12 results
Global dynamics and topology of two-phase mixing layer flow through simultaneous gas and liquid velocity measurements
- Alessandro Della Pia, Theodoros Michelis, Matteo Chiatto, Marios Kotsonis, Luigi de Luca
-
- Journal:
- Journal of Fluid Mechanics / Volume 981 / 25 February 2024
- Published online by Cambridge University Press:
- 19 February 2024, A13
-
- Article
- Export citation
-
This study reports the first time-resolved particle image velocimetry characterization of a planar two-phase mixing layer flow, whose velocity field is measured simultaneously in gas and liquid streams. Two parallel air and water flows meet downstream of a splitter plate, giving rise to an initially spanwise invariant configuration. The aim is to elucidate further the mechanisms leading to the flow breakup in gas-assisted atomization. The complete experimental characterization of the velocity field represents a database that could be used in data-driven reduced-order models to investigate the global behaviour of the flow system. After the analysis of a selected reference case, a parametric study of the flow behaviour is performed by varying the liquid ($Re_l$) and gas ($Re_g$) Reynolds numbers, and as a consequence also the gas-to-liquid dynamic pressure ratio ($M$), shedding light on both time-averaged (mean) and unsteady velocity fields. In the reference case, it is shown that the mean flow exhibits a wake region just downstream of the splitter plate, followed by the development of a mixing layer. By increasing both $Re_l$ and $Re_g$, the streamwise extent of the wake decreases and eventually vanishes, the flow resulting in a pure mixing layer regime. The spectral analysis of the normal-to-flow velocity fluctuations outlines different flow regimes by variation of the governing parameters, giving more insights into the global characteristics of the flow field. As a major result, it is found that at high $Re_g$ and $M$ values, the velocity fluctuations are characterized by low-frequency temporal oscillations synchronized in several locations within the flow field, which suggest the presence of a global mode of instability. The proper orthogonal decomposition of velocity fluctuations, performed in both gas and liquid phases, reveals finally that the synchronized oscillations are associated with a low-frequency dominant flapping mode of the gas–liquid interface. Higher-order modes correspond to interfacial wave structures travelling with the so-called Dimotakis velocity. For lower gas Reynolds numbers, the leading modes describe higher frequency fingers shedding at the interface.
Unsteady interaction of crossflow instability with a forward-facing step
- Alberto F. Rius-Vidales, Marios Kotsonis
-
- Journal:
- Journal of Fluid Mechanics / Volume 939 / 25 May 2022
- Published online by Cambridge University Press:
- 30 March 2022, A19
-
- Article
-
- You have access Access
- Open access
- HTML
- Export citation
-
Experiments have been conducted on a swept wing model in a low-turbulence wind tunnel at chord Reynolds number of $2.17 \times 10^{6}$ to investigate the unsteady interaction of a forward-facing step (FFS) with incoming stationary crossflow (CF) vortices. The impact of varying the FFS height on the development and growth of primary and secondary CF disturbances and the ensuing laminar–turbulent transition is quantified through detailed hot-wire anemometry and infrared thermography measurements. The presence of the FFS results in either a critical (i.e. moderate transition advancement) or a supercritical behaviour (i.e. transition advancing abruptly to the FFS location). The arrival of the forced stationary CF vortices at the step is accompanied by their amplification. Unsteady analysis for the critical cases indicates temporal velocity fluctuations following closely the development of the baseline configuration (i.e. agreeing with the development of secondary instabilities). Consequently, laminar breakdown originates from the outer side of the upwelling region of the CF vortices. In contrast, for the supercritical FFS, the laminar breakdown unexpectedly originates from the inner side of the upwelling region. Evidence points to an unsteady mechanism possibly supported by locally enhanced spanwise-modulated shears and the recirculation region downstream of the FFS edge. This mechanism appears to govern the abrupt tripping of the flow in supercritical step cases. The findings in this work provide insight into the unsteady FFS–CF vortex interaction, which is pivotal to understanding the influence of an FFS on the laminar–turbulent boundary-layer transition in swept aerodynamic surfaces.
