve accuracy of the absolute position, which uses the Newton–Raphson method to transform the 25-parameter errors into 10-parameter errors (namely T-10 parameter model). Finally, the errors corresponding to 10 parameters in the T-10 parameters model are identified through the least square method. The calibration performances of T-10 parameters model are comprehensively validated by experimentation on two ER6B-C60 robots and one RS010N robot. After kinematic calibration, the average absolute positioning accuracy of the three robots can be improved by about 90%. The results indicate that the proposed calibration method can achieve more precise absolute positioning accuracy and has a wider range of universality.

In this paper, we propose a comparison of open-source LiDAR and Inertial Measurement Unit (IMU)-based Simultaneous Localization and Mapping (SLAM) approaches for 3D robotic mapping. The analyzed algorithms are often exploited in mobile robotics for autonomous navigation but have not been evaluated in terms of 3D reconstruction yet. Experimental tests are carried out using two different autonomous mobile platforms in three test cases, comprising both indoor and outdoor scenarios. The 3D models obtained with the different SLAM algorithms are then compared in terms of density, accuracy, and noise of the point clouds to analyze the performance of the evaluated approaches. The experimental results indicate the SLAM methods that are more suitable for 3D mapping in terms of the quality of the reconstruction and highlight the feasibility of mobile robotics in the field of autonomous mapping.

The phenomenal growth in the utilization of commercial unmanned aerial vehicles (UAVs) or drones leads to an urgent need for new approaches to ensure safety in the sky. Effective aerial surveillance requires patrolling swarms to react according to the various behaviors demonstrated by intruding swarms, but existing approaches are not practical when dealing with a large number of drones. Specifically, predicting the behaviors or planned paths of the intruding swarms is highly challenging as intruders may perform evasive strategies to avoid detection. Therefore, this work utilizes heuristic search strategies and investigates how various intruder behaviors affect the search performance. To investigate the search performance, a swarm versus swarm simulator is developed. Using the simulator, first, a comparative study is performed to evaluate how intruders’ behaviors can affect the performance of the patrolling swarm. Subsequently, three approaches, including single-objective optimization, multi-objective optimization, and Lévy flight, are compared in terms of their detection performance in a bounded space. The results suggest that multi-objective optimization outperforms both single-objective optimization and Lévy flight-based approaches. Furthermore, our results show that intruders have a lower chance of being tracked when moving in a dense crowd, and this finding reaffirms the schooling behaviors of fish. In a specific simulation scenario, the total percentage of detection is above 90%. However, the detection percentage is highly related to other factors such as search space, number of patrolling UAVs, and the intruders’ behaviors.

A robotic system constructed as a wheeled inverted pendulum (WIP) serves as an impressive demonstrator, since this kind of system is inherently nonlinear, unstable, and nonminimum phase. These properties may pose several difficulties, when it comes to control and trajectory planning. This paper shows a method for deriving a highly dynamic trajectory compliant with the system dynamics by means of solving an optimal control problem (OCP) using multiple shooting. The assumed task includes that the WIP should pass a height-restricting barrier. This can be achieved by leaning back or forth, in order to reduce the overall height of the WIP. The constraints inherent to the definition of this trajectory are nonconvex due to the shape of the robot. The constraint functions have a local minimum in an infeasible region. This can cause problems when the initial guess is within this infeasible region. To overcome this, a multistage approach is proposed for this special OCP to evade the infeasible local minimum. After solving four stages of subsequent optimization problems, the optimal trajectory is obtained and can be used as feedforward for the real system.

This paper presents backstepping control and backstepping constraint control approaches for a quadrotor unmanned aerial vehicle (UAV) control system. The proposed methods are applied to a Parrot Mambo drone model to control rotational motion along the $x$, $y$, and $z$ axes during hovering and trajectory tracking. In the backstepping control approach, each state of the system controls the previous state and is called “virtual control.” The last state is controlled by the real control input. The idea is to compute, in several steps, a control law that ensures the asymptotic stability of the system. The backstepping constraint control method, based on barrier Lyapunov functions (BLFs), is designed not only to track the desired trajectory but also to guarantee no violation of the position and angle constraints. Symmetric BLFs are introduced in the design of the controller. A nonlinear mathematical model is considered in this study. Based on Lyapunov stability theory, it can be concluded that the proposed controllers can guarantee the stability of the UAV system and the state converges asymptotically to the desired trajectory. To make the control robust, an adaptation law is applied to the backstepping control that estimates the unknown parameters and ensures their convergence to their respective values. Validation of the proposed controllers was performed by simulation on a flying UAV system.

