Hostname: page-component-7c8c6479df-p566r Total loading time: 0 Render date: 2024-03-29T10:49:43.332Z Has data issue: false hasContentIssue false

Remote-Sensing Studies of Kvitøyjøkulen, an Ice Cap on Kvitøya, North-East Svalbard

Published online by Cambridge University Press:  20 January 2017

Jonathan L. Bamber
Affiliation:
Mullard Space Science Laboratory, Department of Physics and Astronomy, University College London, Holmbury St Mary, Dorking, Surrey RH5 6NT, England
Julian A. Dowdeswell
Affiliation:
Scott Polar Research Institute, University of Cambridge, Cambridge CB2 1ER, England
Rights & Permissions [Opens in a new window]

Abstract

Airborne 60 MHz radio echo-sounding data were collected over 250 km of flight track from an ice cap (Kvitøyjøkulen) on Kvitøya in north-eastern Svalbard. These were combined with Landsat imagery to provide ice-surface and bed topographic information and inferences about the thermal and climatic conditions on the ice cap. Quantitative analysis of radio-echo strength measurements and the existence of offshore plumes of sediment-laden melt water indicate significant basal melting and a warmer thermal regime than would be expected from the geographical location of the ice cap. Analysis of the dielectric absorption of radio waves by the ice and data from a recently recovered ice core from a neighbouring ice cap (Austfonna) suggest considerable anthropogenic contamination of the precipitation falling on Kvitøya, most probably originating from Eurasia.

Type
Research Article
Copyright
Copyright © International Glaciological Society 1990

Introduction

Kvitøya is the most north-easterly island within the Svalbard archipelago, and is the island furthest from the relatively warm North Atlantic Drift, which flows along the west coast of Spitsbergen (Fig. 1). The ice cap on Kvitøya. Kvitøyjøkulen, therefore represents an end member to the suite of ice masses on Svalbard in terms of its relatively cold climate, low equilibrium-line altitude, and very high percentage of ice-covered island area (Reference LiestØlLiestol, in press). For this reason, Kvitøyjøkulen was included in an airborne radio echo-sounding survey of the ice masses on Svalbard, undertaken during spring 1983 (Reference Drewry and LiestolDrewry and Liestol, 1985; Reference DowdeswellDowdeswell and others, 1986; Dowdeswell, unpublished). The aims of this paper are: (i) to present information on the ice thickness, surface and bed topography of the ice cap; (ii) to examine echo-power measurements, which provide inform-ation on the bulk thermal regime and/or ice-impurity levels and the ice/bed interface; (iii) to compare echo-power data with those from other areas in Svalbard to help elucidate variations in thermal or basal conditions.

Perhaps because of its relatively harsh climate and inaccessibility, little was known about the glaciology or even the topography of Kvitøya until very recently. The island is infamous for the discovery in 1930 of the last camp of S.A. Andrée’s 1897 balloon expedition to the North Pole; hence the name Andreeneset at its western end (Fig. 1). It was not until the availability of Landsat satellite imagery from the mid-1970s that surveyors at the Norsk Polar-institutt were able to map the outline of Kvitøya with any accuracy and, more recently, vertical aerial photographs were obtained and the few areas of bare land fixed by satellite geoceiver. These data show Kvitøya has an area of 710 km2, of which 705 km2 is glacierized, forming the ice cap of Kvitoyjokulen (Reference LiestØlLiestol, in press). The ice cap ends in calving tide-water ice cliffs around 92% of its 115 km long margin (Fig. 1).

Fig. 1. The ice cap of Kvitøyjøkulen on Kvitøya, with the location of radio echo-sounding (light lines shown. Fliahl lines A-B and C-D were analysed for surface-slope distributions (Fig. 3). The Svalbard archipelago is inset.

Data Acquisition And Methods

Radio echo-sounding (RES) data were obtained using a SPRI Mk IV sounder operating at a centre frequency of 60 MHz. The geometric mean of eight individual wave forms, each comprising 256 samples taken at IOOns intervals, was recorded digitally. A detailed account of the digital recording system may be found in Reference Gorman and CooperGorman and Cooper (1987).