Effect of velocity ratio on the interaction between plasma synthetic jets and turbulent cross-flow
- Haohua Zong, Marios Kotsonis
-
- Journal:
- Journal of Fluid Mechanics / Volume 865 / 25 April 2019
- Published online by Cambridge University Press:
- 28 February 2019, pp. 928-962
-
- Article
- Export citation
-
Plasma synthetic jet actuators (PSJAs) are particularly suited for high-Reynolds-number, high-speed flow control due to their unique capability of generating supersonic pulsed jets at high frequency (${>}5$ kHz). Different from conventional synthetic jets driven by oscillating piezoelectric diaphragms, the exit-velocity variation of plasma synthetic jets (PSJs) within one period is significantly asymmetric, with ingestion being relatively weaker (less than $20~\text{m}~\text{s}^{-1}$) and longer than ejection. In this study, high-speed phase-locked particle image velocimetry is employed to investigate the interaction between PSJAs (round exit orifice, diameter 2 mm) and a turbulent boundary layer at constant Strouhal number (0.02) and increasing mean velocity ratio ($r$, defined as the ratio of the time-mean velocity over the ejection phase to the free-stream velocity). Two distinct operational regimes are identified for all the tested cases, separated by a transition velocity ratio, lying between $r=0.7$ and $r=1.0$. At large velocity and stroke ratios (first regime, representative case $r=1.6$), vortex rings are followed by a trailing jet column and tilt downstream initially. This downstream tilting is transformed into upstream tilting after the pinch-off of the trailing jet column. The moment of this transformation relative to the discharge advances with decreasing velocity ratio. Shear-layer vortices (SVs) and a hanging vortex pair (HVP) are identified in the windward and leeward sides of the jet body, respectively. The HVP is initially erect and evolves into an inclined primary counter-rotating vortex pair ($p$-CVP) which branches from the middle of the front vortex ring and extends to the near-wall region. The two legs of the $p$-CVP are bridged by SVs, and a secondary counter-rotating vortex pair ($s$-CVP) is induced underneath these two legs. At low velocity and stroke ratios (second regime, representative case $r=0.7$), the trailing jet column and $p$-CVP are absent. Vortex rings always tilt upstream, and the pitching angle increases monotonically with time. An $s$-CVP in the near-wall region is induced directly by the two longitudinal edges of the ring. Inspection of spanwise planes ($yz$-plane) reveals that boundary-layer energization is realized by the downwash effect of either vortex rings or $p$-CVP. In addition, in the streamwise symmetry plane, the increasing wall shear stress is attributed to the removal of low-energy flow by ingestion. The downwash effect of the $s$-CVP does not benefit boundary-layer energization, as the flow swept to the wall is of low energy.
Transition in a separation bubble under tonal and broadband acoustic excitation
- John William Kurelek, Marios Kotsonis, Serhiy Yarusevych
-
- Journal:
- Journal of Fluid Mechanics / Volume 853 / 25 October 2018
- Published online by Cambridge University Press:
- 16 August 2018, pp. 1-36
-
- Article
-
- You have access Access
- Open access
- HTML
- Export citation
-
Transition and flow development in a separation bubble formed on an airfoil are studied experimentally. The effects of tonal and broadband acoustic excitation are considered since such acoustic emissions commonly result from airfoil self-noise and can influence flow development via a feedback loop. This interdependence is decoupled, and the problem is studied in a controlled manner through the use of an external acoustic source. The flow field is assessed using time-resolved, two-component particle image velocimetry, the results of which show that, for equivalent energy input levels, tonal and broadband excitation can produce equivalent changes in the mean separation bubble topology. These changes in topology result from the influence of excitation on transition and the subsequent development of coherent structures in the bubble. Both tonal and broadband excitation lead to earlier shear layer roll-up and thus reduce the bubble size and advance mean reattachment upstream, while the shed vortices tend to persist farther downstream of mean reattachment in the case of tonal excitation. Through a cross-examination of linear stability theory (LST) predictions and measured disturbance characteristics, nonlinear disturbance interactions are shown to play a crucial role in the transition process, leading to significantly different disturbance development for the tonal and broadband excited flows. Specifically, tonal excitation results in transition being dominated by the excited mode, which grows in strong accordance with linear theory and damps the growth of all other disturbances. On the other hand, disturbance amplitudes are more moderate for the natural and broadband excited flows, and so all unstable disturbances initially grow in accordance with LST. For all cases, a rapid redistribution of perturbation energy to a broad range of frequencies follows, with the phenomenon occurring earliest for the broadband excitation case. By taking nonlinear effects into consideration, important ramifications are made clear in regards to comparing LST predictions and experimental or numerical results, thus explaining the trends reported in recent investigations. These findings offer new insights into the influence of tonal and broadband noise emissions, resulting from airfoil self-noise or otherwise, on transition and flow development within a separation bubble.
