Hostname: page-component-848d4c4894-wzw2p Total loading time: 0 Render date: 2024-05-18T00:30:10.276Z Has data issue: false hasContentIssue false
  • English
  • Français

Compression Behavior of L12 Modified Titanium Trialuminides Alloyed with Chromium and Iron

Published online by Cambridge University Press:  21 March 2011

Tohru Takahashi  and
Tadashi Hasegawa
Tohru Takahashi
Affiliation:
Department of Mechanical Systems Engineering, Faculty of Engineering, Tokyo University of Agriculture and Technology, Koganei, Tokyo 184–8588, Japan
Tadashi Hasegawa
Affiliation:
Department of Mechanical Systems Engineering, Faculty of Engineering, Tokyo University of Agriculture and Technology, Koganei, Tokyo 184–8588, Japan
Get access

Abstract

L12 modified titanium trialuminides have been prepared by replacing 9at.% of the aluminum in Al3Ti with chromium and/or iron. The materials were recrystallized into single phase polycrystals after isothermal forging resulting in an average grain diameter of about 40μm. Lattice parameter of the material containing 9 at.% chromium or 9 at.% iron, are 0.3959nm and 0.3939nm, respectively. The lattice parameters varied linearly with composition between these values for additions of both chromium and iron. Uniaxial compression tests were performed at temperatures ranging from 293K to 1300K. The yield strength is not sensitive to chemical composition within the range of compositions tested. Flow stress serrations of a few % were observed at temperatures around 600K, where intermittent drops in flow stress started immediately after yielding and continued to the end. These serrations were observed up to about 800K. At 900K and above the materials became fully deformable. Quasi steady state flow and strain softening were observed at 1200K and 1300K, respectively, due to dynamic recrystallization.

Type
Research Article
Information
MRS Online Proceedings Library (OPL) , Volume 646 , 2000 , N3.10.1
Copyright
Copyright © Materials Research Society 2001

Access options

Get access to the full version of this content by using one of the access options below. (Log in options will check for institutional or personal access. Content may require purchase if you do not have access.)

References

REFERENCES

1. Yamaguchi, M. and Umakoshi, Y., Progress in Materials Science, 34 (1990), pp.1–148.10.1016/0079-6425(90)90002-QGoogle Scholar
2. Yamaguchi, M., Umakoshi, Y. and Yamane, T., in High-Temperature Ordered Intermetallic Alloys II, edited by Stoloff, N. S., Koch, C.C., Liu, C.T. and Izumi, O., (Mater. Res. Soc. Proc. 81, Pittsburgh, PA, 1987), pp.275–286.Google Scholar
3. Yamaguchi, M., Nishitani, S.R. and Shirai, Y., in High Temperature Aluminides and Intermetallics, edited by Baker, I., Darolia, R., Whittenberger, J.D. and Yoo, M.H., (TMS, Warrendale, PA, 1990), p.63.Google Scholar
4. Umakoshi, Y., Yamaguchi, M., Yamane, T. and Hirano, T., Phil. Mag., A58, 651 (1988).10.1080/01418618808209943Google Scholar
5. Turner, C.D., Powers, W.O. and Wert, J.A., Acta metall., 37, 2635 (1989).10.1016/0001-6160(89)90296-4Google Scholar
6. Mabuchi, H., Hirukawa, K. and Nakayama, Y., Scripta metall., 23, 1761 (1989).10.1016/0036-9748(89)90357-8Google Scholar
7. Kumar, K.S., Brown, S.A. and Whittenberger, J.D., in High-Temperature Ordered Intermetallic Alloys IV, edited by Johnson, L.A., Pope, D.P. and Stiegler, J.O., (Mater. Res. Soc. Proc. 213, Pittsburgh, PA, 1991), pp.481–486.Google Scholar
8. Kumar, K.S. and Brown, S.A., in High-Temperature Ordered Intermetallic Alloys V, edited by Baker, I., Darolia, R., Whittenberger, J.D. and Yoo, M.H., (Mater. Res. Soc. Proc. 288, Pittsburgh, PA, 1993), pp.781–786.Google Scholar
9. Kim, S.M., Kogachi, M., Kameyama, A. and Morris, D.G., Acta metal. mater., 43, 3139 (1995).10.1016/0956-7151(95)00010-SGoogle Scholar
10. Takahashi, T., Endo, K., Kaizu, S. and Hasegawa, T., in High-Temperature Ordered Intermetallic Alloys V, edited by Baker, I., Darolia, R., Whittenberger, J.D. and Yoo, M.H., (Mater. Res. Soc. Proc. 288, Pittsburgh, PA, 1993), pp.711–716.Google Scholar
11. Takahashi, T. and Hasegawa, T., in High-Temperature Ordered Intermetallic Alloys VI, edited by Horton, J.A., Baker, I., Hanada, S., Noebe, R.D. and Schwarz, D.S., by Baker, I., Darolia, R., Whittenberger, J.D. and Yoo, M.H., (Mater. Res. Soc. Proc. 364, Pittsburgh, PA, 1995), pp.1235–1240.Google Scholar
12. Wu, Z.L. and Pope, D.P., in Structural Intermetallics, edited by Darolia, R., Lewandowski, J.J., Liu, C.T., Martin, P.L., Miracle, D.B. and Nathal, M.V., (TMS, Warrendale, PA, 1993), p.107.Google Scholar
13. Takahashi, T., Asano, K., Ashida, D., Murakoshi, T. and Hasegawa, T., presented at the Thermec 2000 International Conference, Las Vegas, NV, 2000 (unpublished).Google Scholar
14. Wu, Z.L., Pope, D.P. and Vitek, V., Acta metall. mater., 42, 3577 (1994).10.1016/0956-7151(94)90490-1Google Scholar