This paper presents a numerical formulation targeting the rapid estimation of natural vibration characteristics of helicopter rotor blades. The proposed method is based on application of Lagrange’s equation of motion to the kinematics of blade flap/lag bending and torsion. Modal properties obtained from Bernoulli-Euler beam and classical torsional vibration theory, are utilised as assumed deformation functions in order to estimate the time variations of strain and kinetic energy for each degree of freedom. Integral expressions are derived, describing the generalised centrifugal force and torsional moment acting on the blade in terms of normal coordinates, for flap/lag transverse displacement and torsional deformation. Closed form expressions are provided for the direct analysis of hingeless, freely-hinged and spring-hinged articulated rotor blades. Results are presented in terms of natural frequencies and mode shapes for two small-scale rotor blade models. Extensive comparisons are carried out with experimental measurements and nonlinear finite element analysis. Predictions of resonant frequencies are also presented for two full-scale rotor blade models and the results are compared with established multi-body dynamics analysis methods. It is shown that, the proposed approach exhibits excellent numerical behaviour with low computational cost and definitive convergence characteristics. The comparisons suggest very good and in some cases excellent accuracy levels, especially considering the method’s simplicity, computational efficiency, and ease of implementation.

A key challenge in open rotor design is getting the optimum aerodynamics at both the cruise and take-off conditions. This is particularly difficult because the operation and the requirements of an open rotor are very different at cruise compared to takeoff. This paper uses CFD results to explore the impact of various design changes on the cruise and take-off flow-fields. The paper then considers how a given open rotor design is best operated at take-off to minimise noise whilst maintaining high thrust. The main findings are that various design modifications can be applied to control the flow features that lead to lost efficiency at cruise and increased noise emission at take-off. A breakdown of the lost power terms from CFD solutions demonstrates how developments in open rotor design have led to reduced aerodynamic losses. At take-off, the operating point of the open rotor should be set such that the non-dimensional lift is as high as possible, without causing significant flow separation. This can be achieved through suitable amounts of re-pitch and speed up applied to a design. Comparisons with fully three-dimensional CFD show that the amount of re-pitch required can be determined using simplified methods such as two-dimensional CFD and a Blade Element Method.

This paper describes a multidisciplinary robust optimisation framework for UAV conceptual design. An in-house configuration designer system is implemented to generate the full sets of configuration data for a well-developed advanced UAV analysis tool. A fully integrated configuration designer along with the UAV analysis tool ensures that full sets of configuration data are provided simultaneously while the UAV configuration changes during optimisation. The computational strategy for probabilistic analysis is proposed by implementing a central difference method and fitting distribution for a reduced number of Monte Carlo Simulation sampling points. The minimisation of a new robust design objective function helps to enhance the reliability while other UAV performance criteria are satisfied. In addition, the fully integrated process and a probabilistic analysis strategy method demonstrate a reduction in the probability of failure under noise factors without any noticeable increase in design turnaround time. The proposed robust optimisation framework for UAV conceptual design case study yields a more trustworthy prediction of the optimal configuration and is preferable to the traditional deterministic design approach. The high fidelity analysis ANSYS Fluent 13 is performed to demonstrate the accuracy of proposed framework on baseline, deterministic and RDO configuration.

Large transport aircraft are particularly susceptible to impact damage from runway debris thrown up by the landing gear. A methodology was developed to predict the trajectories of stones lofted by the nose wheel and subjected to aerodynamic forces due to the wake behind the nose landing gear and beneath the aircraft. In conjunction with finite element modelling of the stone/ground/tyre contact mechanics, an analytical model was used to perform a stochastic prediction of the trajectories of runway stones to generate impact threat maps which showed the relative likelihood of stones impinging upon various areas on the underside of a C-130 Hercules. The impact envelopes for the C-130 extended three to eighteen metres behind the nose wheel and two metres either side of the centre of the aircraft. The impact threat maps were especially sensitive to the values of the coefficients of lift and drag acting on the stone during its flight.

Flow separation results in many problems to single expansion ramp nozzle (SERN) and hypersonic vehicle. However, little research has been conducted on the separation patterns and their effects on SERN’s performance. In the present paper, the numerical simulation is adopted to get the intuitive results and help to analyse the separation phenomena in SERN thoroughly. The main separation pattern is the restricted shock separation (RSS) in SERN, and the free shock separation (FSS) only appears in a small range of the nozzle pressure ratio (NPR), which is much different from the axisymmetric rocket nozzle. Further CFD results show that the separation pattern transition makes great effects on the performance of SERN, especially the lift. Moreover, the performance of SERN has an extreme in the separation pattern transition because of the main jet impinging on the expansion ramp. The transitions occur in both the startup and shutdown processes but the critical nozzle pressure ratios of the separation pattern transitions are different, which leads to a hysteresis loop of SERN performance.

