Hostname: page-component-848d4c4894-hfldf Total loading time: 0 Render date: 2024-06-05T10:12:55.802Z Has data issue: false hasContentIssue false
  • English
  • Français

Determination of Shear Stress at a Solder Paste/Stencil Interface

Published online by Cambridge University Press:  15 February 2011

Linda M. Head ,
Vincent Rogers ,
Chitteranjan Sahay  and
James Constable
Linda M. Head
Affiliation:
Binghamton University, Thomas J. Watson School of Engineering and Applied Science, P.O. Box 6000, Binghamton, NY 13902-6000
Vincent Rogers
Affiliation:
Binghamton University, Thomas J. Watson School of Engineering and Applied Science, P.O. Box 6000, Binghamton, NY 13902-6000
Chitteranjan Sahay
Affiliation:
Binghamton University, Thomas J. Watson School of Engineering and Applied Science, P.O. Box 6000, Binghamton, NY 13902-6000
James Constable
Affiliation:
Binghamton University, Thomas J. Watson School of Engineering and Applied Science, P.O. Box 6000, Binghamton, NY 13902-6000
Get access

Abstract

To create a model for the release process of solder paste during stencil printing for surface mount applications it is necessary to determine the shear stress developed at the interface between the solder paste and stencil sidewall. An experiment has been developed to determine the value of the shear stress for solder paste samples. For the purpose of this experiment a Micro-mechanical tester has been adapted and programmed to provide both a shear thinning cycle and a pull-off cycle that simulate aperture fill and stencil lift-off. The shear stress developed at the solder/stencil-sidewall interface is estimated from the data obtained during the pull-off portion of the Micro-mechanical test procedure. The micro-mechanical tester is fitted with a set of parallel plates that can be adjusted for plate separation and surface roughness.

The experiment consists of two parts: (1) the shear thinning cycle and (2) the horizontal pull-off. After application of the solder paste and adjustment of plate separation, a back and forth movement of the upper plate provides shear thinning of the paste. This step is necessary to simulate the shear thinning that occurs from the application of squeege pressure during aperture fill. The horizontal pull-off then simulates the lift-off step of the stencil printing procedure. During the horizontal pull-off data is. taken which allows calculation of the force developed as the upper plate is pulled away from the lower. Results from this experiment show the values of shear stress that develop during pull-off with a variation of surface treatments and plate separations.

This paper will present the experimental set-up, a description of the relationship between this experiment and the actual stencil lift-off process, and shear stress data that has been acquired for a variety of solder pastes and plate separations.

Type
Research Article
Information
MRS Online Proceedings Library (OPL) , Volume 323: Symposium J – Electronic Packaging Materials Science VII , 1993 , 425
Copyright
Copyright © Materials Research Society 1994

Access options

Get access to the full version of this content by using one of the access options below. (Log in options will check for institutional or personal access. Content may require purchase if you do not have access.)

References

1. Markstein, H.W., “Meeting Requirements of Fine Pitch Printing”, Electronics Packaging and Production, pp.34–39, March, 1993.Google Scholar
2. Latta, R. & Asla, J., “Reducing Solder Volume”, Circuits Assembly, pp.36–40, April, 1993.Google Scholar
3. Hutchins, C.L., “How Fine Can Fine-Pitch Printing Get?”, Surface Mount Technology, pp. 11–12, April, 1993.Google Scholar
4. Missele, C., “Subtleties of Stencil Printing Solder”, Surface Mount Technology, pp.21–24, April, 1993.Google Scholar
5. Morris, J.R. & Wojcik, T., “Stencil Printing of Solder Paste for Fine-Pitch Surface Mount Assembly”, IEEE Trans. on Components, Hybrids, and Manufacturing Technology, vol. 14, no. 3, pp.560–565, Sept. 1991.Google Scholar
6. Sahay, C., Head, L., Shreen, R., Dujari, P., Constable, J., & Westby, G., “Study of Print Release Process in Solder Paste Printing”, Presented at ASME Fall Meeting, Nov. 1993.Google Scholar
7. Niu, T.M., Burke, E.J., Black, W.E., and Case, J.R., “6-Axis Submicron Fatigue Tester”, Proc. of the 1992 Joint ASME/JSME Conf. on Electronic Packaging, vol. 2, pp.937–945.Google Scholar