Data were also recorded in analogue “Z”-scope form using an oscillograph and heat-sensitive paper. The ice-surface elevation changes were tracked automatically, but for the weaker, noisier, and more intermittent bed echoes this was not possible. Instead, a power-differentiated continuous display was produced from the digital data and digitized manually. The errors in depth measurement incurred are negligible in comparison to the digital sampling length (equivalent to 8.4 m in ice, which defines the maximum resolution of an individual pulse).

Absolute elevations were calculated using terrain clearance from the radar sounder and a pressure altitude calibrated by overflying areas of open water. Interpolation between pulses enabled the relative surface elevation to be found to within 2 m (Dowdeswell, unpublished). Ice thicknesses were calculated using a mean value for the permittivity of ice of 3.17 (equivalent to an EM velocity of 168 m μs−1 in ice).

Navigation was carried out using a combination of a Tactical Airborne Navigation System (TANS) and coastal crossing points. Due to the relatively uniform nature of the coastline, across-track errors were fairly large — up to 1 km. Analysis of 32 flight-line crossing points over the ice cap produced a mean surface-elevation difference of 18.7 m.

Calibration of the radio-echo logarithmic receiver was achieved by flying over a calm sea surface, with an assumed power-reflection coefficient of unity, at a constant terrain clearance of 600 m. A variable attenuator with 10 dB steps placed in front of the receiver allowed the relationship between the digitally recorded power level and attenuation to be determined. The procedure was carried out at the start and the end of field work.

Landsat MSS images of Kvitøya were also acquired to provide: (i) a synoptic view of ice-surface elevations to complement the grid of RES data; (ii) data on the elevation of the snow line and areas of ice-surface melting; and (iii) information on the presence or otherwise of turbid, subglacially derived melt water around the ice-cap margins. MSS data in the form of computer-compatible tapes were obtained and analysed digitally on a GEMS image-processing system.

Radio Echo-Sounding Topographic Results

Ice-surface and bed morphology

The ice surface of Kvitøyjøkulen has been contoured at 50 m intervals. Landsat imagery was used to interpolate ice-surface contours between flight lines. The surface displays a relatively simple topography comprising two ice domes (Fig. 2). The eastern dome rises to a maximum measured elevation of 373 m a.s.l. The western dome is smaller in extent and altitude rising to a maximum recorded elevation of 324 m a.s.l. The true summits of these domes were not overflown and are likely to be 10–20 m higher than the maximum recorded values.

The frequency distribution of ice-surface slopes has been calculated for two transects along flow lines with a total length of about 50 km (Figs 1 and 3). Due to edge effects, slope angles are somewhat higher than typical values from the larger ice caps on Nordaustlandet to the west (Fig. 1) (Reference DowdeswellDowdeswell and Mclntyre, 1986). On Kvitøya only 60% of slopes are less than 1° and 71% are less than 1.5°.

Bed topography beneath Kvitøyjøkulen is also relatively simple, with slopes typically on the order of 0.7 or less (Fig. 4). Near the ice-cap margins, bed elevations drop below sea-level with a minimum observed value of 115mb.s.l. Elevations gradually increase inland with a maximum observed value of 72 m a.s.l. In substantial inland areas of the ice cap, however, no bed echoes were received due to high levels of absorption and internal scattering. These areas are indicated by dashed lines on the contour diagrams (Figs 4 and 5). Measured ice thicknesses ranged between approximately 100 and 300 m (Fig. 5).

Driving stresses were calculated along flight lines that follow ice-flow lines. Slopes were averaged over 4 km (approximately ten times the ice thickness). Where no bed elevations were present, usually in the central region, values were interpolated between data on either side of the gap. This introduces an error of up to 20% in the ice-thickness data but allows the general trends in driving stresses to be seen. Although the bedrock elevation has not been averaged, introducing a false high-frequency component, the overall pattern is clear. The driving stresses show values increasing to a maximum towards the ice-cap margins (Fig. 6a) with the lowest values being found in the regions of the two domes, as expected.

Fig. 2. Ice-surface contour map of Kvitøyjøkulen.