Secondary crossflow instability through global analysis of measured base flows
- Koen J. Groot, Jacopo Serpieri, Fabio Pinna, Marios Kotsonis
-
- Journal:
- Journal of Fluid Mechanics / Volume 846 / 10 July 2018
- Published online by Cambridge University Press:
- 09 May 2018, pp. 605-653
-
- Article
-
- You have access Access
- Open access
- HTML
- Export citation
-
A combined experimental and numerical approach to the analysis of the secondary stability of realistic swept-wing boundary layers is presented. Global linear stability theory is applied to experimentally measured base flows. These base flows are three-dimensional laminar boundary layers subject to spanwise distortion due to the presence of primary stationary crossflow vortices. A full three-dimensional description of these flows is accessed through the use of tomographic particle image velocimetry (PIV). The stability analysis solves for the secondary high-frequency modes of type I and type II, ultimately responsible for turbulent breakdown. Several pertinent parameters arising from the application of the proposed methodology are investigated, including the mean flow ensemble size and the measurement domain extent. Extensive use is made of the decomposition of the eigensolutions into the terms of the Reynolds–Orr equation, allowing insight into the production and/or destruction of perturbations from various base flow features. Stability results demonstrate satisfactory convergence with respect to the mean flow ensemble size and are independent of the handling of the exterior of the measurement domain. The Reynolds–Orr analysis reveals a close relationship between the type I and type II instability modes with spanwise and wall-normal gradients of the base flow, respectively. The structural role of the in-plane velocity components in the perturbation growth, topology and sensitivity is identified. Using the developed framework, further insight is gained into the linear growth mechanisms and later stages of transition via the primary and secondary crossflow instabilities. Furthermore, the proposed methodology enables the extension and enhancement of the experimental measurement data to the pertinent instability eigenmodes. The present work is the first demonstration of the use of a measured base flow for stability analysis applied to the swept-wing boundary layer, directly avoiding the modelling of the primary vortices receptivity processes.
Experimental control of swept-wing transition through base-flow modification by plasma actuators
- Srikar Yadala, Marc T. Hehner, Jacopo Serpieri, Nicolas Benard, Philipp C. Dörr, Markus J. Kloker, Marios Kotsonis
-
- Journal:
- Journal of Fluid Mechanics / Volume 844 / 10 June 2018
- Published online by Cambridge University Press:
- 13 April 2018, R2
-
- Article
-
- You have access Access
- Open access
- HTML
- Export citation
-
Control of laminar-to-turbulent transition on a swept-wing is achieved by base-flow modification in an experimental framework, up to a chord Reynolds number of 2.5 million. This technique is based on the control strategy used in the numerical simulation by Dörr & Kloker (J. Phys. D: Appl. Phys., vol. 48, 2015b, 285205). A spanwise uniform body force is introduced using dielectric barrier discharge plasma actuators, to either force against or along the local cross-flow component of the boundary layer. The effect of forcing on the stability of the boundary layer is analysed using a simplified model proposed by Serpieri et al. (J. Fluid Mech., vol. 833, 2017, pp. 164–205). A minimal thickness plasma actuator is fabricated using spray-on techniques and positioned near the leading edge of the swept-wing, while infrared thermography is used to detect and quantify transition location. Results from both the simplified model and experiment indicate that forcing along the local cross-flow component promotes transition while forcing against successfully delays transition. This is the first experimental demonstration of swept-wing transition delay via base-flow modification using plasma actuators.
