Hostname: page-component-8448b6f56d-mp689 Total loading time: 0 Render date: 2024-04-20T01:59:58.568Z Has data issue: false hasContentIssue false
  • English
  • Français

Fabrication and Simulation of Amorphous Carbon Cantilever Structures

Published online by Cambridge University Press:  15 February 2011

Daniel H.C. Chua ,
W.I. Milne ,
L.J. Yu ,
D. Sheeja  and
B.K. Tay
Daniel H.C. Chua
Affiliation:
University of Cambridge, Engineering Dept, Cambridge, England, CB2 1PZ, UK
W.I. Milne
Affiliation:
University of Cambridge, Engineering Dept, Cambridge, England, CB2 1PZ, UK
L.J. Yu
Affiliation:
School of Electrical and Electronic Engineering, Nanyang Technological University, Singapore
D. Sheeja
Affiliation:
School of Electrical and Electronic Engineering, Nanyang Technological University, Singapore
B.K. Tay
Affiliation:
School of Electrical and Electronic Engineering, Nanyang Technological University, Singapore
Get access

Abstract

In view of the superior bio-compatibility of amorphous carbon (a-C) films, a study has been carried out on the fabrication and simulation of free-standing amorphous carbon microcantilevers. The fabrication of micro-structure was carried out by a single photolithography step. A 1.7micro-meter thick, low stress, smooth (Rrms ∼0.75nm) a-C films were deposited by filtered cathodic vacuum arc deposition (FCVA) system, in conjunction with high substrate pulse biasing on patterned n-doped Si >100< substrates. Subsequently, the photoresist was lifted-off in acetone and which is followed by undercutting of the cantilever structures in 40% KOH solution. The deflection of the free-standing cantilever structures was measured using an optical profiler, and the stress in the a-C cantilever structures was independently calculated from the deflection of the cantilever beam and the total tilt angle. This stress value is compared with the stress in the film measured from the film-substrate sandwich by radius of curvature technique. Simulation of the cantilever assembly was carried out to obtain the deflection and stress distribution. The simulated parameters are compared with the experimental results.

Type
Research Article
Information
MRS Online Proceedings Library (OPL) , Volume 773: Symposium N – Biomicroelectromechanical Systems (BioMEMS) , 2003 , N3.2
Copyright
Copyright © Materials Research Society 2003

Access options

Get access to the full version of this content by using one of the access options below. (Log in options will check for institutional or personal access. Content may require purchase if you do not have access.)

References

1. Voevodin, A., Donley, M.S. and Zabinski, J.S., Surf. Coat. Technolo. 52, 42 (1997).Google Scholar
2. Lifshitz, Y., Lempert, G.D., Grossman, E., Phy. Rev. Lett. 72, 2753 (1994).Google Scholar
3. Schwan, J., Ulrich, S., Roth, H., Ehrhardt, H., Silva, S.R.P., Robertson, J., Samlenski, R. and Brenn, R., J. Appl. Phys. 79, 1416 (1996).Google Scholar
4. Shi, X., Tu, Y. Q., Tan, H. S., Tay, B. K. and Milne, W. I., IEEE Transactions on Plasma Science, 24, 1309 (1996).Google Scholar
5. Anders, S., Diaz, J., Ager, J.W., Lo, R.Y., Bogy, D.B., Appl. Phys. Lett., 71, 3367 (1997).Google Scholar
6. Shi, X., Tay, B.K., Tan, H.S., Zhong, Li, Tu, Y.Q., Silva, S.R.P., Milne, W.I., J. of Appl. Phys., 79, 7234–7240 (1996).Google Scholar
7. Pharr, G. M., Callahan, D. L., McAdams, S. D., Tsui, T. Y., Anders, S., Anders, A., Ager, J. W. III, Brown, I.G., Bhatia, C.S., Silvab, S.R.P. and Robertson, J., Appl. Phys. Lett. 68, 779–782 (1996).Google Scholar
8. Anders, S., Anders, A., Brown, I.G., Wei, B., Komvopoulos, K., Ager, J.W. III and Yu, K.M., Surface and Coating Technology, 68/69, 388 (1994).Google Scholar
9. Fallon, P. J., Veerasamy, V. S., Davis, C. A., Robertson, J., Amarathunga, G. A. J., Milne, W.I. and Koskinen, J., Phys. Rev. B., 48, 4777 (1993).Google Scholar
10. McKenzie, D. R., Muller, D., Paithorpe, B.A., Wang, Z. H., Kravtchinskaia, E., Segal, D., et al., Diamond Related Materials, 1, 51 (1991).Google Scholar
11. Shi, X., Tu, Y. Q., Tan, H. S., Tay, B. K. and Milne, W. I., IEEE Transactions on Plasma Science, 24, 1309 (1996).Google Scholar
12. Kumar, Sushil, Dixit, P.N., Sarangi, D. and Bhattacharyya, R., Journal of Applied Physics, 85 (7) 3866–3877 (1999).Google Scholar
13. He, X.M., walter, K.C., Nastasi, M., Lee, S.T. and Fung, M.K., J. Vac. Sci. Technol. A 18 (5) 2143–2148 (2000).Google Scholar
14. Damasceno, J.C., Camargo, S.S. Jr, Freire, F.L. Jr and carius, R, Surface and Coatings Technology, 133-134, 247–252 (2000).Google Scholar
15. Chhowalla, M. and Amaratunga, G.A., Journal of Materials Research, 16 (1), 5–8 (2001).Google Scholar
16. Sheeja, D., Tay, B.K., Yu, L.J. and Lau, S.P., Surface & Coatings Technology, 154 (2), 289–293 (2002).Google Scholar
17. Tay, B.K., Sheeja, D. and Yu, L.J., Diamond and Related Materials (2003) (in press).Google Scholar
18. Fang, W. and Wickert, J. A., J. Micromech. Microeng. 6, 301–309 (1996).Google Scholar
19. Fang, W. and Wickert, J. A., J. Micromech. Microeng. 5, 276–281 (1995).Google Scholar
20. Fang, W. and Wickert, J.A., J. Micromech. Microeng. 4, 116–122 (1994).Google Scholar
21. Chen, K.S and Ou, K.S, J. Micromech. Microeng. 12, 917–924 (2002).Google Scholar