Theoretical long profiles

Theoretical ice-cap long profiles were calculated using the equation:

(1)

(Reference PatersonPaterson, 1981) where h s is surface elevation, L is the ice-mass half-width, and x is distance from the centre. The use of this equation assumes a flat, rigid bed with no basal sliding and no calving. Mass balance, temperature, and other factors influencing ice velocity are all assumed to be constant. Despite these fairly restrictive assumptions, in the absence of adequate boundary conditions, Equation (1) provides a qualitative indication of the stability of an ice cap (Reference PatersonPaterson, 1981). Figure 6b is a comparison of the theoretical and measured profile for the section of flight line A-B in Figure 1. It can be seen that for the western dome the theoretical profile is significantly lower than the observed profile. Combined with a relatively high driving stress in this area (Fig. 6a), this suggests that the bed may be frozen here. For the eastern dome there is good agreement between the two profiles.

Fig. 3. Histogram of ice-surface slopes along Ihe transects A-B and C-D (Fig. 1).

Most of the other flight lines do not follow flow lines and therefore cannot be used for this analysis but those that do showed similar agreement to that indicated in Figure 6b.

The distribution of driving stresses and long profiles has a similar pattern to those of a number of drainage basins on Austfonna, Nordaustlandet (Reference DowdeswellDowdeswell, 1986). On Austfonna, three distinct groups of drainage basin were identified on the basis of their long profile and driving stresses. Basins with low driving stresses and surface profiles (relative to theoretical profiles derived from Equation (1)) were associated with observed surge activity, whereas none of those with high driving stresses and surface profiles had been observed to undergo surging. It is inferred, therefore, by comparison with the behaviour of the neighbouring ice caps on Nordaustlandet, that the driving-stress distribution and surface profiles on Kvitøyjøkulen do not indicate thai surges have occurred in the recent past.

Landsat imagery and subglacial water

Beyond the margins of Austfonna, the presence of turbid plumes of subglacially derived melt water has been used to infer the existence of basal melting (Reference Dowdeswell, Drewry, Cooper, Gorman, Liestøl and OrheimDowdeswell and Drewry, 1989). Digital enhancement of sea-surface pixels from Landsat CCIs shows similar surface sediment plumes emanating from point sources in the terminal ice cliffs of Kvitøyjøkulen. Watcr-turbidity measurements off the coast of Nordaustlandet confirm that features similar to those illustrated are a result of sediment-laden waters (Reference Dowdeswell, Drewry, Cooper, Gorman, Liestøl and OrheimDowdeswell and Drewry, 1989). Although cloud obscures parts of the coast of Kvitøya, these plumes appear to occur at intervals around most of the ice cap (Fig. 7). T hese turbid melt waters come to the surface as they leave the confines of the ice cap because they are generally less dense than the ocean waters into which they flow. Their sediment content must come from the ice/bed interface, because there are no rock outcrops to provide a source of supraglacial debris. The presence of point sources for the sediment plumes also indicates that significant subglacial channels are formed and that, despite its location, the ice cap possesses significant areas of basal melting.

Echo-strength measurements

Measurement of the returned signal strength from the ice/substrate interface can provide information on both the

Fig. 4. Bed topography of Kvitøya deduced from radio echo-sounding data. Dashed lines reprisent regions of interpolated contours due to poor radio-echo returns from these areas.

Fig. 5. Ice-thickness contour map for Kvitøyjøkulen deduced from radio echo-sounding dala. Dashed lines represent regions of interpolated contours due to poor radio-echo returns from these areas.

Fig. 6. a. Driving stresses along the flow line A-B in Figure 1. Ice-surface slopes were averaged over 4 km (approximately 10–15 times the ice thickness), b. Observed (solid line) and theoretical (dashed line) ice-surf aoe profile along a section of the flight line in Figure 1.