With the development of air traffic, flight delays happen frequently due to bad weather and traffic congestion. The problem can be solved partly by certain strategies, such as changing air routes. However, rerouting leads to a global imbalance in controller workload of current sectors and to an increase in co-ordination workload, and the workloads of some sectors may be beyond the controller’s ability to manage. Thus, airspace sectorisation is expected to migrate from the current static sectors to dynamically-changing ones capable of adapting to traffic demand. Besides addressing imbalance and controlling the increase in workload, the sectorisation has to meet additional geometric constraints such as convexity, connectivity, and minimum distance constraint.

ITA and EMBRAER are currently executing the research project Automation of Aircraft Structural Assembly (AASA) whose goal is to implement a robotic cell for automating the riveting process of aeronautical structures. The proposal described herein complements the AASA project, adds other manufacturing processes, namely sanding and polishing of aircraft surfaces. To implement the additional processes AASA project resources and facilities were used (robots and metrology systems) and devices designed and /or acquired to allow sharing of these resources. Among these, an Automatic Tooling Support for AERonautics structures (ATS_AER) was designed and built; also, a robot tool changer with high load capacity was acquired. The outcome of this research project is the evaluation of the feasibility of automating the processes of sanding and polishing metal surfaces in the aircraft manufacture using robots. The operating method adopted for surface treatment employed the ‘U’ type trajectory optimised to be run by a KUKA robot KR 500. The sanding process has been applied to aluminum metal sheet specimen sized 2•18ft2 (0•20m2) and used commercial 600 and 800 sandpaper. The automated sanding process yielded an average value of RA 0•48 ± 0•08 which is 25% more efficient when compared to the traditional, manual process whose average value of RA is 0•75 ± 0•51.

This paper examines three specific aspects pertaining to the trailing-edge flap (TEF) enabled swashplateless primary control of a helicopter. The study is based on a utility helicopter very similar to the UH-60A Blackhawk helicopter, with rotor torsion frequency reduced to 2·1/rev, and 20% chord TEFs extending from 70-90% span. The questions addressed in the paper are the power penalty due to aerodynamic drag associated with TEF control, the pitch-index required to limit the range of TEF deflections over variations in aircraft gross-weight and airspeed, and the influence of rotor RPM variation on swashplateless primary control. Results indicate that the power penalty associated with TEF enabled primary control at high speeds is in the range of 6-7%, due to increased drag on the advancing side in the region of the TEFs and at the blade tips. At low to moderate speeds the increase in power is 2-4% on average, more dependent on the pitch-index, and due to drag increase over most of the azimuth in the region of the TEFs. A variation in pitch-index from 16° for lower speeds and gross weights, to 20-22° for higher speeds and gross weights, would reduce the steady level flight TEF defection requirements to under ±3°, leaving sufficient control margin. Increase in rotor RPM does not increase directly increase thrust (as with a stiff-torsion rotor) but reduces the rotating torsion frequency, and together with the increased dynamic pressures increases the sensitivity to TEF control. At low to moderate speeds a 9% increase in RPM reduces the maximum TEF deflections required by about 1°, but is accompanied by a large increase in rotor power. Conversely, a 9% RPM reduction decreases rotor power required, but the TEF defections required increase by 1–1·5°.

This study aims to develop a practical discrete-event simulation model to analyse the single runway capacity of airports serving training flights under various operational scenarios. The number of operations per hour, average airborne and ground delays, queue lengths and runway utilisation are selected as performance measures for the analysis. The simulation model has been developed in ARENA in order to obtain a practical yet accurate analysis. The model can contribute to the efficient use of runway capacity as well as effective planning of flight training at airports.

The purpose of this paper is to describe the current status of open rotor noise prediction methods and to highlight future challenges in this area. A number of analytic and numerical methods are described which can be used for predicting ‘isolated’ and ‘installed’ open rotor tonal noise. Broadband noise prediction methods are also described and it is noted that further development and validation of the current models is required. The paper concludes with a discussion of the analytical methods which are used to assess the acoustic data collected during the high-speed wind-tunnel testing of a model scale advanced open rotor rig.

Stage separation is a critical technical issue for developing two-stage-to-orbit (TSTO) launch systems with widebody carrier aircraft that use air-breathing propulsion and launch vehicle stages that use rocket propulsion. During conceptual design phases, this issue can be addressed with a combination of engineering methods, computational fluid dynamics simulations, and trajectory analysis of the mated system and the launch vehicle after staging. The outcome of such analyses helps to establish the credibility of the proposed TSTO system and formulate a ground-based test programme for the preliminary design phase. This approach is demonstrated with an assessment of stage separation from the shuttle carrier aircraft. Flight conditions are determined for safe mated flight, safe stage separation, and for the launch vehicle as it commences ascending flight. Accurate assessment of aerodynamic forces and moments is critical during staging to account for interference effects from the proximities of the two large vehicles. Interference aerodynamics have a modest impact on the separation conditions and separated flight trajectories, but have a significant impact on the interaction forces.