On the origin of spanwise vortex deformations in laminar separation bubbles
- Theodoros Michelis, Serhiy Yarusevych, Marios Kotsonis
-
- Journal:
- Journal of Fluid Mechanics / Volume 841 / 25 April 2018
- Published online by Cambridge University Press:
- 19 February 2018, pp. 81-108
-
- Article
-
- You have access Access
- Open access
- HTML
- Export citation
-
This work investigates the three-dimensional, spatio-temporal flow development in the aft portion of a laminar separation bubble. The bubble is forming on a flat plate geometry, subjected to an adverse pressure gradient, featuring maximum reverse flow of approximately 2 % of the local free-stream velocity. Time-resolved velocity measurements are performed by means of planar and tomographic particle image velocimetry, in the vicinity of the reattachment region. The measurements are complemented with a numerical solution of the boundary layer equations in the upstream field. The combined numerical and measured boundary layer is used as a baseline flow for linear stability theory analysis. The results provide insight into the dynamics of dominant coherent structures that form in the separated shear layer and deform along the span. Stability analysis shows that the flow becomes unstable upstream of separation, where both normal and oblique modes undergo amplification. While the shear layer roll up is linked to the amplification of the fundamental normal mode, the oblique modes at angles lower than approximately $30^{\circ }$ are also amplified substantially at the fundamental frequency. A model based on the stability analysis and experimental measurements is employed to demonstrate that the spanwise deformations of rollers are produced due to a superposition of normal and oblique instability modes initiating upstream of separation. The degree of the initial spanwise deformations is shown to depend on the relative amplitude of the dominant normal and oblique waves. This is confirmed by forcing the normal mode through a controlled impulsive perturbation introduced by a spanwise invariant dielectric-barrier-discharge plasma actuator, resulting in the formation of spanwise coherent vortices. The findings elucidate the link between important features in the bubble shedding dynamics and stability characteristics and provide further clarification on the differences in the development of coherent structures seen in recent experiments. Moreover, the results present a handle on the development of effective control strategies that can be used to either promote or suppress shedding in separation bubbles, which is of interest for system performance improvement and control of aeroacoustic emissions in relevant applications.
Formation, evolution and scaling of plasma synthetic jets
- Haohua Zong, Marios Kotsonis
-
- Journal:
- Journal of Fluid Mechanics / Volume 837 / 25 February 2018
- Published online by Cambridge University Press:
- 20 December 2017, pp. 147-181
-
- Article
- Export citation
-
Plasma synthetic jet actuators (PSJAs), capable of producing high-velocity pulsed jets at high frequency, are well suited for high-Reynolds-number subsonic and supersonic flow control. The effects of energy deposition and actuation frequency on the formation and evolution characteristics of plasma synthetic jets (PSJs) are investigated in detail by high-speed phase-locked particle imaging velocimetry (PIV). Increasing jet intensity with energy deposition is mainly contributed by the increasing peak jet velocity ($U_{p}$), while decreasing jet intensity with actuation frequency is attributed to both the reduced cavity density (primary factor) and the shortened jet duration (secondary factor). The total energy efficiency of the considered PSJA ($O(0.01\,\%)$) reduces monotonically with increasing frequency, while the time-averaged thrust produced by the PSJA is positively proportional to both the deposition energy and the frequency. A simplified theoretical model is derived and reveals a scaling power law between the peak jet velocity and the non-dimensional deposition energy (exponent $1/3$). The propagation velocity of the vortex ring attached at the jet front shows a non-monotonic behaviour of initial sharp increase and subsequent mild decay. The peak values for both the propagation velocity and the circulation of the front vortex ring are reached approximately two exit diameters away from the exit. Finally, analysis of the time-averaged flow fields of the issuing PSJ indicates that the axial decay rate of the centreline velocity is proportional to the actuation frequency whereas it is invariant with the energy deposition. The jet spreading rate of the PSJ is found to be higher than steady jets but lower than piezoelectric synthetic jets. Similarly, the entrainment coefficients of the PSJ are found to be twice as high as the values for comparable steady jets.
