Until recently, the analysis of polymer laminates using infrared microspectroscopy involved the painstaking separation of individual layers by dissection or by obtaining micrometer thin cross-sections. The latter usually requires the expertise of an individual trained in microtomy and even then, the very structure of the laminate could affect the outcome of the spectral results. The recent development of attenuated total internal reflection (ATR) infrared microspectroscopy imaging has provided a new avenue for the analysis of these multilayer structures. This report compares ATR infrared microspectroscopy imaging with conventional transmission infrared microspectroscopy imaging. The results demonstrate that the ATR method offers improved spatial resolution, eliminates a variety of competing optical processes, and requires minimal sample preparation relative to transmission measurements. These advantages were illustrated using a polymer laminate consisting of 11 different layers whose thickness ranged in size from 4–20 μm. The spatial resolution achieved by using an ATR-FTIR (Fourier transform infrared spectroscopy) imaging technique was diffraction limited. Contrast in the ATR images was enhanced by principal component analysis.

This paper deals with an optimization of a field-emission structure concept based on vertically aligned carbon nanotubes (CNT). A design concept for a fabrication method for a gate structure based on electron beam lithography is reviewed in the first part of the paper. A single carbon nanotube is grown by the PECVD method inside the gate structure. Calculations and simulations that help determine gate structure proportions in order to obtain the best possible electron reduced brightness and to predict the cathode's electric behavior are also essential parts of this study.

The present work reports a simple and easy wet chemistry synthesis of cuprous oxide (Cu2O) nanospheres at room temperature without surfactants and using different precursors. Structural characterization was carried out by X-ray diffraction, transmission electron microscopy, and scanning electron microscopy coupled with focused ion beam and energy-dispersive X-ray spectroscopy. The optical band gaps were determined from diffuse reflectance spectroscopy. The photoluminescence behavior of the as-synthesized nanospheres showed significant differences depending on the precursors used. The Cu2O nanospheres were constituted by aggregates of nanocrystals, in which an on/off emission behavior of each individual nanocrystal was identified during transmission electron microscopy observations. The thermal behavior of the Cu2O nanospheres was investigated with in situ X-ray diffraction and differential scanning calorimetry experiments. Remarkable structural differences were observed for the nanospheres annealed in air, which turned into hollow spherical structures surrounded by outsized nanocrystals.

Several particles of copper accompanied by a few particles of nickel, lead, and a compound composed of selenium containing minor Ni, Si, Cu, and Co were found in human gall, kidney, and bladder stones. The investigated particles occur as tiny grains, <10 µm in size, that are irregularly dispersed in the stones. Therefore, they were studied by scanning electron microscopy and qualitatively analyzed by energy dispersive system. One grain of copper contained a small amount of Ni and Zn, and some grains of nickel proved to contain Cr as trace element. Most of the discovered metals formed a single-phase grain. However, a few grains found in two gallstones were associated with inclusions of calcium and apatite. Based on the results presented in this contribution, we argue that most of the studied metals can be classified as endogenous particles, i.e., directly precipitated from the same fluids that formed their host human stones. This observation suggests that the precipitation and accumulation of metals in some human stones can be considered an efficient way to eliminate them from the human body.

Stereological techniques using the optical disectors require estimation of final section thickness, but frozen tissue irregularities may interfere with this estimation. Cryostat slices from rodent nerve tissues (dorsal root ganglia, spinal cord, and brain), cut at 16, 40, and 50 μm, were digitized with a confocal microscope and visualized through 3D software. Geometric section thickness of tissue (Tgeom) was defined as tissue volume/area. Maximal section thicknesses (Tmax), from the top to the bottom of the section, were measured in a random sample of vertical ZX planes. Irregularities were mostly related to blood vessels traversing the tissue and neuronal somas protruding over the cut surfaces, with other neuron profiles showing a fragmented appearance. Irregularities contributed to increasing the distance between the tops and bottoms of slices sectioned in different laboratories. Significant differences were found between Tmax and Tgeom for all thickness studies and counting frames (p<0.01). The Tgeom/Tmax average rate was 68.4–85.7% in volumes around cell profiles (∼600–1,200 μm2) and 83.3–91.8% in subcellular samples (∼25–160 μm2). Confocal microscopy may help to assess tissue irregularities, which might lead to an overestimation of tissue volume if section thickness is estimated by focusing on the top and bottom of the sections.

We compare experimental fluctuation electron microscopy (FEM) speckle data with electron diffraction simulations for thin amorphous carbon and silicon samples. We find that the experimental speckle intensity variance is generally more than an order of magnitude lower than kinematical scattering theory predicts for spatially coherent illumination.

We hypothesize that decoherence, which randomizes the phase relationship between scattered waves, is responsible for the anomaly. Specifically, displacement decoherence can contribute strongly to speckle suppression, particularly at higher beam energies. Displacement decoherence arises when the local structure is rearranged significantly by interactions with the beam during the exposure. Such motions cause diffraction speckle to twinkle, some of it at observable time scales.

We also find that the continuous random network model of amorphous silicon can explain the experimental variance data if displacement decoherence and multiple scattering is included in the modeling. This may resolve the longstanding discrepancy between X-ray and electron diffraction studies of radial distribution functions, and conclusions reached from previous FEM studies.

Decoherence likely affects all quantitative electron imaging and diffraction studies. It likely contributes to the so-called Stobbs factor, where high-resolution atomic-column image intensities are anomalously lower than predicted by a similar factor to that observed here.