Fig. 7. Plumes of suspended sediment exiting from the sub-glacial drainage system of Kvitøyjøkulen — digitally enhanced Landsal MSS bands 4, 5, and 7 acquired on 21 July 1979.

nature of the interface and the bulk properties of the ice overlying it. Two parameters of interest can be derived from the returned echo strength. The first is the mean dielectric absorption, B (in (dB m−1). This is related to the real part of the high frequency conductivity of the ice, σ′ by the equation:

(2)

where c is the velocity of light in vacuo, ε0 is the permittivity of free space, and ε′ is the real part of the relative permittivity of ice. The absorption is directly proportional to σ′, and is usually influenced primarily by the ice temperature, through an Arrhenius-type equation. It is also, however, strongly influenced by the presence of impurities (Reference Gross, Hayslip and HoyGross and others, 1978; Reference Moore, Mulvaney and ParenMoore and others, 1989) and to a lesser extent by crystal-fabric and density variations.

The second parameter of interest is the power-reflection coefficient (PRC) of the ice/bed interface. This is determined from the radar equation which, in logarithmic form, can be expressed as:

(3)

where P r and P t are the received and transmitted power, respectively, G is the antenna gain, λ0 is the free-space wavelength, H is the terrain clearance, z is the ice thickness, R is the power-reflection coefficient, B(z) is the dielectric absorption in dB m−1, and L is antenna mismatch and cable losses. To obtain R, this equation requires a knowledge of the system parameters (P t. G, and L). However, from the calibration graph for the receiver, it is possible to eliminate these constants by using the intercept (i.e. when the attenuation = 0) to fix the value of the attenuation calculated from the radio echo-sounding data. The PRC (in dB, i.e. PRC = 10logR) is then given as:

(4)

where m is the gradient of the calibration graph, C is a constant determined by the intercept and the geometrical spreading term for the calibration flight, D is the digital value of signal strength, and n is the refractive index = (ε′)½.

The PRC is dependent on the dielectric properties of the substrate and will vary according to the rock type (Bamber, unpublished). It is also very sensitive to the presence of water (Bamber. unpublished) which has a relative permittivity of between 10 and 20 times that of most rocks (Reference ParkhomenkoParkhomenko, 1967) and can also have a much higher conductivity than dry rock (Reference Collins and YoungCollins and Young, 1981). Consequently, even relatively small quantities of water at the bed can increase PRCs by 10 dB or more. An additional factor that influences the value of PRC is the metre-scale roughness of the bed. This can reduce the returned power by up to 15 dB (Neal, unpublished).

Echo-strength results

Absorption values

The only unknowns in Equation (4) are the PRC and B(z). If the geometrical spreading term is removed, these represent the total attenuation of the radar wave (due to absorption and reflection losses):

(5)

Hence, if the total attenuation is plotted against ice thickness for a given ice mass, the gradient of the plot is 2 B (where the overbar denotes the mean value integrated over the total ice thickness) and the intercept is the PRC (Fig. 8). This assumes that the data are statistically stationary over the area being investigated, that is, that both B and the bed PRC are invariant. This is clearly an approximation as the mean temperature would be expected to vary with ice thickness and elevation. The justification for this approximation was assessed by the spread in points about the fitted regression line. Pearson’s product-moment correlation coefficient was used to quantify this. Data with a correlation of <0.8 were considered to possess an unsatisfactory linear fit.

Fig. 8. Scatter plot of ice thickness versus attenuation for all the valid data over Kvitøra.

It would be expected that, if the primary influence on absorption in Svalbard is temperature, then Kvitøyjøkulen should, due to its location at the north-eastern extremity of the archipelago, have the lowest value. It might also be expected that there would be some variation with altitude. A number of different methods of grouping the data were investigated to establish whether there were any areal variations in absorption. Data from Austfonna, Nordaustlandet (the largest ice cap in the archipelago), were found to vary monotonically with elevation, and lower values (presumably indicating lower temperatures) were found at higher elevations (Bamber, unpublished). A similar analysis was undertaken for Kvitøya but, partly due to the less extensive coverage, no significant relationship was found. The absorption values were also separated into two groups divided by the approximate elevation of the equilibrium line (Reference LiestØlLiestøl, in press) but again no improvement in the correlation coefficients was obtained. Analysis of the whole data set gave a mean B of 7.48 ± 0.2 dB/100 m for 787 points with a correlation coefficient of 0.83 (Fig. 8).

