Hostname: page-component-7bb8b95d7b-5mhkq Total loading time: 0 Render date: 2024-09-20T08:34:50.314Z Has data issue: false hasContentIssue false
  • English
  • Français

Germanium Implantation into Silicon: An Alternate Pre-Amorphization/Rapid Thermal Annealing Procedure for Shallow Junction Technology

Published online by Cambridge University Press:  22 February 2011

D.K. Sadana ,
E. Myers ,
J. Liu ,
T. Finstad  and
G.A. Rozgonyi
D.K. Sadana
Affiliation:
Microelectronics Center of North Carolina, Research Triangle Park, NC 27709; North Carolina State University, Raleigh, NC 27650;
E. Myers
Affiliation:
North Carolina State University, Raleigh, NC 27650;
J. Liu
Affiliation:
North Carolina State University, Raleigh, NC 27650;
T. Finstad
Affiliation:
University of North Carolina, Chapel Hill, NC 27514.
G.A. Rozgonyi
Affiliation:
Microelectronics Center of North Carolina, Research Triangle Park, NC 27709; North Carolina State University, Raleigh, NC 27650;
Get access

Abstract

Germanium implantation into Si was conducted to pre-amorphize the-si surface layer prior to a shallow/high dose (42 keV, 2 × 1015 cm−2) BF2 implant. Cross-sectional transmission electron microscopy showed that rapid thermal annealing (RTA) of the amorphous layer (without BF2 ) leaves defect-free material in the implanted region. Only a discrete layer of small (∼300Å) dislocation loops due to straggling ion damage was found to be present at a depth corresponding to the amorphous/crystalline interface. RTA of the amorphous layer with the BF2 creatpd a high density of uniformly. distributed fine defect clusters (∼50Å) in the surface region (0–500Å) in addition to the straggling ion damage. Boron and F profiles obtained by secondary ion mass spectrometry from the unannealed and rapid thermally annealed samples showed the presence of high concentrations of these impurities in the surface region where the fine defect clusters were observed. A comparison of the RTA behavior of the pre-amorphized surface layers (with or without BF2 ) produced by Ge and self-implantation is presented.

Type
Research Article
Information
MRS Online Proceedings Library (OPL) , Volume 23 , 1983 , 303
Copyright
Copyright © Materials Research Society 1984

Access options

Get access to the full version of this content by using one of the access options below. (Log in options will check for institutional or personal access. Content may require purchase if you do not have access.)

References

REFERENCES

1.Sedgwick, T.O., VLSI Science & Tech. Eds: Dell'Oca, C.J. and Bullis, W.M., The Electrochemical Society, Princeton, NJ (1982) pp.130.Google Scholar
2.Hofker, W.K., Philips Res. Dept. Suppl. 8 (1975) PhD Thesis.Google Scholar
3.Sadana, D.K., Shatas, S. and Gat, A., Proc. Inst. Phys. (London) 1983 (in Press).Google Scholar
4.Tsai, M.Y. and Streetman, B.G., J. App. Phys. 50 183 (1979).Google Scholar
5.Maszara, W., Carter, C., Sadana, D.K., Rozgonyi, G.A., Liu, J. and Wortman, J.J. (see this proceeding).Google Scholar
6.Seidel, T.E., Knoell, R., Stevie, F.A., Poli, G. and Schwartz, B. (private communication).Google Scholar
7.Pavlov, P.V., Pashkov, V.I. and Dobrokhotov, E.V., Sov. Phys. Solid State 15 2257 (1974).Google Scholar
8.Sadana, D.K., Fletcher, J. and Booker, G.R., Electronics Lett. (Britain) 15 615 (1977).Google Scholar
9.Sadana, D.K., Maszara, W., Wortman, J.J., Chu, W.K. and Rozgonyi, G.A. (paper submitted to the ECS Journal).Google Scholar