In this paper, a novel polarization conversion metasurface (PCM) is proposed. Compared with the conventional receiver-transmitter metasurface units, two metallized via holes are set up to correct the current. It can achieve better polarization conversion from linear to circular and maintain a high reflectivity performance. A patch antenna with an L-probe feed is used as a feeder. The circularly polarized Fabry–Perot resonator antenna (CP-FPRA) consists of the PCM with a 5 × 5 array and a feeder. The measurements indicate a 3 dB axial ratio (AR) bandwidth of 8.6% (22.3–24.3 GHz). And it achieves a maximum gain of 14.2 dBic at 24 GHz, compared to the feed antenna has a gain enhancement of 5.5 dBi (from 8.7 dBi to 14.2 dBic). The proposed CP-FPRA has high gain, a wide AR, and a relatively low profile, providing ideas for subsequent antenna designs.

A high-energy pulsed vacuum ultraviolet (VUV) solid-state laser at 177 nm with high peak power by the sixth harmonic of a neodymium-doped yttrium aluminum garnet (Nd:YAG) amplifier in a KBe2BO3F2 prism-coupled device was demonstrated. The ultraviolet (UV) pump laser is a 352 ps pulsed, spatial top-hat super-Gaussian beam at 355 nm. A high energy of a 7.12 mJ VUV laser at 177 nm is obtained with a pulse width of 255 ps, indicating a peak power of 28 MW, and the conversion efficiency is 9.42% from 355 to 177 nm. The measured results fitted well with the theoretical prediction. It is the highest pulse energy and highest peak power ever reported in the VUV range for any solid-state lasers. The high-energy, high-peak-power, and high-spatial-uniformity VUV laser is of great interest for ultra-fine machining and particle-size measurements using UV in-line Fraunhofer holography diagnostics.

EXOSC10 is an exosome-associated ribonuclease that degrades and processes a wide range of transcripts in the nucleus. The initial segment (IS) of the epididymis is crucial for sperm transport and maturation in mice by affecting the absorption and secretion that is required for male fertility. However, the role of EXOSC10 ribonuclease-mediated RNA metabolism within the IS in the regulation of gene expression and sperm maturation remains unknown. Herein, we established an Exosc10 conditional knockout (Exosc10 cKO) mouse model by crossing Exosc10F/F mice with Lcn9-Cre mice which expressed recombinase in the principal cells of IS as early as post-natal day 17. Morphological and histological analyses revealed that Exosc10 cKO males had normal spermatogenesis and development of IS. Moreover, the sperm concentration, morphology, motility, and frequency of acrosome reactions in the cauda epididymides of Exosc10 cKO mice were comparable with those of control mice. Thus, Exosc10 cKO males had normal fertility. Collectively, our genetic mouse model and findings demonstrate that loss of EXOSC10 in the IS of epididymis is dispensable for sperm maturation and male fertility.

The flexible flat cable (FFC) assembly task is a prime challenge in electronic manufacturing. Its characteristics of being prone to deformation under external force, tiny assembly tolerance, and fragility impede the application of robotic assembly in this field. To achieve reliable and stable robotic automation assembly of FFC, an efficient assembly skill acquisition strategy is presented by combining a parallel robot skill learning algorithm with adaptive impedance control. The parallel robot skill learning algorithm is proposed to enhance the efficiency of FFC assembly skill acquisition, which reduces the risk of damaging FFC and tackles the uncertain influence resulting from deformation during the assembly process. Moreover, FFC assembly is also a complex contact-rich manipulation task. An adaptive impedance controller is designed to implement force tracking during the assembly process without precise environment information, and the stability is also analyzed based on the Lyapunov function. Experiments of FFC assembly are conducted to illustrate the efficiency of the proposed method. The experimental results demonstrate that the proposed method is robust and efficient.