There is a change in rock type from mainly granitic migmatites in the west of Kvitøya to quartz-diorite in the east, although the location of the geological boundary is not known (Reference Lauritzen and OhtaLauritzen and Ohta, 1984). Examination of PRC data indicates a discontinuity of approximately 8 dB between values lying either side of a line running from lat. 80°13′N., long. 31°54′E. to lat. 80°09′N., long. 32°26Δ E. Separating the RES data along this line produces a considerable improvement in the value of the correlation coefficient for each group. The western and eastern parts gave, respectively, a mean absorption of 8.05 ± 0.2 and 7.49 ± 0.2 dB/100 m with correlation coefficients of 0.90 and 0.89. These absorption values are equivalent to conductivities of 88 and 81 μS m−1. respectively, and are considerably higher than values obtained elsewhere in Svalbard (Reference BamberBamber, 1989, unpublished). These range from approximately 4.5 dB/100 m in western Spitsbergen to a maximum of 5.4 dB/100 m on Austfonna, the largest ice cap in the archipelago (Fig. 9).

Fig. 9. Representative selection of mean radio-wave absorption values (dB/100 m) in Svalbard, indicating the regional pattern.

Power-reflection coefficients

The greatest errors jnvolved in calculating the PRCs are in the estimation of B Experimental random errors are about ±2.4 dB, while errors from B are of the order of ±2 dB/100m and can introduce an uncertainty of between 2 and 7 dB depending on ice thickness. Using the values of B obtained in the previous section produced some unrealistically high values of PRC (including one or two positive values). A possible explanation for the apparent unsuitability of the calculated values will be given in the next section. Using lower values (more typical of the rest of Svalbard) still produced relatively high PRCs for Kvitøya, ranging between −5 and −25 dB.

A distinct geographical trend was observed for the PRC data (Fig. 10) for the Svalbard archipelago. The highest values (-8 to −15 dB) were found in western Spitsbergen and are believed to be associated with the presence of significant quantities of water at the glacier bed (Reference BamberBamber, 1989, unpublished). Relatively low values (-30 to −40 dB) were calculated for parts of the high-plateau ice caps in north-east Spitsbergen and were suggested to be due to a frozen bed most probably overlain by a debris-rich layer of ice (Reference BamberBamber, 1989). Austfonna was found to have intermediate values (between −17 and −30 dB) but, as for the ice masses in Spitsbergen, there was a proportionality between PRCs and mean absorption values. Intuitively, this seems reasonable as high B values suggest higher temperatures and hence a greater presence of basal water.

Fig. 10. Representative selection of mean bed-power reflection coefficients (dB) in Svalbard, indicating the regional pattern.

Discussion

The pattern of absorption values is shown in Figure 10. Although there is a less obvious trend in comparison to the PRCs, it is interesting to note that the two theoretically coldest ice masses (on the grounds of location and limited temperature data) in the archipelago, Austfonna and Kvitøyjøkulen, possess the highest absorption values. In addition, those from Kvitøya are approximately 40% higher than the highest value from Austfonna. If it were only temperature regulating absorption, then the bulk ice temperature for Kvitøya should be about 5°C warmer than for the warmest ice on Austfonna. This is unlikely as Kvitøya is in the coldest part of the Svalbard archipelago; there is a maximum elevation difference between them of 200 m and Landsat data suggest that both ice caps possess significant basal melting (Fig. 7). It is clear that another factor is having a strong influence on the dielectric properties of the ice. Factors, other than temperature, that can influence dielectric absorption include crystal fabric, density, the presence of water (linked to temperature), and impurity content (Reference Glen and ParenGlen and Paren, 1975). Assuming sensible physical limits for the variations in these parameters, the only factor that can produce such a marked increase in absorption is an increase in the impurity content.

Shallow snow samples have been collected from a number of different sites in Svalbard and showed a two- to three-fold increase in H+ concentration between Spitsbergen and Austfonna (Reference Semb, Brækkan and JorangerSemb and others, 1984). The highest value observed was obtained from near the summit of Austfonna and is equivalent to a pH of 4.53. It implies strongly acidified precipitation that is most likely of an anthropogenic origin. It has been shown that the wintertime air circulation in the Arctic originates from Eurasia and travels over Siberia, across the Arctic Ocean, approaching Svalbard from the east (Reference Rahn, Rey and StonehouscRahn, 1982). In summer, however, due to the retreat of the Arctic Front to higher latitudes, the air masses often come from the Atlantic and Iceland, and approach Svalbard from the west (Reference BarrieBarrie, 1986).