The estimation of gas turbine engine weight during the preliminary or conceptual design phase is a key part of a Techno-economic Environmental Risk Analysis (TERA). Several methods that are available in the public domain are analysed and compared, in order to establish the physics driving them and their suitability for the weight estimation of modern gas turbine engines. Among the tested methods, only WATE managed to achieve acceptable accuracy for engine optimisation studies. This work demonstrates that the age and restrictions of existing ‘whole engine based’ methods, along with their dependency on old engine databases make them unsuitable for future and novel aero engines. A hybrid weight modelling approach is proposed as a solution permitting the creation of simple ‘whole engine based’ methods that do not depend on the availability of existing engine data, which are also subject to uncertainties and incoherencies.

The effect of the wake of a leading aircraft on a following aircraft is demonstrated by calculating the rolling motion consisting of three terms: (i) the free rolling motion due to initial bank angle and roll rate; (ii) the forced wake response due the rolling moment induced by the wake encounter; (iii) the forced control response due to aileron deflection to counter the wake vortex effects. It is shown that in the absence of control action, the roll rate of the following aircraft goes through a peak, and then decays, leading to a constant asymptotic bank angle; the latter is a measure of the magnitude of the wake effect, e.g. is larger for weaker damping. The exact analytical solution of the roll equation appears as a power series of a damping factor, whose coefficients are exponential integrals of time; it is shown that the first two terms give an accuracy better than 2%. The theory is used to simulate 15 combinations of wake vortex encounters between leading and following aircraft in the five ICAO/FAA weight categories: light, medium, heavy, special (B757) and very large (A380).

This paper presents a novel framework, based on traditional system safety modelling approaches, for the representation and comparison of airworthiness aviation frameworks. A disparate array of military airworthiness frameworks have emerged due to a lack of standardisation and the absence of a recognised organisation needed for the harmonisation of military regulatory frameworks.. The complexity and subsequent cost in inter-agency recognition of existing certification programs has led to the establishment of a European forum of military airworthiness authorities. The forum is working towards establishing a common regulatory framework across its European member states. The common framework provides the systematic basis for a certification of military aircraft that can be readily recognised by all of the member states. This will have many cost and efficiency benefits for the EU. The framework and recognition process have recently been accepted as a method for establishing recognition outside of Europe, with some identified shortfalls. This paper establishes a method for overcoming these shortfalls for nations outside of europe. The Product-Behaviour-Process (PBP) Bow-Tie, which is a novel application of the traditional bowtie risk modelling tool, derives test points that capture the airworthiness attestations for the high-level engineering lifecycle processes of design, production and maintenance. The proposed framework is used to provide a comparison between the Australian Defence Force and United States Army regulatory frameworks. The comparative case-study clearly demonstrates the benefit of the PBP Bow-Tie model in its ability to systematically represent the disparate regulatory frameworks. A novel representation of the output is also described, which facilitates a visual comparison of the results. The application of the PBP Bow-Tie framework to the case-study of regulatory frameworks reveals significant differences that need to be addressed in order for inter-agency recognition.

This paper presents the development and testing through simulation of an integrated scheme for aircraft sub-system failure detection and identification (FDI) based on the artificial immune system (AIS) paradigm augmented with artificial neural networks. The features that define the self within the AIS paradigm include neural estimates of the angular accelerations produced by the abnormal conditions. The simulation environment integrates the NASA Generic Transport Model interfaced with FlightGear. A hierarchical multi-self strategy was investigated for developing FDI schemes capable of handling malfunctions of a variety of aircraft sub-systems. The performance of the FDI scheme has been evaluated in terms of false alarms and successful detection and identification over a wide flight envelope and for several actuator and aerodynamic surface failures. For all cases considered, the performance was very good, confirming the potential of the AIS paradigm augmented with the proposed neural network-based approach for feature definition to offer a comprehensive solution to the aircraft sub-system FDI problem.

An analysis, based upon exact relations and previously published approximate relations, is presented. It describes the connection between changes in aircraft weight and changes in the energy to revenue work ratio (ETRW), which, for a given aircraft on a given route, correspond to changes in trip fuel burn. This is used to establish the link between weight saving and fuel burn improvement at both the total aircraft and the component levels. The analysis is then extended to address the impact of trading weight savings anywhere on the aircraft for increased wing aspect ratio, whilst the aircraft total weight remains the same. It is shown that, for flights in excess of about 350 km, if saving fuel is the objective and provided that all the aerodynamic design and airworthiness requirements can be met, it is better to trade weight saving for increased aspect ratio. In general, the ratio of fuel burn reductions for traded to non-traded weight varies with aircraft size, design range, distance flown and payload carried, with the maximum values, for typical operational payloads, ranging from 2•8, for the smaller aircraft, to 2•2 for the largest aircraft, with medium haul operations deriving the largest benefit. It is estimated that, over the past 50 years, about 10% of the operational empty weight has been traded for increased aspect ratio, giving close to a 20% improvement in ETRW. Finally, estimates are produced for the impact of weight reduction and traded weight reduction on the fuel burn for the current global feet.

