The aerodynamic and structural design of a pitching blade tip with a double-swept planform is presented. The authors demonstrate how high-fidelity finite element (FE) and computational fluid dynamic (CFD) simulations are successfully used in the design phase. Eigenfrequencies, deformation, and stress distributions are evaluated by means of a three-dimensional (3D) FE model. Unsteady Reynolds-averaged Navier-Stokes (RANS) simulations are compared to experimental data for a light dynamic stall case at Ma = 0.5, Re = 1.2 × 106. The results show a very good agreement as long as the flow stays attached. Tendencies for the span-wise location of separation are captured. As soon as separation sets in, discrepancies between experimental and numerical data are observed. The experimental data show that for light dynamic stall cases at Ma = 0.5, a factor of safety of FoS = 2.0 is sufficient if the presented simulation methods are used.

A theory is presented on the effect of wake turbulence of a leading aircraft on the roll stability of a following aircraft, leading to a simple formula for the safe separation distance between the two aircraft that provides estimates of aircraft separation distances comparable to existing empirical regulations, based on experience. The formula includes the effects of flight and atmospheric conditions, and the characteristics of the leading and following aircraft; it applies to similar or dissimilar aircraft, and it indicates the parameters and conditions leading to increasing or decreasing separation. The formula is applied not only to the three International Civil Aviation Organization (ICAO) categories of aircraft (light, medium and heavy, respectively, Cessna Citation, B737 and B747) but also to ‘special’ aircraft requiring larger separation distance (Boeing 757) and to the world’s largest airliner (Airbus A380).

This paper investigates the problem of coning motion stability of spinning missiles equipped with strapdown seekers. During model derivation, it is found that the scaling factor error between the strapdown seeker and the onboard gyro introduces an undesired parasitic loop in the guidance system and, therefore, results in stability issues. Through stability analysis, a sufficient and necessary condition for the stability of spinning missiles with strapdown seekers is proposed analytically. Theoretical and numerical results reveal that the scaling factor error, spinning rate and navigation ratio play important roles in stable regions of the guidance system. Consequently, autopilot gains must be checked carefully to satisfy the stability conditions.

The unsteady air flow over and around the helicopter landing deck of a naval vessel is known to cause high pilot workload and to limit the helicopter's operational envelope for launch and recovery. Previous research has suggested that modifications to the ship's hangar edges can beneficially modify the flow over the deck. This paper examines the effectiveness of five hangar-edge modifications using computational fluid dynamics–generated airwakes and flight mechanics modelling, as well as piloted flight trials in a motion-base simulator. Results are presented, in terms of unsteady helicopter loads and pilot workload ratings, for modifications to the windward vertical rear edge of the hangar and with an oblique wind. The results demonstrate that while the airwake can be altered by superstructure modifications, the integrated effect of the altered airwake on the entire helicopter does not necessarily give the desired result; indeed of the five modifications tested, two were seen to be beneficial while three caused an increase in pilot workload compared with the unmodified hangar. Overall, the paper shows that the airwake can be modified by superstructure design changes, and that the effect on the helicopter can be measured through modelling and simulation. It is also demonstrated that making judgements on the severity of the airwake based on the aerodynamic flow field alone can be misleading. The benefit of these simulation tools is that they can be used during the ship design process to evaluate the effect of the superstructure aerodynamics, rather than wait until after the ship is built.

This design study applied parameterisation to rotor blade for improved performance. In the design, parametric equations were used to represent blade planform changes over the existing rotor blade model. Design variables included blade twist, sweep, dihedral and the radial control point. Updates to the blade structural properties with changes in the design variables allowed accurate evaluation of performance objectives and realistic structural constraints – blade stability, steady moments (flap bending, chord bending and torsion) and the high-g manoeuvre pitch link loads. Performance improvement was demonstrated with multiple parametric designs. Using a parametric design with advanced aerofoils, the predicted power reduction was 1.0% in hover, 10.0% at μ = 0.30 and 17.0% at μ = 0.40, relative to the baseline UH-60A rotor, but these were obtained with a 35% increase in the steady chord bending moment at μ = 0.30 and a 20% increase in the half peak-to-peak pitch link load during the UH-60A UTTAS manoeuvre. Low vibration was maintained for this design. More rigorous design efforts, such as chord tapering and/or structural redesign of the blade cross section, would enlarge the feasible design space and likely provide significant performance improvement.

This paper presents performance analysis and design of ducted propellers for lighter-than-air vehicles. High-fidelity computational fluid dynamics simulations were first performed on a detailed model of the propulsor, and the results were in very good agreement with available experimental data. Additional simulations were performed using a simplified geometry, to quantify the effect of the duct and of the blade twist on the propeller performance. It was shown that the duct is particularly effective at low flight speed and that the blades with relatively high twist have better performance over the flight envelope. Design of the optimal twist distribution and of the duct shape was also attempted by coupling the flow solver with a quasi-Newton optimisation method. Flow gradients were computed by solving the discrete adjoint of the Reynolds-averaged Navier-Stokes equations using a fixed-point iteration scheme or a nested Krylov method with deflated restarting. The results show that the ducted propeller propulsive efficiency can be increased by 2%.

Fatigue life is a random variable. Thus, the reliability of a conservative fatigue life prediction for a component in the helicopter dynamic system needs to be substantiated. A standard analytical substantiation method uses averaged manoeuvre loads instead of seeing manoeuvre loads as a random variable whose distribution is estimated with limited precision. This simplification may lead to inaccuracies. A new simulation-based method is developed to conservatively predict fatigue life, while also accounting for the full random distribution and uncertainty of manoeuvre loads. Both methods fully account for uncertain fatigue strength but assume that the mission profile is known or can at least be conservatively estimated. Simulations under synthetic but realistic engineering conditions demonstrate that both methods may be used for accurate substantiation of conservative fatigue life predictions. The simulations also demonstrate that, under the tested conditions, uncertainties from manoeuvre loads may be neglected in fatigue life substantiations as the resulting error is not significant with respect to uncertainties in component fatigue strength.