Clinical observations and subjective judgements have traditionally been used to evaluate patients with muscular and neurological disorders. As a result, identifying and analyzing functional improvements are difficult, especially in the absence of expertise. Quantitative assessment, which serves as the motivation for this study, is an essential prerequisite to forecast the task of the rehabilitation device in order to develop rehabilitation training. This work provides a quantitative assessment tool for muscle weakness in the human upper limbs for robotic-assisted rehabilitation. The goal is to map the assessment metrics to the recommended rehabilitation exercises. Measurable interaction forces and muscle correlation factors are the selected parameters to design a framework for muscular nerve cell condition detection and appropriate limb trajectory selection. In this work, a data collection setup is intended for extracting muscle intervention and assessment using MyoMeter, Goniometer and surface electromyography data for upper limbs. Force signals and human physiological response data are evaluated and categorized to infer the relevant progress. Based upon the most influencing muscles, curve fitting is performed. Trajectory-based data points are collected through a scaled geometric Open-Sim musculoskeletal model that fits the subject’s anthropometric data. These data are found to be most suitable to prescribe relevant exercise and to design customized robotic assistance. Case studies demonstrate the approach’s efficacy, including optimally synthesized automated configuration for the desired trajectory.

The paper discusses the analytical expressions of a motion profile characterized by elliptic jerk. This motion profile is obtained through a kinematic approach, defining the jerk profile and then obtaining acceleration, velocity, and displacement laws by successive integrations. A dimensionless formulation is adopted for the sake of generality. The main characteristics of the profile are analyzed, outlining the relationships between the profile parameters. A kinematic comparison with other motion laws is carried out: trapezoidal velocity, trapezoidal acceleration, cycloidal, sinusoidal jerk, and modified sinusoidal jerk. Then, the features of these motion profiles are evaluated in a dynamic case study, assessing the vibrations induced to a second-order linear system with different levels of damping. The results show that the proposed motion law provides a good compromise between different performance indexes (settling time, maximum absolute values of velocity and acceleration).

A 10 kV distribution network is critical for ensuring power supply to residents and factories. The number of power maintenance operations is rapidly increasing, and aerial cable stripping is a significant branch of these routine maintenances. High-voltage cable stripping, on the other hand, is mostly done manually, which is inefficient and poses serious security risks. As a result, this paper proposes an automatic wire stripping robot for use in a 10 kV power grid. The mechanical structure of the stripping robot is designed for installation on the insulating rod based on the working environment of 10 kV overhead cables. The robot was subjected to electromagnetic field simulation, modal analysis, and rigid-flexible coupling analysis. Finally, the robot prototype is built, and the PID controller is designed. Stripping tests are performed on a cable with a cross-sectional area of 95, 120, 150, 240, and 300 mm2, and the results are satisfactory.

Instrument delivery is critical part in vascular intervention surgery. Due to the soft-body structure of instruments, the relationship between manipulation commands and instrument motion is non-linear, making instrument delivery challenging and time-consuming. Reinforcement learning has the potential to learn manipulation skills and automate instrument delivery with enhanced success rates and reduced workload of physicians. However, due to the sample inefficiency when using high-dimensional images, existing reinforcement learning algorithms are limited on realistic vascular robotic systems. To alleviate this problem, this paper proposes discrete soft actor-critic with auto-encoder (DSAC-AE) that augments SAC-discrete with an auxiliary reconstruction task. The algorithm is applied with distributed sample collection and parameter update in a robot-assisted preclinical environment. Experimental results indicate that guidewire delivery can be automatically implemented after 50k sampling steps in less than 15 h, demonstrating the proposed algorithm has the great potential to learn manipulation skill for vascular robotic systems.