This paper retrospectively analysed the prevalence of macrolide-resistant Mycoplasma pneumoniae (MRMP) in some parts of China. Between January 2013 and December 2019, we collected 4,145 respiratory samples, including pharyngeal swabs and alveolar lavage fluid. The highest PCR-positive rate of M. pneumoniae was 74.5% in Beijing, the highest resistance rate was 100% in Shanghai, and Gansu was the lowest with 20%. The highest PCR-positive rate of M. pneumoniae was 74.5% in 2013, and the highest MRMP was 97.4% in 2019; the PCR-positive rate of M. pneumoniae for adults in Beijing was 17.9% and the MRMP was 10.48%. Among the children diagnosed with community-acquired pneumonia (CAP), the PCR-positive and macrolide-resistant rates of M. pneumoniae were both higher in the severe ones. A2063G in domain V of 23S rRNA was the major macrolide-resistant mutation, accounting for more than 90%. The MIC values of all MRMP to erythromycin and azithromycin were ≥ 64 μg/ml, and the MICs of tetracycline and levofloxacin were ≤ 0.5 μg/ml and ≤ 1 μg/ml, respectively. The macrolide resistance varied in different regions and years. Among inpatients, the macrolide-resistant rate was higher in severe pneumonia. A2063G was the common mutation, and we found no resistance to tetracycline and levofloxacin.

Supercritical carbon dioxide (scCO2) processing has been proven as a method for preparing polymer/montmorillonite (MMT) nanocomposites with improved platelet dispersion. The influence of scCO2 processing on the shape and size of the MMT tactoid/platelet, which is of great importance to the final platelet dispersion in the polymer matrix, is scarcely reported in the literature. In the present study, the pristine MMT was first surface modified with 3-glycidoxypropyltrimethoxysilane (the grafted MMT is labeled as GMMT), and then intercalated using three kinds of intercalating agents, myristyltrimethyl-ammonium bromide (MTAB), tetradecyltrihexylphosphonium chloride (TDTHP), and ethoxyltriphenyl-phosphonium chloride (ETPC), in water or scCO2, to study the effect of intercalating agent type and intercalation method on the morphology and thermal properties of GMMT, as a part of a program devoted to the synthesis of polymer/MMT nanocomposites. The structure of intercalated GMMT was characterized by thermogravimetric analysis, X-ray powder diffraction, and scanning electron microscopy (SEM). The optimum intercalation conditions in scCO2 were established by trying a range of reaction times and pressures. The structures of intercalated GMMT obtained under optimum scCO2 conditions and water were compared. The basal spacing of GMMT intercalated in scCO2 was almost the same as that in water, and both were obviously larger than that of GMMT. The GMMT exhibited a compact spherical morphology (examined using SEM), and the surface structures (including surface morphology, surface roughness, and surface compactness) of samples intercalated in water became ‘less compact’ and the degree of the ‘compactness’ of samples intercalated in scCO2 decreased further. Whether in water or scCO2, samples intercalated with TDTHP exhibited a larger basal spacing and the extent of disorder increased compared to that for samples intercalated with MTAB. The pristine MMT was also intercalated for comparison and silane grafting was proven to contribute to the increased basal spacing and ‘less compact’ surface structure.

In spring 2020, U.S. schools universally transitioned to online learning due to the COVID-19 pandemic’s onset, thus creating a natural experiment for examining adolescents’ risk and resilience during an ongoing school crisis response. This longitudinal study used a daily-diary approach to investigate the role of social support in the link between remote learning and psychological well-being across 64 days among a national sample of adolescents (n = 744; 42% Black, 36% White, 22% Other ethnicity/race; 41% boys; 72% eligible for free/reduced-priced lunch; Mage=14.60, SDage=1.71, age-range = 12–17 years). On days when youth attended remote learning, they reported lower daily positive affect, more daily stress, and higher parent social support. There were no significant differences in the effect of remote learning on affect or stress by race or economic status. On days when youth experienced more parent support, they reported lower daily stress and negative affect and higher daily positive affect. On days when youth experienced more peer support, they reported higher daily positive affect. Overall, the study highlights the impact of pandemic-onset remote learning on adolescents’ psychological well-being and emphasizes the need for future research on school crisis contingency planning to address these challenges.