This paper focuses on the trajectory planning for a UAV on a low altitude terrain following/threat avoidance (TF/TA) mission. Using a grid-based approximated discretisation scheme, the continuous constrained optimisation problem into a search problem is transformed over a finite network. A variant of the Minimum Cost Network Flow (MCNF) to this problem is then applied. Based on using the Digital Terrain Elevation Data (DTED) and discrete dynamic equations of motion, the four-dimensional (4D) trajectory (three spatial and one time dimensions) from a starting point to an end point is obtained by minimising a cost function subject to dynamic and mission constraints of the UAV. For each arc in the grid, a cost function is considered as the combination of the arc length, fuel consumption and flight time. The proposed algorithm which considers dynamic and altitude constraints of the UAV explicitly is then used to obtain the feasible trajectory. The resultant trajectory can increase the survivability of the UAV using the threat region avoidance and the terrain masking effect. After obtaining the feasible trajectory, an improved algorithm is proposed to smooth the trajectory. The numeric results are presented to verify the capability of the proposed approach to generate admissible trajectory in minimum possible time in comparison to the previous works.

The paper presents the estimation of lateral-directional aerodynamic derivatives (parameters) using conventional and neural based methods from real flight data of Hansa-3 aircraft. The conventional methods such as least squares (LS) and maximum likelihood (ML) require an a priori postulation of mathematical model to estimate the parameters. Whereas the neural-based method such as Neural-Gauss-Newton (NGN) is an algorithm that utilises feed forward neural network and Gauss-Newton optimisation to estimate the parameters and does not require any a priori postulation of mathematical model or solution of equations of motion. In the paper, the LS, ML and NGN methods are applied to lateral-directional flight data in order to estimate parameters. The results obtained in terms of lateral-directional aerodynamic derivatives are reasonably accurate to establish LS, ML and NGN as parameter estimation methods along with NGN method having an additional advantage of non-requirement of a priori mathematical model. The paper also highlights the effect of different types of control inputs on parameter estimation. For this, three types of control inputs were used to generate real flight data. The ailerons and rudder were deflected in the first, the ailerons were deflected while keeping rudder at trim condition in the second and the rudder was deflected while keeping ailerons at trim condition in the third type of control input to generate the real flight data. The paper presents the effect of three different types of control inputs in terms of aerodynamic parameters estimated through conventional and neural based methods using flight data generated through these inputs.

Aerodynamic performance degradation has been considered a critical hazard to aircraft due to flying in heavy rain. In this work, a two-way momentum coupled Eulerian-Lagrangian approach is developed to study the aerodynamic performance of a two-dimensional (2D) transport-type NACA 64-210 cruise and landing configuration aerofoil as well as a three-dimensional (3D) NACA 64-210 cruise configuration rectangular wing in heavy rain environment. Raindrop impacts, splashback and formed water film are modeled. The steady-state incompressible air flow field and the raindrop trajectory are calculated alternately by incorporating an interphase momentum coupling term through a curvilinear body-fitted grid surrounding the aerofoil/wing. Our simulation results agree well with the experimental results and show significant aerodynamic penalties for all the test cases in heavy rain. Rain-induced premature boundary-layer transition and separation are observed and details of the raindrop splashback effect on the boundary layer are examined. A 1° rain-induced decrease in stall angle-of-attack is predicted. An uneven water film upon the wing surface is observed and its effect on the wing surface roughness is also examined.

Visually coupled systems such as helmet mounted displays are designed to improve aircrew situational awareness by providing timely flight, targeting and other information overlaid on real or sensor-derived views of the external environment. Data can be presented in monocular, biocular or binocular fashion and are associated with visual conflicts and potential ophthalmic problems. Restricted sensor spectrum, limits of resolution, inherent system latency, the displaced visual input from remote sensors and restricted field of view may contribute to ophthalmic symptoms in aircrew. Disruption to binocularity and reliance on monocular cues for depth perception and hyperstereopsis from sensor-induced convergence disparity may cause distance estimation problems, whereas inappropriate accommodative stimuli and ocular dominance factors are common causes of eyestrain. Binocular rivalry from discordant imagery to each eye may compromise visual performance via several mechanisms. This article discusses the potential visual problems associated with visually coupled systems and the challenges of integrating complex systems with the aircrew interface.