This paper presents a mobile robot platform, which performs both indoor and outdoor localization based on an intelligent low-cost depth–inertial fusion approach. The proposed sensor fusion approach uses depth-based localization data to enhance the accuracy obtained by the inertial measurement unit (IMU) pose data through a depth–inertial fusion. The fusion approach is based on feedforward cascade correlation networks (CCNs). The aim of this fusion approach is to correct the drift accompanied by the use of the IMU sensor, using a depth camera. This approach also has the advantage of maintaining the high frequency of the IMU sensor and the accuracy of the depth camera. The estimated mobile robot dynamic states through the proposed approach are deployed and examined through real-time autonomous navigation. It is shown that using both the planned path and the continuous localization approach, the robot successfully controls its movement toward the destination. Several tests were conducted with different numbers of layers and percentages of the training set. It is shown that the best performance is obtained with 12 layers and 80% of the pose data used as a training set for CCN. The proposed framework is then compared to the solution based on fusing the information given by the XSens IMU–GPS sensor and the Kobuki robot built-in odometry solution. As demonstrated in the results, an enhanced performance was achieved with an average Euclidean error of 0.091 m by the CCN, which is lower than the error achieved by the artificial neural network by 56%.

This paper deals with kinematic modeling and motion control of a novel antenna pedestal based on parallel robotic mechanism. Its active joints are two sliders equipped with DC motors on a circular rail. The synchronous and asynchronous motions of the two sliders enable the antenna to rotate in azimuth and pitch. In order to solve the problem of trajectory deviation caused by nonlinear friction and other uncertain disturbances, the structure of the antenna is described at the beginning, and then, the kinematic model is established based on geometry method. Then, the fuzzy PI (FPI) control system is designed based on the position feedback of the driving slider to realize the trajectory tracking of the desired curve. Finally, the parameters of the FPI controller are optimized and validated by Simulink simulation experiments. The tracking performance and the effectiveness of the control algorithm on prototype are verified by experiments of typical trajectory following control.

This article presents modelling, simulation, and development of a wall-climbing robot based on coupled wheel and arm-type locomotion mechanism. The developed robot consists of two mobile modules connected with a robot arm mechanism. The actuation of the robot arm is inspired by inchworm locomotion, particularly during wall-to-wall transition, obstacle avoidance, and uneven surface locomotion. Easiness in the interchanging of wheel to arm and vice versa makes the robot more effective compared to previously developed wall-climbing robots. The kinematic and dynamic model for the proposed coupled wheel and arm locomotion concept has been established. A combination of particle swarm optimization (PSO) and proportional, integral, derivatives (PID) feedback control algorithm has been developed using MATLAB to simulate the different cases of robot motions. The developed prototype of the wall-climbing robot is used to verify the coupled wheel and arm locomotion concept in various wall climbing scenarios. The simulation and experimental findings show good comparisons and validate the model-based design of the wall-climbing robot.

The research of parallel mechanism (PM) configuration involves many problems. From topology to configuration, dimensional constraint, etc., how to establish the relationship between topology and configuration with effective methods is a long-term challenge for the configuration design. In this paper, the chemical molecular spatial structure (CMSS) is linked with the configuration of symmetrical parallel mechanism (SPM). Starting from the methane molecule (CH4), a spatial structural topological relation is obtained. Based on graph theory and the spatial structural topological relation, a new expression method with topological graph and its kinematic pair adjacency matrix for spatial SPM is proposed. Then, the expression and analysis for the characteristics of spatial SPM are obtained. Finally, by taking the 3-RPS PM and the 3-RRC PM as examples, the effectiveness and corresponding consistency of the proposed expression method are successfully verified. The proposed new expression method paves the way for the subsequent digital and automated design and analysis of the SPM configuration.

Modules are requisite for the realization of modular reconfigurable manipulators. The design of modules in literature mainly revolves around geometric aspects and features such as lengths, connectivity and adaptivity. Optimizing and designing the modules based on dynamic performance is considered as a challenge here. The present paper introduces an Architecture-Prominent-Sectioning (APS) strategy for the planning of architecture of modules such that a reconfigurable manipulator possesses minimal joint torques during its operations. Proposed here is the transferring of complete structure into an equivalent system, perform optimization and map the resulting arrangement into possible architecture. The strategy has been applied on a set of modular configurations considering three-primitive-paths. The possibility of getting advanced/complex shapes is also discussed to incorporate the idea of a modular library.

