No CrossRef data available.
Article contents
Failure Probabilities of Reinforced Concrete Square Pile Caps
Published online by Cambridge University Press: 05 May 2011
Abstract
An analytical model for determining the shear strength of concrete pile caps under the failure mode of diagonal-compression originally based on the softened strut-and-tie model is proposed. The failure probabilities of reinforced concrete pile caps are investigated by Monte Carlo method. The results indicate that the proposed model can accurately predict the shear strength of the pile caps. The distribution of the failure probabilities for pile caps designed to ACI 318-02 Appendix A and the proposed design method are more uniform than that designed to the ACI 318-99. The ACI 318-99 is very conservative and cannot provide a consistent safety for pile caps design. It is suggested that the procedures in the ACI 318-02 Appendix A should be moved to the main body of ACI 318-02 and the proposed design method should be incorporated into the current reinforced concrete pile cap design methods.
- Type
- Technical Note
- Information
- Copyright
- Copyright © The Society of Theoretical and Applied Mechanics, R.O.C. 2007
References
1. ACI Committee 318, “Building Code Requirements for Structural Concrete (ACI 318–99) and Commentary (ACI 318R-99),”American Concrete Institute, Farmington Hills, MI, 391pp. (1999).Google Scholar
2.Adebar, P. and Zhou, Z., “Design of Deep Pile Caps by Strut-and-Tie Models,” ACI StructuralJournal, 93(4), pp. 437–448 (1996).Google Scholar
3. ACI Committee 318, “Building Code Requirements for Structural Concrete (ACI 318–02) and Commentary (ACI 318R-02),”American Concrete Institute, Farmington Hills, MI, 444 pp. (2002).Google Scholar
4.Hwang, S. J. and Lee, H. J., “Strength Prediction for Discontinuity Regions Failing in Diagonal Compressions by Softened Strut-and-tie Model,” Journal of Structural Engineering, ASCE, 128(12), pp. 1519–1526(2002).CrossRefGoogle Scholar
5.Hwang, S. J., Lu, W. Y. and Lee, H. J., “Shear Strength Prediction for Deep Beams,” ACI Structural Journal, 97(3), pp. 367–376 (2000).Google Scholar
6.Clarke, J. L., “Behavior and Design of Pile Caps with Four Piles,” Cement and Concrete Association, London, Report 42.489,19 pp. (1973).Google Scholar
7.Sabins, G. M. and Gogate, A. B., “Investigation of Thick Slab (Pile Cap) Behavior,” ACI Journal, 81(1), pp. 35–39 (1984).Google Scholar
8.Ohtsuki, K. and Suzuki, K., “Experimental Study on Bending Ultimate Strength of Four Pile Caps,” Journal of Structural and Construction Engineering, AIJ, 482, pp. 93–102 (1996) (in Japanese).CrossRefGoogle Scholar
9.Lu, W. Y., “Failure Probabilities of Reinforced Concrete Column Footings,” Journal of the Chinese Institute of Engineers, 29(4), pp. 733–739 (2006).CrossRefGoogle Scholar
10.Nowak, A. S. and Szerszen, M. M., “Calibration of Design Code for Buildings (ACI 318): Part 1- Statistical Models for Resistance,” ACI Structural Journal, 100(3), pp. 377–382 (2003).Google Scholar
11.Diniz, S. M. C. and Frangopol, D. M., “Reliability Bases for High-Strength Concrete Columns,” Journal of Structural Engineering, ASCE, 123(10), pp. 1375–1381 (1997).CrossRefGoogle Scholar
12.Ellingwood, B., Galambos, T. V., MacGregor, J. G. and Cornell, C. A., “Development of Probabilities Based Load Criterion for American National Standard A58,” NBS Special Publication, National Bureau of Standards, Washington, D. C., 577, 222 pp. (1980).CrossRefGoogle Scholar
13.Darwin, D., Idun, E. K., Zuo, J. and Tholen, M. L., “Reliability-based Strength Reduction Factor for Bond,” ACI Structural Journal, 95(4), pp. 434–443 (1998).Google Scholar
14.Lu, W. Y., “A Study on the Safety of the Shear Capacity Design of Reinforced Concrete Beam-Column Joints,” Journal of Mechanics, 22, pp. 271–280 (2006).CrossRefGoogle Scholar