Conditioning of cross-flow instability modes using dielectric barrier discharge plasma actuators
- Jacopo Serpieri, Srikar Yadala Venkata, Marios Kotsonis
-
- Journal:
- Journal of Fluid Mechanics / Volume 833 / 25 December 2017
- Published online by Cambridge University Press:
- 02 November 2017, pp. 164-205
-
- Article
- Export citation
-
In the current study, selective forcing of cross-flow instability modes evolving on a $45^{\circ }$ swept wing at $Re=2.17\times 10^{6}$ is achieved by means of spanwise-modulated plasma actuators, positioned near the leading edge. In the perspective of laminar flow control, the followed methodology holds on the discrete roughness elements/upstream flow deformation (DRE/UFD) approach, thoroughly investigated by e.g. Saric et al. (AIAA Paper 1998-781, 1998), Malik et al. (J. Fluid Mech., vol. 399, 1999, pp. 85–115) and Wassermann & Kloker (J. Fluid Mech., vol. 456, 2002, pp. 49–84). The possibility of using active devices for UFD provides several advantages over passive means, allowing for a wider range of operating $Re$ numbers and pressure distributions. In the present work, customised alternating current dielectric barrier discharge plasma actuators have been designed, manufactured and characterised. The authority of the actuators in forcing monochromatic stationary cross-flow modes at different spanwise wavelengths is assessed by means of infrared thermography. Moreover, quantitative spatio-temporal measurements of the boundary layer velocity field are performed using time-resolved particle image velocimetry. The results reveal distinct steady and unsteady forcing contributions of the plasma actuator on the boundary layer. It is shown that the actuators introduce unsteady fluctuations in the boundary layer, amplifying at frequencies significantly lower than the actuation frequency. In line with the DRE/UFD strategy, forcing a sub-critical stationary mode, with a shorter wavelength compared to the naturally selected mode, results in less amplified primary vortices and related fluctuations, compared to the critical forcing case. The effect of the forcing on the flow stability is further inspected by combining the measured actuators body force with the numerical solution of the laminar boundary layer and linear stability theory. The simplified methodology yields fast and computationally cheap estimates on the effect of steady forcing (magnitude and direction) on the boundary layer stability.
Response of a laminar separation bubble to impulsive forcing
- Theodoros Michelis, Serhiy Yarusevych, Marios Kotsonis
-
- Journal:
- Journal of Fluid Mechanics / Volume 820 / 10 June 2017
- Published online by Cambridge University Press:
- 12 May 2017, pp. 633-666
-
- Article
- Export citation
-
The spatial and temporal response characteristics of a laminar separation bubble to impulsive forcing are investigated by means of time-resolved particle image velocimetry and linear stability theory. A two-dimensional impulsive disturbance is introduced with an alternating current dielectric barrier discharge plasma actuator, exciting pertinent instability modes and ensuring flow development under environmental disturbances. Phase-averaged velocity measurements are employed to analyse the effect of imposed disturbances at different amplitudes on the laminar separation bubble. The impulsive disturbance develops into a wave packet that causes rapid shrinkage of the bubble in both upstream and downstream directions. This is followed by bubble bursting, during which the bubble elongates significantly, while vortex shedding in the aft part ceases. Duration of recovery of the bubble to its unforced state is independent of the forcing amplitude. Quasi-steady linear stability analysis is performed at each individual phase, demonstrating reduction of growth rate and frequency of the most unstable modes with increasing forcing amplitude. Throughout the recovery, amplification rates are directly proportional to the shape factor. This indicates that bursting and flapping mechanisms are driven by altered stability characteristics due to variations in incoming disturbances. The emerging wave packet is characterised in terms of frequency, convective speed and growth rate, with remarkable agreement between linear stability theory predictions and measurements. The wave packet assumes a frequency close to the natural shedding frequency, while its convective speed remains invariant for all forcing amplitudes. The stability of the flow changes only when disturbances interact with the shear layer breakdown and reattachment processes, supporting the notion of a closed feedback loop. The results of this study shed light on the response of laminar separation bubbles to impulsive forcing, providing insight into the attendant changes of flow dynamics and the underlying stability mechanisms.
