Hostname: page-component-848d4c4894-m9kch Total loading time: 0 Render date: 2024-05-15T14:34:27.384Z Has data issue: false hasContentIssue false
  • English
  • Français

Alloying of Al3Ti With Mn and Cr to Form Cubic L12 Phases

Published online by Cambridge University Press:  26 February 2011

J.P. Nic ,
S. Zhang  and
D.E. Mikkola
J.P. Nic
Affiliation:
Dept. of Metallurgical and Materials Engineering,, Michigan Technological University, Houghton,, MI 49931
S. Zhang
Affiliation:
Dept. of Metallurgical and Materials Engineering,, Michigan Technological University, Houghton,, MI 49931
Get access

Abstract

Based on studies of several binary trialuminides, it has been concluded that those with the L12 structure offer the best prospects for developing useful mechanical properties. Further, evaluation of a series of cubic ternary alloys produced by alloying Al3Ti with fourth period transition elements from Cr to Cu has shown that the mechanical properties and lattice parameters of the cubic alloys vary in a consistent manner with the location of the ternary alloying element in the periodic table. These structure/property relationships have been interpreted in terms of the number of d-shell electrons available for bonding. The Cr- and Mn-modified alloys have been shown to be the most attractive in terms of hightemperature structural applications. Finally, the work has resulted in a suggested mechanism for the D022 to Ll2 transformation on alloying.

Type
Research Article
Information
MRS Online Proceedings Library (OPL) , Volume 213: Symposium Q – High-Temperature Ordered Intermetallic Alloys IV , 1990 , 697
Copyright
Copyright © Materials Research Society 1991

Access options

Get access to the full version of this content by using one of the access options below. (Log in options will check for institutional or personal access. Content may require purchase if you do not have access.)

References

REFERENCES

1. Kumar, K.S., Int. Mat. Rev., in press.Google Scholar
2. Yamaguchi, M., Umakoshi, Y. and Yamane, T., Philos. Mag. A 55, 301 (1987).CrossRefGoogle Scholar
3. Umakoshi, Y., Yamaguchi, M., Yamane, T. and Hirano, T., Philos. Mag. A 58, 651 (1988).CrossRefGoogle Scholar
4. Tarnacki, J. and Kim, Y.-W., Scripta Met. 23, 1063 (1989).CrossRefGoogle Scholar
5. Schneibel, J.H. and Porter, W.D in High-Temperature Ordered Intermetallic Alloys III, edited by Liu, C.T., Taub, A.I., Stoloff, N.S. and Koch, C.C. (Mater. Res. Soc. Proc. 133, Pittsburg, PA 1989) 335.Google Scholar
6. Zhang, S., Nic, J.P. and Mikkola, D.E., Scripta Met. 24, 57 (1990).CrossRefGoogle Scholar
7. Kumar, K.S. and Pickens, J.R. in Dispersion Strengthened Aluminum Alloys, edited by Kim, Y.-W. and Griffith, W.M. (TMS Proc., Warrendale, PA 1988), 763.Google Scholar
8. Tarnacki, J. and Kim, Y.-W.Dispersion Strengthened Aluminum Alloys,Google Scholar
9. Nicholson, D.M., Stocks, G.M., Temmerman, W.M., Sterne, P. and Pettifor, D.G. in High-Temperature Ordered Intermetallic Alloys III, edited by Liu, C.T., Taub, A.I., Stoloff, N.S. and Koch, C.C. (Mater. Res. Soc. Proc. 133, Pittsburg, PA 1989) 17.Google Scholar
10. Carlsson, A.E. and Meschter, P.J., J. Mater. Res. 4, 1060 (1989).CrossRefGoogle Scholar
11. Raman, A. and Schubert, K., , Z. Metallkde. 56, 991 (1965).Google Scholar
12. Parfitt, L.J., Smialek, J.L., Nic, J.P. and Mikkola, D.E., Submitted to Scripta Met.Google Scholar