Hostname: page-component-76fb5796d-dfsvx Total loading time: 0 Render date: 2024-04-29T22:56:29.141Z Has data issue: false hasContentIssue false
  • English
  • Français

An investigation of the creep processes in tin and aluminum using a depth-sensing indentation technique

Published online by Cambridge University Press:  31 January 2011

V. Raman  and
R. Berriche
V. Raman
Affiliation:
IBM Storage Systems Products Division, San Jose, California 95193
R. Berriche
Affiliation:
Department of Geology and Geophysics, University of Minnesota, Minneapolis, Minnesota 55455
Get access

Abstract

Constant load creep experiments were conducted using a depth-sensing indentation instrument with indentation depths in the submicron range. Experiments were conducted on polycrystalline Sn and sputtered Al films on Si substrates. The results show that the plastic depth versus time curves and the strain rate versus stress plots from these experiments are analogous to those obtained from conventional creep experiments using bulk specimens. The value of the stress exponent for Sn is close to the reported values from uniaxial creep tests. Tests on Al films showed that the stress exponent is dependent on the indentation depth and is governed by the proximity to the film/substrate interface. Load change experiments were also performed and the data from these tests were analyzed. It is concluded that indentation creep experiments may be useful in elucidating the deformation properties of materials and in identifying deformation mechanisms.

Type
Articles
Information
Journal of Materials Research , Volume 7 , Issue 3 , March 1992 , pp. 627 - 638
Copyright
Copyright © Materials Research Society 1992

Access options

Get access to the full version of this content by using one of the access options below. (Log in options will check for institutional or personal access. Content may require purchase if you do not have access.)

References

1.Korhonen, M.A., LaFontaine, W.R., Paszkiet, C.A., Black, R.D., and Li, Che-Yu, in Thin Films: Stresses and Mechanical Properties II, edited by Doerner, M. F., Oliver, W. C., Pharr, G. M., and Brotzen, F. R. (Mater. Res. Soc. Symp. Proc. 188, Pittsburgh, PA, 1990), p. 159.Google Scholar
2.LaFontaine, W. R., Yost, B., Black, R. D., and Li, Che-Yu, in Thin Films: Stresses and Mechanical Properties II, edited by Doerner, M. F., Oliver, W. C., Pharr, G.M., and Brotzen, F.R. (Mater. Res. Soc. Symp. Proc. 188, Pittsburgh, PA, 1990), p. 165.Google Scholar
3.Oliver, W. C., McHargue, C.J., and Zinkle, S.J., Thin Solid Films 153, 185 (1987).CrossRefGoogle Scholar
4.Stone, D., LaFontaine, W. R., Alexopoulos, P., Wu, T-W., and Li, Che-Yu, J. Mater. Res. 3, 141 (1988).CrossRefGoogle Scholar
5.Wu, T-W., Thin Films: Stresses and Mechanical Properties II, edited by Doerner, M.F., Oliver, W.C., Pharr, G.M., and Brotzen, F.R. (Mater. Res. Soc. Symp. Proc. 188, Pittsburgh, PA, 1990), p. 191.Google Scholar
6.Mayo, M. J., Siegel, R. W., Narayanasamy, A., and Nix, W. D., J. Mater. Res. 5, 1073 (1990).CrossRefGoogle Scholar
7.Chu, S. N. G. and Li, J. C. M., J. Mater. Sci. 12, 2200 (1977).CrossRefGoogle Scholar
8.Chu, S. N. G. and Li, J. C. M., Mater. Sci. and Eng. 45, 167 (1980).CrossRefGoogle Scholar
9.Chu, S. N. G. and Li, J. C. M., Mater. Sci. and Eng. 39, 1 (1979).CrossRefGoogle Scholar
10.Hannula, S-P., Stone, D., and Li, Che-Yu, in Electronic Packaging Materials Science, edited by Giess, E.A., Tu, K-N., and Uhlmann, D. R. (Mater. Res. Soc. Symp. Proc. 40, Pittsburgh, PA, 1985), p. 217.Google Scholar
11.Wu, T.W., Moshref, M., and Alexopoulos, P.S., Thin Solid Films 187, 295 (1990).CrossRefGoogle Scholar
12.LaFontaine, W. R., Yost, B., Black, R. D., and Li, C-Y., J. Mater. Res. 5, 2100 (1990).CrossRefGoogle Scholar
13.Mayo, M. J. and Nix, W. D., Strength of Metals and Alloys, edited by Kettunen, P. O., Lepisto, T. K., and Lehtonen, M. E. (Pergamon, Oxford, 1988), p. 1415.Google Scholar
14.Nix, W. D., Metall. Trans. 20A, 2217 (1989).CrossRefGoogle Scholar
15.Doerner, M.F. and Nix, W.D., J. Mater. Res. 1, 601 (1986).CrossRefGoogle Scholar
16.Pethica, J., Hutchings, R., and Oliver, W. C., Philos. Mag. A 48, 593 (1983).CrossRefGoogle Scholar
17.Ahlquist, C.N. and Nix, W.D., Scripta Metall. 3, 679 (1969).CrossRefGoogle Scholar
18.Horiuchi, R. and Otsuka, M., Trans. Jpn. Inst. Metal. 13, 284 (1972).CrossRefGoogle Scholar
19.Mohammed, F. A., Murty, K. L., and Morris, J. W., Metall. Trans. 4, 935 (1973).CrossRefGoogle Scholar
20.Nix, W.D. and Ilschner, B., Strength of Metals and Alloys, edited by Haasen, P., Gerold, V., and Kostorz, G. (Pergamon Press, Oxford, 1979), Vol. 3, p. 1503.CrossRefGoogle Scholar
21.Hawthorne, H. M. and Sherwood, J. N., Trans. Faraday Soc. 66, 1792 (1970).CrossRefGoogle Scholar
22.Frenkel, R.E., Sherby, O.D., and Dorn, J.E., Acta Metall. 3, 470 (1955).CrossRefGoogle Scholar
23.Langdon, T. G., Metals Forum 1, 59 (1978).Google Scholar
24.Sherby, O. D., Klundt, R. H., and Miller, A. K., Metall. Trans. 8A, 843 (1977).CrossRefGoogle Scholar
25.Raman, V. and Berriche, R., Thin Films: Stresses and Mechanical Properties II, edited by Doerner, M. F., Oliver, W. C., Pharr, G. M., and Brotzen, F. R. (Mater. Res. Soc. Symp. Proc. 188, Pittsburgh, PA, 1990), p. 171.Google Scholar