Steady and transient response of a laminar separation bubble to controlled disturbances
- Serhiy Yarusevych, Marios Kotsonis
-
- Journal:
- Journal of Fluid Mechanics / Volume 813 / 25 February 2017
- Published online by Cambridge University Press:
- 26 January 2017, pp. 955-990
-
- Article
- Export citation
-
The steady and transient response of a laminar separation bubble to flow disturbances is examined experimentally. Wind tunnel experiments are performed on a NACA 0012 aerofoil at a chord Reynolds number of 130 000 and angle of attack of $2^{\circ }$. Under the investigated conditions, a laminar separation bubble forms on the suction side of the aerofoil in the unperturbed flow. Periodic disturbances are introduced into the boundary layer just upstream of separation by means of a surface-mounted dielectric barrier discharge plasma actuator. Two-component, time-resolved particle image velocimetry measurements are performed to characterise both quasi-steady and transient response of the flow to periodic disturbances. The results show that the dynamics of the laminar separation bubble is dominated by the periodic shedding of shear layer vortices, forming upstream of the mean reattachment location due to the amplification of unstable flow disturbances. Introducing the controlled perturbations leads to significant changes in separation bubble topology and the characteristics of the dominant coherent structures, with the effect dependent on both amplitude and frequency of disturbances. Linear stability analysis demonstrates that the induced changes to the mean bubble topology affect the stability characteristics, reducing the maximum growth rate and the frequency of the most amplified disturbances by 35 % and 20 %, respectively, when the bubble length is reduced by up to 40 %. The observed changes in stability characteristics are shown to correlate with the attendant variations in the shape factor. The transient response of the bubble is associated with significant changes in the separation bubble dynamics, with significant differences observed between the relative duration (${\approx}45\,\%$) of the transients flow response associated with the introduction and removal of the controlled disturbances. A detailed analysis of the results offers new insight into the response of laminar separation bubbles to changes in the disturbance environment.
Three-dimensional organisation of primary and secondary crossflow instability
- Jacopo Serpieri, Marios Kotsonis
-
- Journal:
- Journal of Fluid Mechanics / Volume 799 / 25 July 2016
- Published online by Cambridge University Press:
- 21 June 2016, pp. 200-245
-
- Article
- Export citation
-
An experimental investigation of primary and secondary crossflow instability developing in the boundary layer of a $45^{\circ }$ swept wing at a chord Reynolds number of $2.17\times 10^{6}$ is presented. Linear stability theory is applied for preliminary estimation of the flow stability while surface flow visualisation using fluorescent oil is employed to inspect the topological features of the transition region. Hot-wire anemometry is extensively used for the investigation of the developing boundary layer and identification of the statistical and spectral characteristics of the instability modes. Primary stationary, as well as unsteady type-I (z-mode), type-II (y-mode) and type-III modes are detected and quantified. Finally, three-component, three-dimensional measurements of the transitional boundary layer are performed using tomographic particle image velocimetry. This research presents the first application of an optical experimental technique for this type of flow. Among the optical techniques, tomographic velocimetry represents, to date, the most advanced approach allowing the investigation of spatially correlated flow structures in three-dimensional fields. Proper orthogonal decomposition (POD) analysis of the captured flow fields is applied to this goal. The first POD mode features a newly reported structure related to low-frequency oscillatory motion of the stationary vortices along the spanwise direction. The cause of this phenomenon is only conjectured. Its effect on transition is considered negligible but, given the related high energy level, it needs to be accounted for in experimental investigations. Secondary instability mechanisms are captured as well. The type-III mode corresponds to low-frequency primary travelling crossflow waves interacting with the stationary ones. It appears in the inner upwelling region of the stationary crossflow vortices and is characterised by elongated structures approximately aligned with the axis of the stationary waves. The type-I secondary instability consists instead of significantly inclined structures located at the outer upwelling region of the stationary vortices. The much narrower wavelength and higher advection velocity of these structures correlate with the higher-frequency content of this mode. The results of the investigation of both primary and secondary instability from the exploited techniques agree with and complement each other and are in line with existing literature. Finally, they present the first experimental observation of the secondary instability structures under natural flow conditions.