Furthermore, studies of air pollution in the Arctic (Reference Rahn, Joranger, Semb and ConwayRahn and others, 1980) indicate much higher SO2 levels in the winter (December-March). There may be, therefore, an east/west gradient in impurity concentration in the precipitation over Svalbard. The ice mass lying at the extreme of this gradient is Kvitøyjøkulen. The ice cap is of sufficient altitude to cause substantial precipitation and moisture loss from approaching easterly air masses (Reference MasonMason, 1971). The winter air stream will then pass over Austfonna and finally Spitsbergen. In summer, it is suggested that the majority of moisture is removed in traversing Spitsbergen from the west and little falls over Kvitøya.

A second factor that may enhance the proposed impurity gradient is melt-water percolation. It has been suggested that the existence of water at grain boundaries in temperate glaciers can remove the bulk of the impurities from the ice (Reference Glen, Homer and ParenGlen and others, 1977). On theoretical grounds, it has also been suggested that acids reside at grain boundaries (Reference Wolff and ParenWolff and Paren, 1984). Preliminary results from scanning electron microscopy of natural ice samples support this hypothesis (Wolff and Mulvaney, unpublished). The greater amounts of surface melt water present in Spitsbergen due to higher summer temperatures in the west of the archipelago would consequently produce more “impurity flushing” than on Austfonna or Kvitøya (which would presumably be least affected by this process).

It is important to consider the time-scale over which high levels of impurities (specifically acids) have been affecting the Arctic. Results from an ice core taken from Dye 3, Greenland, suggest that significant increases have taken place over approximately the last 100 years (Reference Neftel, Beer, Oeschger, Z�rcher and FinkelNeftel and others, 1985). The accumulation rate on the summit of Austfonna is on the order of 0.4–0.5 m/year (Reference Dowdeswell, Drewry, Cooper, Gorman, Liestøl and OrheimDowdeswell and Drewry, 1989). The order of magnitude of the time-scale and accumulation rate are strongly supported by data obtained from a Soviet ice core taken from the summit of Austfonna which displays a minimum pH at the surface of 5.2–5.3, steadily increasing to a fairly constant value of about 5.6 at a depth of 80–100 m (paper in preparation by V.S. Zagarodnov and S.M. Arkhipov).

The equilibrium line on Kvitøya lies at an elevation of about 200 m a.s.l. (Reference LiestØlLiestol, in press). Analysis of digital Landsat imagery confirms this value. The majority of ice below this level will be older than 100 years and consequently relatively “clean”. Hence, the impure ice layer will form a “cap” lying over an almost flat layer of relatively pure ice. This lower layer, being reasonably uniform in thickness, would not be detected by plotting ice thickness against absorption and might explain why using the calculated values of B gave unrealistically high PRCs. If a different model is used with a low-loss bottom layer of approximately 200 m thickness, then more realistic PRCs are obtained.

Let us assume that the increase in absorption on Kvitøya relative to the values on Nordaustlandet is due solely to an increase in H+. Using an empirically derived relationship between conductivity and H+ (Reference Moore, Mulvaney and ParenMoore and others, 1989), it is then possible to estimate δH+. The relationship is, however, temperature-dependent and the uncertainty in the temperature profile and the dependence means that the calculated value is only an “order-of-magnitude” estimate. The difference in absorption between the two ice masses is about 3 dB/100 m. This implies a difference in conductivity of 33 μS m−1 which, in turn, indicates a δH+ of 13 ± 6 μmol. This suggests more than a doubling in the acidity, which seems unlikely. If, however, the mean ice temperature for Kvitøya is higher than that for Nordaustlandet, then this would have the dual effect of increasing the influence of impurities and the intrinsic conductivity of the ice. It is unlikely that the ice from Kvitøya would contain a much greater concentration of sea salts compared with Nordaustlandet as the surface elevations are not too dissimilar and the sea-ice cover is greatest in extent both temporally and spatially in the extreme north-east.

