Hostname: page-component-848d4c4894-wg55d Total loading time: 0 Render date: 2024-05-01T00:07:24.775Z Has data issue: false hasContentIssue false
  • English
  • Français

Internal friction and torsional creep behavior of chemically vapor deposited boron nitride

Published online by Cambridge University Press:  31 January 2011

Giuseppe Pezzotti ,
Hans-Joachim Kleebe ,
Ken'ichi Ota  and
Toshihiko Nishida
Giuseppe Pezzotti
Affiliation:
Department of Materials, Kyoto Institute of Technology, Matsugasaki, Sakyo-ku, 606 Kyoto, Japan
Hans-Joachim Kleebe
Affiliation:
Institut für Materialforschung, Universität Bayreuth, D-95440 Bayreuth, Germany
Ken'ichi Ota
Affiliation:
Institute of Scientific and Industrial Research, Osaka University, Ibaraki-shi, Mihogaoka 8–1, 561 Osaka, Japan
Toshihiko Nishida
Affiliation:
Department of Materials, Kyoto Institute of Technology, Matsugasaki, Sakyo-ku, 606 Kyoto, Japan
Get access

Abstract

Dense hexagonal BN processed via chemical vapor deposition (CVD) was tested with respect to damping, shear modulus, and torsional creep rate up to temperatures as high as ≈2300 °C. The microstructural characteristics of the material both before and after creep testing were studied by high-resolution electron microscopy (HREM). The CVD process yields a homogeneous nanosized microstructure with no other secondary phase detectable. Damping experiments revealed no plastic relaxation during testing up to ≈2000 °C, which is consistent with the fact that also no creep deformation could be detected below such a high temperature. Small porosity and an increased amorphization process were noted by HREM inspection after stress exposure at ≈2300 °C. These phenomena may be responsible for both the enhanced damping capacity and the creep rate of the material which, in the range of the present testing conditions, seems to follow the simple viscoelastic behavior of a Maxwell solid.

Type
Articles
Information
Journal of Materials Research , Volume 13 , Issue 12 , December 1998 , pp. 3453 - 3457
Copyright
Copyright © Materials Research Society 1998

Access options

Get access to the full version of this content by using one of the access options below. (Log in options will check for institutional or personal access. Content may require purchase if you do not have access.)

References

1.Takigawa, H., in Isostatic Pressing, edited by Koizumi, M. and Nishihara, M. (Elsevier Applied Science, London, 1991), pp. 181–294.Google Scholar
2.Larker, H., Adlerborn, J., and Bohman, H., “Fabrication of Dense Silicon Nitride Parts by Hot Isostatic Pressing,” SAE Technical Paper No. 770335 (Society of Automotive Engineers, Warrendale, PA, 1977).Google Scholar
3.Honma, K., Okada, H., Fujikawa, T., and Tatsuno, T., Yogyo Kyokaishi 95 (2), 229–234 (1987).Google Scholar
4.Nezuka, K., Miyamoto, Y., and Koizumi, M., in Proc. Int. Conf. of Hot Isostatic Pressing—Theories and Applications, edited by Garvare, T. (Centak Publishing, Luleå, Sweden, 1988), pp. 359–365.Google Scholar
5.Tanaka, I., Pezzotti, G., Okamoto, T., and Miyamoto, Y., J. Am. Ceram. Soc. 72 (9), 1656–1660 (1989).CrossRefGoogle Scholar
6.Pezzotti, G., J. Am. Ceram. Soc. 76 (5), 1313–1320 (1993).CrossRefGoogle Scholar
7.Pezzotti, G., Ota, K., and Kleebe, H-J., J. Am. Ceram. Soc. 79 (9), 2237–2246 (1996).CrossRefGoogle Scholar
8.Pezzotti, G. and Ota, K., J. Am. Ceram. Soc. 80 (3), 599–603 (1997).CrossRefGoogle Scholar
9.Pezzotti, G., Ota, K., and Kleebe, H-J., J. Am. Ceram. Soc. 80 (9), 2341–2348 (1997).CrossRefGoogle Scholar
10.Yeckley, R. L. and Siebein, K. N., in Proc. Third Int. Symp. on Ceramic Materials and Components for Engines, Las Vegas, NV, November 27–30, 1988, edited by Tennery, V. J. (The American Ceramic Society, Westerville, OH, 1989), pp. 751–765.Google Scholar
11.Ota, K. and Pezzotti, G., Philos. Mag. A 73 (1), 223–235 (1996).Google Scholar
12.Kessler, H., Kleebe, H-J., Cannon, R. W., and Pompe, W., Acta Metall. Mater. 40 (9), 2233–2245 (1992).CrossRefGoogle Scholar
13.Pezzotti, G., Kleebe, H-J., and Ota, K., J. Am. Ceram. Soc. (in press).Google Scholar
14.Fujita, S., Maeda, K., and Hyodo, S., Philos. Mag. A 55 (2), 203–215 (1987).CrossRefGoogle Scholar
15.Reimanis, I. E., Suematsu, H., Petrovic, J. J., and Mitchell, T. E., J. Am. Ceram. Soc. 79 (8), 2065–2073 (1996).CrossRefGoogle Scholar
16.Suematsu, H., Petrovic, J. J., and Mitchell, T. E., Mater. Sci. Eng. A A209, 97–102 (1996).CrossRefGoogle Scholar
17.Rosolowski, J. H. and Greskovich, C. D., “Ceramic Sintering,” NTIS-Rept. No. AC/A001-012 (1974).Google Scholar
18.Grskovich, C. D., Rosolowski, J. H., and Prochazka, S., “Ceramic Sintering,” NTIS-Rpt. No. AD/A014-480 (1975).Google Scholar
19.Pezzotti, G. and Ota, K., J. Am. Ceram. Soc. 80 (9), 2205–2212 (1997).CrossRefGoogle Scholar
20.Nowick, A. S. and Berry, B. S., Anelastic Relaxation in Crystalline Solids (Academic Press, New York, 1972).Google Scholar
21.Pezzotti, G., Kleebe, H-J., Ota, K., and Nishida, T., Acta Mater. 45 (10), 4171–4179 (1997).CrossRefGoogle Scholar
22.Findley, W. N., Lai, J. S., and Onaran, K., Creep and Relaxation of Nonlinear Viscoelastic Materials (Dover Publ., Inc., New York, 1976).Google Scholar