Insect response to cold stress is often associated with adaptive strategies and chemical variation. However, low-temperature domestication to promote the cold tolerance potential of Bactrocera dorsalis and transformation of main internal substances are not clear. Here, we use a series of low-temperature exposure experiments, supercooling point (SCP) measurement, physiological substances and cryoprotectants detection to reveal that pre-cooling with milder low temperatures (5 and 10°C) for several hours (rapid cold hardening) and days (cold acclimation) can dramatically improve the survival rate of adults and pupae under an extremely low temperature (−6.5°C). Besides, the effect of rapid cold hardening for adults could be maintained even 4 h later with 25°C exposures, and SCP was significantly declined after cold acclimation. Furthermore, content of water, fat, protein, glycogen, sorbitol, glycerol and trehalose in bodies were measured. Results showed that water content was reduced and increased content of proteins, glycogen, glycerol and trehalose after two cold domestications. Our findings suggest that rapid cold hardening and cold acclimation could enhance cold tolerance of B. dorsalis by increasing proteins, glycerol, trehalose and decreasing water content. Conclusively, identifying a physiological variation will be useful for predicting the occurrence and migration trend of B. dorsalis populations.

Trace elements may play an important role in obesity. This study aimed to assess the plasma and dietary intake levels of four trace elements, Mn, Cu, Zn and Se in a rural Chinese population, and analyse the relationship between trace elements and obesity. A cross-sectional study involving 2587 participants was conducted. Logistic regression models were used to analyse the association between trace elements and obesity; restricted cubic spline (RCS) models were used to assess the dose–response relationship between trace elements and obesity; the weighted quantile sum (WQS) model was used to examine the potential interaction of four plasma trace elements on obesity. Logistic regression analysis showed that plasma Se concentrations in the fourth quartile (Q4) exhibited a lower risk of developing obesity than the first quartile (Q1) (central obesity: OR = 0·634, P = 0·002; general obesity: OR = 0·525, P = 0·005). Plasma Zn concentration in the third quartile (Q3) showed a lower risk of developing obesity in general obesity compared with the first quartile (Q1) (OR = 0·625, P = 0·036). In general obesity, the risk of morbidity was 1·727 and 1·923 times higher for the second and third (Q2, Q3) quartiles of dietary Mn intake than for Q1, respectively. RCS indicated an inverse U-shaped correlation between plasma Se and obesity. WQS revealed the combined effects of four trace elements were negatively associated with central obesity. Plasma Zn and Se were negatively associated with obesity, and dietary Mn was positively associated with obesity. The combined action of the four plasma trace elements had a negative effect on obesity.

Cryptosporidium spp. are significant opportunistic pathogens causing diarrhoea in humans and animals. Pigs are one of the most important potential hosts for Cryptosporidium. We evaluated the prevalence of Cryptosporidium in pigs globally using published information and a random-effects model. In total, 131 datasets from 36 countries were included in the final quantitative analysis. The global prevalence of Cryptosporidium in pigs was 16.3% (8560/64 809; 95% confidence interval [CI] 15.0–17.6%). The highest prevalence of Cryptosporidium in pigs was 40.8% (478/1271) in Africa. Post-weaned pigs had a significantly higher prevalence (25.8%; 2739/11 824) than pre-weaned, fattening and adult pigs. The prevalence of Cryptosporidium was higher in pigs with no diarrhoea (12.2%; 371/3501) than in pigs that had diarrhoea (8.0%; 348/4874). Seven Cryptosporidium species (Cryptosporidium scrofarum, Cryptosporidium suis, Cryptosporidium parvum, Cryptosporidium muris, Cryptosporidium tyzzeri, Cryptosporidium andersoni and Cryptosporidium struthioni) were detected in pigs globally. The proportion of C. scrofarum was 34.3% (1491/4351); the proportion of C. suis was 31.8% (1385/4351) and the proportion of C. parvum was 2.3% (98/4351). The influence of different geographic factors (latitude, longitude, mean yearly temperature, mean yearly relative humidity and mean yearly precipitation) on the infection rate of Cryptosporidium in pigs was also analysed. The results indicate that C. suis is the dominant species in pre-weaned pigs, while C. scrofarum is the dominant species in fattening and adult pigs. The findings highlight the role of pigs as possible potential hosts of zoonotic cryptosporidiosis and the need for additional studies on the prevalence, transmission and control of Cryptosporidium in pigs.