Intraluminal contents of benign and malignant prostatic tissue are associated with varying forms of acellular structures. These include corpora amylacea, prostatic calculi, and prostatic crystalloids. There are relatively few microscopy studies about the characterization of intraluminal structures from benign and malignant prostatic glands and little is known about their chemical composition. In the present study, we used a combination of special histochemical methods, immunohistochemistry, and transmission electron microscopy to characterize intraluminal contents of benign and malignant prostate glands. The study was done on 33 radical prostatectomy and four transurethral resections of prostate specimens. Histochemical methods such as von Kossa, autometallography (AMG), as well as PSA immunohistochemistry and transmission electron microscopy were performed to characterize intraluminal contents of benign and malignant prostate glands. Von Kossa staining was observed in acellular structures, corpora amylacea, prostatic calculi, and calcified blood vessels. AMG staining was observed in the lumen of small glands, in the epithelium lining prostate glands, and corpora amylacea. PSA staining showed prostatic glands with both positive and negative corpora amylacea and epithelial cells. Ultrastructural observation revealed the presence of a variety of highly heterogeneous aggregates composed of fibrillar elements that were similar to those of amyloid.

Diluvian Clustering is an unsupervised grid-based clustering algorithm well suited to interpreting large sets of noisy compositional data. The algorithm is notable for its ability to identify clusters that are either compact or diffuse and clusters that have either a large number or a small number of members. Diluvian Clustering is fundamentally different from most algorithms previously applied to cluster compositional data in that its implementation does not depend upon a metric. The algorithm reduces in two-dimensions to a case for which there is an intuitive, real-world parallel. Furthermore, the algorithm has few tunable parameters and these parameters have intuitive interpretations. By eliminating the dependence on an explicit metric, it is possible to derive reasonable clusters with disparate variances like those in real-world compositional data sets. The algorithm is computationally efficient. While the worst case scales as O(N2) most cases are closer to O(N) where N is the number of discrete data points. On a mid-range 2014 vintage computer, a typical 20,000 particle, 30 element data set can be clustered in a fraction of a second.

Microstructural features of nanostructured copper-matrix composites produced via high-energy milling were studied. Copper–graphite–alumina batches were planetary ball milled up to 16 h; copper–graphite batches were also prepared under the same conditions to evaluate the effect of contamination from the milling media. The microstructure of the produced materials was characterized by field emission gun scanning electron microscopy/energy-dispersive spectroscopy and related to Raman, X-ray diffraction, and particle size analysis results. Results showed that alumina was present in all milled powders. However, size reduction was effective at shorter times in the copper–graphite–alumina system. In both cases the produced powders were nanostructured, containing graphite and alumina nanoparticles homogeneously distributed in the copper matrix, especially for longer milling times and in the presence of added alumina. Copper crystallite size was significantly affected above 4 h milling; nanographite size decreased and incipient amorphization occurred. A minimum size of 15 nm was obtained for the copper crystallite copper–alumina–graphite composite powders, corresponding to 16 h of milling. Contamination from the media became more significant above 8 h. Results suggest that efficient dispersion and bonding of graphite and alumina nanoparticles in the copper matrix is achieved, envisioning high conductivity, high strength, and thermal stability.

Although the advent of microwave technologies has both improved and accelerated tissue processing for microscopy, there still remain many limitations in conventional chemical fixation, dehydration, embedding, and sectioning, particularly with regard to plant materials. The Proteaceae, a family of plants widely distributed in the Southern Hemisphere and well adapted to harsh climates and nutrient-poor soils, is a perfect example; the complexity of Proteaceae leaves means that almost no ultrastructural data are available as these are notoriously difficult to both infiltrate and section. Here, a step-by-step protocol is described that allows for the successful preparation of Banksia prionotes (Australian Proteaceae) leaves for both light and transmission electron microscopy. The method, which applies a novel combination of vibratome sectioning, microwave processing and vacuum steps, and the utilization of an ultra low viscosity resin, results in highly reproducible, well-preserved, sectionable material from which very high-quality light and electron micrographs can be obtained. With this, cellular ultrastructure from the level of a leaf through to organelle substructure can be studied. This approach will be widely applicable, both within and outside of the plant sciences, and can be readily adapted to meet specific sample requirements and imaging needs.

By transmission electron microscopy with extended Burgers vector analyses, we demonstrate the edge and screw character of vertical dislocations (VDs) in novel SiGe heterostructures. The investigated pillar-shaped Ge epilayers on prepatterned Si(001) substrates are an attempt to avoid the high defect densities of lattice mismatched heteroepitaxy. The Ge pillars are almost completely strain-relaxed and essentially defect-free, except for the rather unexpected VDs. We investigated both pillar-shaped and unstructured Ge epilayers grown either by molecular beam epitaxy or by chemical vapor deposition to derive a general picture of the underlying dislocation mechanisms. For the Burgers vector analysis we used a combination of dark field imaging and large-angle convergent beam electron diffraction (LACBED). With LACBED simulations we identify ideally suited zeroth and second order Laue zone Bragg lines for an unambiguous determination of the three-dimensional Burgers vectors. By analyzing dislocation reactions we confirm the origin of the observed types of VDs, which can be efficiently distinguished by LACBED. The screw type VDs are formed by a reaction of perfect 60° dislocations, whereas the edge types are sessile dislocations that can be formed by cross-slips and climbing processes. The understanding of these origins allows us to suggest strategies to avoid VDs.