Hostname: page-component-8448b6f56d-jr42d Total loading time: 0 Render date: 2024-04-25T04:17:26.204Z Has data issue: false hasContentIssue false
  • English
  • Français

Electrochemical noise analysis of Ti-15Mo alloy samples exposed to Hanks solution: association between milling time and corrosion resistance

Published online by Cambridge University Press:  05 December 2017

J.C. Betancourt-Ruiz ,
C.G. Nava-Dino ,
Claudia Lerma  and
R.R. Torres-Knight
J.C. Betancourt-Ruiz
Affiliation:
Facultad de Ingeniería, Universidad Autónoma de Chihuahua, Circuito Universitario s/n, Nuevo Campus Universitario, Chihuahua, Chihuahua. C.P. 31100. México
C.G. Nava-Dino*
Affiliation:
Facultad de Ingeniería, Universidad Autónoma de Chihuahua, Circuito Universitario s/n, Nuevo Campus Universitario, Chihuahua, Chihuahua. C.P. 31100. México
Claudia Lerma
Affiliation:
Departamento de Instrumentación Electromecánica, Instituto Nacional de Cardiología Ignacio Chávez, Juan Badiano 1, Col. Sección 16, Ciudad de México. C.P. 14080. México
R.R. Torres-Knight
Affiliation:
Facultad de Ingeniería, Universidad Autónoma de Chihuahua, Circuito Universitario s/n, Nuevo Campus Universitario, Chihuahua, Chihuahua. C.P. 31100. México
*
*(Email: ndino@uach.mx)
Get access

Abstract

The aim of this work was to evaluate the corrosion resistance of Ti15Mo alloys prepared with different milling times (0, 3, 5 and 8 hours) and exposed to Hanks solution. The alloys of Ti-15Mo were prepared by mechanical milling under an Ar atmosphere. SPEX 8000M was connected to a hardened steel container with 13 mm (Ø) balls as milling media, using alternate cycles of 30 minutes milling and 30 min resting. Milling time longer than 8 hours using Ti alloys were avoided to prevent oxidation. The electrochemical noise time series of current (I) and voltage (V) were used to calculate the Rn corrosion index = voltage SD / current SD; SD = standard deviation. Rn was calculated from the original data and also from data after drift removal with two fitting procedures: cubic polynomial (degree 3) and moving average. A significant inverse association (p < 0.05, Spearman’s correlation analysis) between milling time and Rn was found in time series fitted by a polynomial, which indicates higher corrosion resistance among samples prepared with longer milling times. The recurrence plot analysis showed that the fitting method also influenced the dynamical behaviour of these time series.

Keywords

biomaterialcorrosionmechanical alloying
Type
Articles
Information
MRS Advances , Volume 2 , Issue 61: International Materials Research Congress XXV , 2017 , pp. 3837 - 3844
Check for updates
Copyright
Copyright © Materials Research Society 2017 

Access options

Get access to the full version of this content by using one of the access options below. (Log in options will check for institutional or personal access. Content may require purchase if you do not have access.)

References

REFERENCES

Mills, D., Picton, P., Mularczyk, L., Developments in the electrochemical noise method (ENM) to make itmore practical for assessment of anti-corrosive coatings Douglas, Electrochimica Acta 124, 199–205 (2014).Google Scholar
Somsanitha, N., Sankara Narayanana, T.S.N., Kima, Y.K., Parkb, I.S., Baea, T.Su., Leea, M.H., Surface medication of Ti–15Mo alloy by thermal oxidation: Evaluation of surface characteristics and corrosion resistance in Ringer’s solution, Applied Surface Science 356 1117–1126, (2015).Google Scholar
Kazek-Kęsik, A., Krok-Borkowicz, M., Pamuła, E., Simka, W., Electrochemical and biological characterization of coatings formed on Ti–15Mo alloy by plasma electrolytic oxidation, Materials Science and Engineering C 43, 172–181, (2014).Google Scholar
Cottis, R.A., The effects of solution resistance on electrochemical noise resistance measurements:A theoretical analysis, in: Kearns, J.R.; Scully, J.R., Electrochemical Noise Measurement for Corrosion Applications, Special Testing Publications 1277, ASTM International, ISBN 978-0-8031-2032-7(1996).Google Scholar
López-Meléndez, C., García-Ochoa, E.M., Flores-Zamora, M.I., Bautista-Margulis, R.G., Carreño-Gallardo, C., Castillo-Morquecho, C.P., Chacón-Nava, J.G., Martínez-Villafañe, A., Dynamicstudy of current fluctuations of nanostructured films, Int. J. Electrochem. Sci. 7 1160–1169, (2012).Google Scholar
Yang, Y., Zhang, T., Shao, Y., Meng, G., Wang, F., Effect of hydrostatic pressure on the corrosion behavior of Ni–Cr–Mo–V high strength steel. Corros. Sci. 52 2697–2706, (2010) .Google Scholar
Acuña-González, N., García-Ochoa, E., González-Sánchez, J., Assessment of the dynamics of corrosion fatigue crack initiation applying recurrence plots to the analysis of electrochemical noise, Int. J. Fatigue 30, 1211–1219 (2008).Google Scholar
Mhalsekar, S.D., Rhao, S.S., Gangadharan, K.V., Investigation on feasibility of recurrence quantification analysis for detecting flank wear in face milling. Int. J. Eng. Sci. Tech. 2(2010) 23–38.Google Scholar
Cazares-Ibáñez, E., Vázquez-Coutiño, G.A., García-Ochoa, E.. Application of recurrence plots as a new tool in the analysis of electrochemical oscillations of cooper, J. Electroanalytical Chem. 583, 17–33, (2005).Google Scholar
Marwan, N., Encounters with neighbours: current developments of concepts based on recurrence plots and their application, PhD Thesis, University of Potsdam, Potsdam. 2003; 1–87Google Scholar