Robotic guides take visitors on a tour of a facility. Such robots must always know the position of the visitor for decision-making. Current tracking algorithms largely assume that the person will be nearly always visible. In the robotic guide application, a person’s visibility could be often lost for prolonged periods, especially when the robot is circumventing a corner or making a sharp turn. In such cases, a person cannot quickly come behind the limited field of view rear camera. We propose a new algorithm that can track people for prolonged times under such conditions. The algorithm is benefitted from an application-level heuristic that the person will be nearly always following the robot, which can be used to guess the motion. The proposed work uses a Particle Filter with a ‘follow-the-robot’ motion model for tracking. The tracking is performed in 3D using a monocular camera. Unlike approaches in the literature, the proposed work observes from a moving base that is especially challenging since a rotation of the robot can cause a large sudden change in the position of the human in the image plane that the approaches in the literature would filter out. Tracking in 3D can resolve such errors. The proposed approach is tested for three different indoor scenarios. The results showcase that the approach is significantly better than the baselines including tracking in the image and projecting in 3D, tracking using a randomized (non-social) motion model, tracking using a Kalman Filter and using LSTM for trajectory prediction.

Performance indexes are a powerful tool to evaluate the behavior of industrial manipulators throughout their workspace and improve their performance. When dealing with intrinsically redundant manipulators, the additional joint influences their performance; hence, it is fundamental to consider the influence of the redundant joint when evaluating the performance index. This work improves the formulation of the kinematic directional index (KDI) by considering redundant manipulators. The KDI represents an improvement over traditional indexes, as it takes into account the direction of motion when evaluating the performance of a manipulator. However, in its current formulation, it is not suitable for redundant manipulators. Therefore, we extend the index to redundant manipulators. This is achieved by adopting a geometric approach that allows identifying the appropriate redundancy to maximize the velocity of a serial manipulator along the direction of motion. This approach is applied to a 4-degree-of-freedom (DOF) planar redundant manipulator and a 7-DOF spatial articulated one. Experimental validation for the articulated robot is presented, demonstrating the effectiveness of the proposed method and its advantages.

This article presents a review of the platform configuration and dynamic of obstacle-surmounting unmanned ground vehicles (UGVs). For now, unmanned systems have emerged as a result of the rapid advancement of artificial intelligence and modern manufacturing techniques both domestically and internationally. The research on unmanned systems has been improved a lot. The UGV platform can execute transportation, recurring, and military tasks independently. For the high-level self-control, adaption, and maneuverability abilities, the UGV platform has been applied in the military, industry, and other special fields widely. The UGV platform usually performs tasks in an unstructured environment, so the all-terrain performance becomes a key factor restricting their operating efficiency and reliability. A brief literature review of the UGV platform is carried out in this article.

A novel concept—the contact-based landing on a mobile platform—is proposed in this paper. An adaptive backstepping controller is designed to deal with the unknown disturbances in the interactive process, and the contact-based landing mission is implemented under the hybrid force/motion control framework. A rotorcraft aerial vehicle system and a ground mobile platform are designed to conduct flight experiments, evaluating the feasibility of the proposed landing scheme and control strategy. To the best of our knowledge, this is the first time a rotorcraft unmanned aerial vehicle has been implemented to conduct a contact-based landing. To improve system autonomy in future applications, vision-based recognition and localization methods are studied, contributing to the detection of a partially occluded cooperative object or at a close range. The proposed recognition algorithms are tested on a ground platform and evaluated in several simulated scenarios, indicating the algorithm’s effectiveness.

Fiber winding reinforcement is widely used in soft robotic manipulators actuated by pressurized fluids. However, the specific effect of each type of winding on the bending motion of a tubular soft robotics manipulator with three chambers has not been explored widely. We present the development of precise finite element (FE) simulations and investigate the effect of helical fiber winding parameters on the bending motion of a two-degree-of-freedom manipulator with three internal chambers. We first show the development of an FE simulation that optimizes convergence and computational time and precisely matches the behavior of soft robots in practice. Compared to single-chamber robots, simulating three-chamber designs is more challenging due to the complex geometry. We then apply our FE model to simulate all the parameter variations. We show that for helical winding with a constant pitch, the closer the center of a chamber is to the intersection of the windings, the lower the bending stiffness of the chamber is. To minimize bending stiffness variation in different bending directions, the optimal angle between the center of the first chamber and the intersection of the two helical windings are 0° and 12°. Reducing the pitch of the helical windings or using other types of windings (i.e., ring winding or six helical winding) reduces the stiffness variation across different bending directions. The FE simulations are compared with experiments showing that the model can capture complex bending behaviors of the manipulator, even though the estimation tends to be less accurate at higher bending angles.