Hostname: page-component-7dd5485656-frp75 Total loading time: 0 Render date: 2025-10-31T02:56:59.556Z Has data issue: false hasContentIssue false
  • English
  • Français

Preparation of a-Si:H and a-SiGe:H I-Layers for Nip Solar Cells at High Deposition Rates Using a Very High Frequency Technique

Published online by Cambridge University Press:  10 February 2011

S.J. Jones ,
X. Deng ,
T. Liu  and
M. Izu
S.J. Jones
Affiliation:
Energy Conversion Devices, Inc., Troy, MIl 48084
X. Deng
Affiliation:
Energy Conversion Devices, Inc., Troy, MIl 48084
T. Liu
Affiliation:
Energy Conversion Devices, Inc., Troy, MIl 48084
M. Izu
Affiliation:
Energy Conversion Devices, Inc., Troy, MIl 48084
Get access

Abstract

The 70 MHz Plasma Enhance Chemical Vapor Deposition (PECVD) technique has been tested as a high deposition rate (10 A/s) process for the fabrication of a-Si:H and a-SiGe:H alloy ilayers for high efficiency nip solar cells. As a prelude to multi-junction cell fabrication, the deposition conditions used to make single-junction a-Si:H and a-SiGe:H cells using this Very High Frequency (VHF) method have been varied to optimize the material quality and the cell efficiencies. It was found that the efficiencies and the light stability for a-Si:H single-junction cells can be made to remain relatively constant as the i-layer deposition rate is varied from 1 to 10 Å/s. Also these stable efficiencies are similar to those for cells made at low deposition rates (1 Å/s) using the standard 13.56 MHz PECVD technique. For the a-SiGe:H cells of the same i-layer thickness, use of the VHF technique leads to cells with higher currents and an ability to more easily current match triple-junction cells prepared at high deposition rates which should lead to higher multi-junction efficiencies. Thus, use of this VHF method in the production of large area a- Si:H based multi-junction solar modules will allow for higher i-layer deposition rates, higher manufacturing throughput and reduced module cost.

Information

Type
Research Article
Information
MRS Online Proceedings Library (OPL) , Volume 507: Symposium A – Amorphous & Microcrystalline Silicon Technology 1998 , 1998 , 113
Copyright
Copyright © Materials Research Society 1998

Access options

Get access to the full version of this content by using one of the access options below. (Log in options will check for institutional or personal access. Content may require purchase if you do not have access.)

Article purchase

Temporarily unavailable

References

REFERENCES

1 Chatam, H. and Bhat, P.K., Amorphous Silicon Technology-1989, edited by Thompson, Madan, Taylor, Hamakawa, and Lecomber, , (Mat. Res. Soc. Proc. 149, Pittsburgh, PA, 1992), p. 447–452.Google Scholar
2 Shah, A., Dutta, J., Wyrsch, N., Prasad, K., Curtins, H., Finger, F., Howling, A., and Hollenstein, Ch., Amorphous Silicon Technology-1992. edited by Hamakawa, Thompson, Lecomber, Madan and Schiff, (Mat. Res. Soc. Proc. 258, Pittsburgh, PA, 1992), p. 15–26.Google Scholar
3 Izu, M., Deng, X., Krisko, A., Whelan, K., Young, R., Ovshinsky, H.C., Narasimhan, K.L. and Ovshinsky, S.R., Proc. 23rd IEEE PV Spec. Conf, p. 919 (1993).Google Scholar
4 Deng, X., Jones, S., Liu, T., Izu, M., Ovshinsky, S., Proc.26rd IEEE PV Sp. Conf., p.591 (1997).Google Scholar
5 Deng, X., Jones, S.J., Liu, T., Izu, M., Ovshinsky, S.R. and Hoffman, K., Amorphous Silicon Technology-1997, edited by Hack, Wagner, Schiff, Schropp, and Shimizu, , (Mat. Res. Soc. Proc. 467, Pittsburgh, PA, 1997), p. 795–800.Google Scholar
6 Mackenzie, K.D., Eggert, J.R., Leopold, D.J., Li, Y.M., Paul, W., Phys. Rev. B 31, p. 2198 (1985).Google Scholar
7 Sichanugrist, P., Suzuki, H., Konagai, M., Takahashi, K., Jap. J. Appl. Phys. 25, p. 440 (1986).Google Scholar
8 Heintze, M., Zedlitz, R. and Bauer, G.H., Amorphous Silicon Technology-1993, editors Thompson, Schiff, Madan, Tanaka, Lecomber, , (Mat. Res. Soc. Proc. 297, Pittsburgh, PA, 1993), p.49.Google Scholar