Conclusions

The morphology of Kvitøya suggests a relatively stable ice cap with simple ice-surface and bed topography. The existence of debris-rich plumes of melt water offshore implies that there are areas of basal melting beneath the ice cap. Furthermore, significant areas of the bed are below sea-level, and any advance of the ice-cap margins would be over potentially deformable glaciomarine sediments.

Echo-strength measurements have indicated an anomolously high radio-wave absorption relative to other ice masses sounded in Svalbard. It is believed that this is due to a higher level of anthropogenic impurities in the snow on Kvitøya than elsewhere in the archipelago and to a lower amount of melt-water percolation. This is associated with winter air circulation supplying polluted air from Eurasia. This hypothesis could be easily tested with an ice core or, less satisfactorily, from shallow snow measurements.

Acknowledgements

The data on which this work is based were collected as part of a collaborative project between the Scott Polar Research Institute, University of Cambridge, and the Norsk Polarinstitutt, Oslo. Funding came from U.K.. NERC Research Grant GR3/4663 to Drs J.A. Dowdeswell and D.J. Drewry. The authors would like to thank Dr D.J. Drewry for his advice and comments.

References

Bamber, J.L. 1989 Ice/bed interface and englacial properties of Svalbard ice masses deduced from airborne radio echo–sounding data. J. Glacial., 35(119), 3037.Google Scholar
Bamber, J.L. Unpublished. Radio echo sounding studies of Svalbard glaciers. (Ph.D. thesis. University of Cambridge, 1987)Google Scholar
Barrie, L.A. 1986 Arctic air pollution: an overview of current knowledge. Atmos. Environ., 20(4), 643663.Google Scholar
Collins, D.N. Young, G.J.. 1981 Meltwater hydrology and hydrochemistry in snow– and ice–covered mountain catchments. Nord. Hydrol., 12(45), 319334.CrossRefGoogle Scholar
Dowdeswell, J.A. 1986 Drainage–basin characteristics of Nordaustlandet ice caps Svalbard.. J. Glacial., 32(110), 3138.CrossRefGoogle Scholar
Dowdeswell, J.A. Unpublished. Remote sensing studies of Svalbard glaciers. (Ph.D. thesis, University of Cambridge. 1984)Google Scholar
Dowdeswell, J.A. Drewry, D.J.. 1989 The dynamics of Austfonna, Nordaustlandet, Svalbard: surface velocities, mass balance, and subglacial melt water. Ann. Clacinl., 12, 3745.Google Scholar
Dowdeswell, J.A. Mclntyre, N.F.. 1986 The saturation of Landsat MSS detectors over large ice masses. Int. J. Remote Sensing, 7(1), 151164.Google Scholar
Dowdeswell, J.A. Drewry, D.J. Cooper, A.P.R. Gorman, M.R. Liestøl, O. Orheim, O.. 1986 Digital mapping of the Nordaustlandet ice caps from airborne geophysical investigations. Ann. Glaciol., 8, 5158.Google Scholar
Drewry, D.J. Liestol, O.. 1985 Glaciological investigations of surging ice caps in Nordaustlandet Svalbard, 1983. , Polar Ree, 22(139), 359378.Google Scholar
Glen, J.W. Paren, J.G.. 1975 The electrical properties of snow and ice. J. Glacial., 15(73), 1538.CrossRefGoogle Scholar
Glen, J.W. Homer, D.R. Paren, J.G.. 1977 Water at grain boundaries: its role in the purification of temperate glacier ice. International Association of Hydrological Sciences Publication 118 (Symposium at Grenoble 1975 — Isotopes and Impurities in Snow and Ice), 263271.Google Scholar
Gorman, M.R. Cooper, A.P.R.. 1987 A digital radio echo–sounding and navigation recording system. Ann. Glacial., 9, 8184.Google Scholar
Gross, G.W. Hayslip, I.C. Hoy, R.N.. 1978 Electrical conductivity and relaxation in ice crystals with known impurity content. J. Glacial., 21(85), 143160.Google Scholar
Lauritzen, Ø Ohta, Y.. 1984 Geological map of Svalbard 1 :500,000. Sheet 4G. Nordaustlandet. Nor. Polarinst. Skr. 154 D.Google Scholar
LiestØl, O. In press. Glaciers of Svalbard, Norway. U.S. Geol. Surv. Prof. Pap. 1386 Google Scholar
Mason, B.J. 1971 The physics of clouds. Second edition. Oxford, Clarendon Press.Google Scholar
Moore, J.C. Mulvaney, R. Paren, J.G.. 1989 Dielectric stratigraphy of ice: a new technique for determining total ion concentrations in polar ice cores. Geophvs. Res. Lett., 16(10), 11771180.CrossRefGoogle Scholar
Neal, C.S. Unpublished. Radio echo sounding studies of the Ross Ice Shelf. (Ph.D. thesis, University of Cambridge. 1977)Google Scholar
Neftel, A. Beer, J. Oeschger, H. Z�rcher, F. Finkel, R.C.. 1985 Sulphate and nitrate concentrations in snow from south Greenland 1895–1978. Nature, 314(6012), 61 1613.Google Scholar
Parkhomenko, E.I. 1967 Electrical properties of rocks. New York, Plenum Press.Google Scholar
Paterson, W.S.B. 1981 The physics of glaciers. Second edition. Oxford, etc., Pergamon Press.Google Scholar
Rahn, K.A. 1982 On the causes, characteristics and potential environmental effects of aerosol in the Arctic atmosphere. In Rey, L,Stonehousc, B, eds. The Arctic Ocean: the hydrographie environment and the fate of pollutants. London, Macmillan, 163195.Google Scholar
Rahn, K.A. Joranger, E. Semb, A. Conway, T.J.. 1980 High winter concentrations of SO2 in the Norwegian Arctic and transport from Eurasia. Nature, 287(5785), 824826.Google Scholar
Semb, A. Brækkan, R. Joranger, E.. 1984 Major ions in Spitsbergen snow samples. Geophys. Res. Lett., 11(5), 445448.Google Scholar
Wolff, E.W. Mulvaney, R.. Unpublished. Further observations on the location of impurities in Antarctic ice. A paper presented at the British Branch Meeting of the International Glaciological Society, Manchester, September 1988.Google Scholar
Wolff, E.W. Paren, J.G.. 1984 A two–phase model of electrical conduction in polar ice sheets. J. Geophvs. Res., 89(B11), 94339438.Google Scholar
Figure 0

