Skip to main content
×
Home
    • Aa
    • Aa

Experimental study of the pressure loss in aero-engine air-oil separators

  • A. Laura Cordes (a1), B. Tim Pychynski (a1), C. Corina Schwitzke (a1), D. Hans-Jörg Bauer (a1), A. Thiago P. de Carvalho (a2) and B. Hervé P. Morvan (a2)...
Abstract
ABSTRACT

The results of extensive experimental testing of an aero-engine air-oil separator are presented and discussed. The study focuses on the pressure loss of the system. Oil enters the device in the form of dispersed droplets. Subsequently, separation occurs by centrifuging larger droplets towards the outer walls and by film formation at the inner surface of a rotating porous material, namely an open-cell metal foam. The work described here is part of a study led jointly by the Karlsruhe Institute of Technology (KIT) and the University of Nottingham (UNott) within a recent EU project.

The goal of the research is to increase the separation efficiency to mitigate oil consumption and emissions, while keeping the pressure loss as low as possible. The aim is to determine the influencing factors on pressure loss and separation efficiency. With this knowledge, a correlation can eventually be derived. Experiments were conducted for three different separator configurations, one without a metal foam and two with metal foams of different pore sizes. For each configuration, a variety of engine-like conditions of air mass flow rate, rotational speed and droplet size was investigated. The experimental results were used to validate and improve the numerical modelling.

Results for the pressure drop and its dependencies on air mass flow rate and the rotational speed were analysed. It is shown that the swirling flow and the dissipation of angular momentum are the most important contributors to the pressure drop, besides the losses due to friction and dissipation caused by the flow passing the metal foam. It was found that the ratio of the rotor speed and the tangential velocity of the fluid is an important parameter to describe the influence of rotation on the pressure loss. Contrary to expectations, the pressure loss is not necessarily increased with a metal foam installed.

Copyright
Corresponding author
laura.cordes@kit.edu
Footnotes
Hide All

This paper will be presented at the ISABE 2017 Conference, 3-8 September 2017, Manchester, UK.

Footnotes
References
Hide All
1. GlahnA. and WittigS. Two-phase air/oil flow in aero engine bearing chambers: Characterization of oil film flows, Journal of Engineering for Gas Turbines and Power, 1996, 118, (3), p 578.
2. GlahnA., KurreckM., WillmannM. and WittigS. Feasibility study on oil droplet flow investigations inside aero engine bearing chambers—PDPA techniques in combination with numerical approaches, Journal of Engineering for Gas Turbines and Power, 1996, 118, (4), p 749, ISSN 07424795.
3. KrugM.B., PedutoD., KurzW. and BauerH.-J. Experimental investigation into the efficiency of an aero-engine oil jet supply system, Journal of Engineering for Gas Turbines and Power, 2015, 137, (1), p 011505. doi: 10.1115/1.4028255.
4. KurzW., DullenkopfK. and BauerH.-J. Influences on the oil split between the offtakes of an aero-engine bearing chamber, ASME Paper No. GT2012-69412, 2012, p 2251.
5. KurzW., DullenkopfK. and BauerH.-J. Capacitive film thickness measurements in a ventless aero-engine bearing chamber—influence of operating conditions and offtake design, Journal of Engineering for Gas Turbines and Power, 2013, 135, (11), p 112504. doi: 10.1115/1.4025067.
6. WittigS., GlahnA. and HimmelsbachJ. Influence of high rotational speeds on heat transfer and oil film thickness in aero engine bearing chambers, ASME Paper No. 93-GT-209, 1993.
7. GruselleF., SteimesJ. and HendrickP. Study of a two-phase flow pump and separator system, Journal of Engineering for Gas Turbines and Power, 2011, 133, (6), p 062401. doi:10.1115/1.4002470.
8. SteimesJ., GruselleF. and HendrickP. Performance study of an air-oil pump and separator solution, ASME Paper No. GT2012-68895, 2012, p 103.
9. SteimesJ., GruselleF. and HendrickP. Study of an air-oil pump and separator solution for aero engine lubrication systems, ASME Paper No. GT2013-94483, 2013, p V002T01A008.
10. FengJ., ChangY., PengX. and QuZ. Investigation of the oil–gas separation in a horizontal separator for oil-injected compressor units, Proceedings of the Institution of Mechanical Engineers, Part A: Journal of Power and Energy, 2008, 222, (4), pp 403412.
11. SheridanW.G., SwayzeS.T. and GlahnJ.A. De-oiler system for improved oil containment, ASME Paper No. GT2006-90035, 2006, pp 1283–1290.
12. WillenborgK., KlingspornM., TebbyS., RatcliffeT., GorseP., DullenkopfK. and WittigS. Experimental analysis of air-oil separator performance, Journal of Engineering for Gas Turbines and Power, 2008, 130, (6), ISSN 07424795.
13. KlingspornM. Advanced transmission and oil system concepts for modern aero-engines, ASME Paper No. GT2004-53578, 2004, pp 391–398.
14. de CarvalhoThiago P., MorvanH.P., HargreavesD., CordesL. and HöflerC. Numerical modelling of two-phase flow in aero-engine air/oil separators, ASME Paper No. GT2016-56633, 2016.
15. FarrallM., HibberdS., SimmonsK. and GiddingsD. Prediction of air/oil exit flows in a commercial aero-engine bearing chamber, Proceedings of the Institution of Mechanical Engineers, Part G: Journal of Aerospace Engineering, 2006, 220, (3), pp 197202.
16. CortesC. and GilA. Modeling the gas and particle flow inside cyclone separators, Progress in Energy and Combustion Science, 2007, 33, (5), pp 409452.
Recommend this journal

Email your librarian or administrator to recommend adding this journal to your organisation's collection.

The Aeronautical Journal
  • ISSN: 0001-9240
  • EISSN: 2059-6464
  • URL: /core/journals/aeronautical-journal
Please enter your name
Please enter a valid email address
Who would you like to send this to? *
×

Keywords:

Metrics

Full text views

Total number of HTML views: 3
Total number of PDF views: 31 *
Loading metrics...

Abstract views

Total abstract views: 115 *
Loading metrics...

* Views captured on Cambridge Core between 21st June 2017 - 23rd October 2017. This data will be updated every 24 hours.