Hostname: page-component-76fb5796d-qxdb6 Total loading time: 0 Render date: 2024-04-25T12:50:29.759Z Has data issue: false hasContentIssue false
  • English
  • Français

Alloying Effect on Mechanical and Chemical Properties of Cold-rolled Ni3(Si,Ti) Foils

Published online by Cambridge University Press:  01 February 2011

Y. Fujimoto ,
Yasuyuki Kaneno  and
Takayuki Takasugi
Y. Fujimoto
Affiliation:
cm0507@mtr.osakafu-u.ac.jp, Osaka Prefecture University, Sakai, Japan
Yasuyuki Kaneno
Affiliation:
kaneno@mtr.osakafu-u.ac.jp, United States
Takayuki Takasugi
Affiliation:
takasugi@mtr.osakafu-u.ac.jp, Osaka Prefecture University, Sakai, Japan
Get access

Abstract

Four kinds of L12-type Ni3(Si,Ti) intermetallic alloys with a quaternary element X (X: Al, Cr, Co and Mo) were warm rolled accompanied by intermediate annealing and then cold rolled to thin foils. The effects of alloying element on microstructure, tensile properties and oxidation resistance of the cold-rolled Ni3(Si,Ti) foils were investigated. The Al-added Ni3(Si,Ti) alloy showed an L12 single-phase microstructure, while the Cr-, Co- and Mo-added Ni3(Si,Ti) alloys exhibited a two-phase microstructure consisting of L12 and fcc Ni solid solution phases. Room-temperature strength of the Ni3(Si,Ti) foils was slightly enhanced by the addition of quaternary element, whereas high-temperature strength was significantly enhanced especially by the addition of Mo and Co. High-temperature tensile elongation was remarkably improved by the addition of all the elements investigated. On the other hand, oxidation resistance was improved by the addition of Al and Cr.

Keywords

additivescold workingpolycrystal
Type
Research Article
Information
MRS Online Proceedings Library (OPL) , Volume 1128: Symposium U – Advanced Intermetallic-Based Alloys for Extreme Environment and Energy Applications , 2008 , 1128-U05-31
Copyright
Copyright © Materials Research Society 2009

Access options

Get access to the full version of this content by using one of the access options below. (Log in options will check for institutional or personal access. Content may require purchase if you do not have access.)

References

REFERENCES

1. Aoki, K. and Izumi, O., J. Jpn. Inst. Met. 43, 1190 (1979).Google Scholar
2. Takasugi, T., Nakajima, M. and Izumi, O., Acta metal. mater. 38, 747 (1990).Google Scholar
3. Takasugi, T. and Izumi, O., Acta metal. mater. 33, 39 (1985).Google Scholar
4. Hirano, T., Demura, M., Kishida, K., Hong, H.U., and Suga, Y., in Structural Intermetallics, edited by Hemker, K.J., Dimiduk, D.M., Clemens, H., Daroria, R., Inui, H., Larsen, J. M., Sikka, V.K., Thomas, M., and Whittenberger, J.D., (TMS, Warrenale, PA, 2001), 765–774.Google Scholar
5. Bojar, Z., Jozwik, P. and Bystrzycki, J., Scr. Mater. 55, 399 (2006).Google Scholar
6. Kaneno, Y., Myoki, T. and Takasugi, T., Int. J. Mater. Res. (Z. Metallkd.), 99, 1229 (2008).Google Scholar
7. Takasugi, T. and Yoshida, M., J. Mater. Sci. 26, 3032 (1991).Google Scholar
8. Takasugi, T. and Yoshida, M., J. Mater. Sci. 26, 3517 (1991).Google Scholar
9. Takasugi, T., Intermetallics 8, 575 (2000).Google Scholar
10. Kaneno, Y. and Takasugi, T., Mater. Sci. Forum 561–565, 411 (2007).Google Scholar
11. Ochiai, S., Oya, Y. and Suzuki, T., Acta metal. 32, 289 (1984).Google Scholar
12. Takasugi, T., Kawai, H. and Kaneno, Y., Mater. Sci. Eng. A329–331, 446 (2002).Google Scholar