Hand, foot and mouth disease (HFMD) is a common infection in the world, and its epidemics result in heavy disease burdens. Over the past decade, HFMD has been widespread among children in China, with Shanxi Province being a severely affected northern province. Located in the temperate monsoon climate, Shanxi has a GDP of over 2.5 trillion yuan. It is important to have a comprehensive understanding of the basic features of HFMD in those areas that have similar meteorological and economic backgrounds to northern China. We aimed to investigate epidemiological characteristics, identify spatial clusters and predict monthly incidence of HFMD. All reported HFMD cases were obtained from the Shanxi Center for Disease Control and Prevention. Overall HFMD incidence showed a significant downward trend from 2017 to 2020, increasing again in 2021. Children aged < 5 years were primarily affected, with a high incidence of HFMD in male patients (relative risk: 1.316). The distribution showed a seasonal trend, with major peaks in June and July and secondary peaks in October and November with the exception of 2020. Other enteroviruses were the predominant causative agents of HFMD in most years. Areas with large numbers of HFMD cases were primarily in central Shanxi, and spatial clusters in 2017 and 2018 showed a positive global spatial correlation. Local spatial autocorrelation analysis showed that hot spots and secondary hot spots were concentrated in Jinzhong and Yangquan in 2018. Based on monthly incidence from September 2021 to August 2022, the mean absolute error (MAE), mean absolute percentage error (MAPE), and root mean square error (RMSE) of the long short-term memory (LSTM) and seasonal autoregressive integrated moving average (SARIMA) models were 386.58 vs. 838.25, 2.25 vs. 3.08, and 461.96 vs. 963.13, respectively, indicating that the predictive accuracy of LSTM was better than that of SARIMA. The LSTM model may be useful in predicting monthly incidences of HFMD, which may provide early warnings of HFMD epidemics.

We present a high-energy, hundred-picosecond (ps) pulsed mid-ultraviolet solid-state laser at 266 nm by a direct second harmonic generation (SHG) in a barium borate (BaB2O4, BBO) nonlinear crystal. The green pump source is a 710 mJ, 330 ps pulsed laser at a wavelength of 532 nm with a repetition rate of 1 Hz. Under a green pump energy of 710 mJ, a maximum output energy of 253.3 mJ at 266 nm is achieved with 250 ps pulse duration resulting in a peak power of more than 1 GW, corresponding to an SHG conversion efficiency of 35.7% from 532 to 266 nm. The experimental data were well consistent with the theoretical prediction. To the best of our knowledge, this laser exhibits both the highest output energy and highest peak power ever achieved in a hundred-ps/ps regime at 266 nm for BBO-SHG.

Pie charts are often used to communicate risk, such as the risk of driving. In the foreground-background salience effect (FBSE), foreground (probability of bad event) has greater salience than background (no bad event) in such a chart. Experiment 1 confirmed that the displays format of pie charts showed a typical FBSE. Experiment 2 showed that the FBSE resulted from a difference in cognitive efforts in processing the messages and that a foreground-emphasizing display was easier to process. Experiment 3 manipulated subjects’ information processing mindset and explored the interaction between displays format and information processing mindset. In the default mindset, careless subjects displayed a typical FBSE, while those who were instructed to be careful reported similar risk-avoidant behavior preference reading both charts. Suggestions for improving risk communication are discussed.