Fig. 1. The ice cap of Kvitøyjøkulen on Kvitøya, with the location of radio echo-sounding (light lines shown. Fliahl lines A-B and C-D were analysed for surface-slope distributions (Fig. 3). The Svalbard archipelago is inset.

Figure 1

Fig. 2. Ice-surface contour map of Kvitøyjøkulen.

Figure 2

Fig. 3. Histogram of ice-surface slopes along Ihe transects A-B and C-D (Fig. 1).

Figure 3

Fig. 4. Bed topography of Kvitøya deduced from radio echo-sounding data. Dashed lines reprisent regions of interpolated contours due to poor radio-echo returns from these areas.

Figure 4

Fig. 5. Ice-thickness contour map for Kvitøyjøkulen deduced from radio echo-sounding dala. Dashed lines represent regions of interpolated contours due to poor radio-echo returns from these areas.

Figure 5

Fig. 6. a. Driving stresses along the flow line A-B in Figure 1. Ice-surface slopes were averaged over 4 km (approximately 10–15 times the ice thickness), b. Observed (solid line) and theoretical (dashed line) ice-surf aoe profile along a section of the flight line in Figure 1.

Figure 6

Fig. 7. Plumes of suspended sediment exiting from the sub-glacial drainage system of Kvitøyjøkulen — digitally enhanced Landsal MSS bands 4, 5, and 7 acquired on 21 July 1979.

Figure 7

Fig. 8. Scatter plot of ice thickness versus attenuation for all the valid data over Kvitøra.

Figure 8

Fig. 9. Representative selection of mean radio-wave absorption values (dB/100 m) in Svalbard, indicating the regional pattern.

Figure 9

Fig. 10. Representative selection of mean bed-power reflection coefficients (dB) in Svalbard, indicating the regional pattern.