Hostname: page-component-6766d58669-zlvph Total loading time: 0 Render date: 2026-05-20T12:51:28.713Z Has data issue: false hasContentIssue false
  • English
  • Français

An improved method for parameter selection in finite element model updating

Published online by Cambridge University Press:  04 July 2016

M. J. Ratcliffe  and
N. A. J. Lieven
M. J. Ratcliffe
Affiliation:
Department of Aerospace EngineeringUniversity of BristolBristol, UK
N. A. J. Lieven
Affiliation:
Department of Aerospace EngineeringUniversity of BristolBristol, UK
Get access Rights & Permissions [Opens in a new window]

Abstract

Conventional wisdom states that coordinate complete experimental response data are required to effect a successful model update. This paper examines the influence measured rotational degrees of freedom have on the behaviour of the frequency response function (FRF) sensitivity updating procedure. Three finite element (FE) model-based case studies are undertaken which suggest that very little improvement is afforded by the inclusion of measured rotations in the updating process.

Error-location strategies in the past have yielded little qualitative information about the optimum selection of updating parameters in the model updating procedure. Two further cases are investigated; these suggest that no amount of coordinate completeness will rectify the debilitating effects of an inadequate p-value choice. A method of selecting the number and location of updating parameters — based on the FRF sensitivity method — is presented. This method is shown to yield promising results.

Information

Type
Research Article
Information
The Aeronautical Journal , Volume 102 , Issue 1016 , July 1998 , pp. 321 - 329
Copyright
Copyright © Royal Aeronautical Society 1998 

Access options

Get access to the full version of this content by using one of the access options below. (Log in options will check for institutional or personal access. Content may require purchase if you do not have access.)

Article purchase

Temporarily unavailable

References

1. Waters, T.P. Finite Element Model Updating Using Frequency Response Functions. PhD Thesis, Department of Aerospace Engineering, University of Bristol, UK, 1995.Google Scholar
2. Guyan, R.J. Reduction of mass and stiffness matrices, AIAA J, 1965, 3, (2), p 380.Google Scholar
3. Paz, M. Dynamic condensation method, AIAA J, 1984, 22, (5), pp 724–727.Google Scholar
4. Lieven, N.A.J. Validation of Structural Dynamic Models. PhD Thesis, Department of Mechanical Engineering, Imperial College of Science, Technology and Medicine, UK, 1990.Google Scholar
5. Visser, W.J. Updating Structural Dynamics Models Using Frequency Response Data. PhD Thesis, Department of Mechanical Engineering, Imperial College of Science, Technology and Medicine, UK, 1992.Google Scholar
6. Harder, R.L. and Desmarais, R.N. Interpolation using surface splines, J Aircr, February 1972, 9, pp 189–191.Google Scholar
7. Kidder, R.L. Reduction of structural frequency equations, AIAA J, 1973, 11, (3), p 892.Google Scholar
8. Lipkins, J. and Vandeurzen, U. The use of smoothing techniques for structural modification applications. 12th International Seminar on Modal Analysis, 1987, S1-3.Google Scholar
9. Ratcliffe, M.J. and Lieven, N.A.J. Measuring rotational degrees of freedom using a laser doppler vibrometer. Submitted to ASME, 1996. Accepted for Publication.Google Scholar
10. Duarte, M.L.M. and Ewins, D.J. Some insights into the importance of rotational degrees of freedom and residual terms in coupled structure analysis. IMAC XIII, 1995, pp 164–170.Google Scholar
11. Visser, W.J. and Imregun, M. A technique to update finite element models using frequency response data. IMAC LX, 1991, pp 462–468.Google Scholar
12. Maia, N. Fundamentals of singular value decomposition. IMAC LX, 1991, pp 1515–1521.Google Scholar
13. Mottershead, J.E., Friswell, M.I., Ng, N.G.T. and Brandon, J.A. Geometric parameters for finite element model updating of joints and constraints, Mech Systems and Signal Processing, 1996, 10, (2), pp 171–182.Google Scholar
14. Gladwell, G.M.L. and Ahmadian, H. Generic element matrices suitable for finite element model updating, Mech Systems and Signal Processing, 1995, 9, (6), pp 601–614.Google Scholar
15. Brüel, and kjær Frequency Analysis, DK-2850, Naerum, Denmark, ISBN 87 87355 07 8.Google Scholar
16. Allemang, R.J. and Brown, D.L. A correlation coefficient for modal vector analysis. IMAC I, 1983, pp 110–116.Google Scholar
17. Ziaei-Rad, S. and Imregun, M. On the accuracy required of experimental data for finite element model updating, J Sound and Vibration, 1996, 196, (3), pp 323–336.Google Scholar
18. Lieven, N.A.J., and Waters, T.P. Error location using normalised orthogonality. IMAC XII, 1994, pp 761–764.Google Scholar
19. Lieven, N.A.J. and Ewins, D.J. Spatial correlation of mode shapes, the coordinate modal assurance criterion (COMAC). IMAC VI, 1988, pp 690–695.Google Scholar