Hostname: page-component-848d4c4894-p2v8j Total loading time: 0.001 Render date: 2024-05-15T23:03:21.222Z Has data issue: false hasContentIssue false
  • English
  • Français

The Heat Transfer Performance of Porous Gas Turbine Blades

Published online by Cambridge University Press:  04 July 2016

F. J. Bayley  and
A. B. Turner
F. J. Bayley
Affiliation:
University of Sussex, Applied Sciences Laboratory
A. B. Turner
Affiliation:
University of Sussex, Applied Sciences Laboratory
Get access Rights & Permissions [Opens in a new window]

Extract

It is well known that the performance of the practical gas turbine cycle, in which compression and expansion are non-isentropic, is critically dependent upon the maximum temperature of the working fluid. In engines in which shaft-power is produced the thermal efficiency and the specific power output rise steadily as the turbine inlet temperature is increased. In jet engines, in which the gas turbine has so far found its greatest success, similar advantages of high temperature operation accrue, more particularly as aircraft speeds increase to utilise the higher resultant jet velocities. Even in high by-pass ratio engines, designed specifically to reduce jet efflux velocities for application to lower speed aircraft, overall engine performance responds very favourably to increased turbine inlet temperatures, in which, moreover, these more severe operating conditions apply continuously during flight, and not only at maximum power as with more conventional cycles.

Type
Supplementary Papers
Information
The Aeronautical Journal , Volume 72 , Issue 696 , December 1968 , pp. 1087 - 1094
Copyright
Copyright © Royal Aeronautical Society 1968 

Access options

Get access to the full version of this content by using one of the access options below. (Log in options will check for institutional or personal access. Content may require purchase if you do not have access.)

References

1. Schmidt, E. H. N. Heat transmission by natural convection at high centrifugal acceleration in water cooled gas turbine blades. General Discussion on Heat Transfer, IMechE/ASME, 1951.Google Scholar
2. Cohen, H. and Bayley, F. J. Heat transfer problems of liquid-cooled gas-turbine blades. Proc IMechE, Vol 169, No 53, 1955.Google Scholar
3. Brown, T. W. F. Development of the long life marine gas turbine. CIMAC Conference, Zurich, 1957.Google Scholar
4. Duwez, P. and Wheeler, H. L. Jnr, Experimental study of cooling by injection of a fluid through a porous material. Journal Aero Sciences, Vol 15, No 9, Sept 1948.Google Scholar
5. Livingwood, J. and Eckert, E. R. G. Calculation of transpiration cooled gas turbine blades. Trans ASME, Vol 75, No 7, October 1953.Google Scholar
6. Staniforth, R. A theoretical note on effusion-cooled gas turbine blades. NGTE Memo No M158, October 1952.Google Scholar
7. Grootenhuis, P. The mechanism and application of effusion cooling. J Roy Aero Soc, Vol 63, No 578, Feb 1959.Google Scholar
8. Andrews, S. J., Ogden, H. and Marshall, J. Some experiments on an effusion-cooled turbine nozzle blade. NGTE, Note No NT132, May 1954.Google Scholar
9. Donoughue, P. L. and Diaguila, A. J. Exploratory engine test of transpiration-cooled turbine rotor blade with wire cloth shell. NACA E53K27, January 1954.Google Scholar
10. Grootenhuis, P., Mackworth, R. C. A. and Saunders, O. A. Heat transfer to air passing through heated porous metals. General Discussion on Heat Transfer, IMechE/ASME, 1951.Google Scholar
11. Kelley, J. B. and L'Ecuyer, M. R. Transpiration cooling—its theory and application. Report No TM-66-5, JPC 422. Jet Propulsion Centre, Purdue University, June 1966.Google Scholar
12. Hodge, R. L. A turbine nozzle cascade for cooling studies. ARCCP No 492, 493, May 1958.Google Scholar
13. Kutateladze, S. S. and Leont'ev, A. I. Turbulent boundary layers in compressible gases. Translated by Spalding, D. B., Edward Arnold Ltd, London, 1964.Google Scholar
14. Romanenko, P. N., Kharchenko, V. N. and Semenov, Yu P. The effect of coolant injection into turbulent boundary layers on heat transfer and friction. Inter national Chemical Engineering, Vol 6, No 4, Oct. 1966.Google Scholar
15. Ainley, D. G. An experimental single-stage air-cooled turbine. Part II. Proc IMechE, May 1953.Google Scholar
16. Wilson, D. G. and Pope, J. A. Convective heat transfer to gas turbine blade surfaces. Proc IMechE, August 1954.Google Scholar