Hostname: page-component-76fb5796d-wq484 Total loading time: 0 Render date: 2024-04-27T19:26:20.010Z Has data issue: false hasContentIssue false
  • English
  • Français

Friction and Wear Properties of ALD Coated MEMS

Published online by Cambridge University Press:  01 February 2011

Corina Nistorica ,
Igor Gory ,
George D. Skidmore ,
Fadziso M. Mantiziba  and
Bruce E. Gnade
Corina Nistorica
Affiliation:
Zyvex Corporation, 1321 N. Plano Road, Richardson, Texas 75081
Igor Gory
Affiliation:
Zyvex Corporation, 1321 N. Plano Road, Richardson, Texas 75081
George D. Skidmore
Affiliation:
Zyvex Corporation, 1321 N. Plano Road, Richardson, Texas 75081
Fadziso M. Mantiziba
Affiliation:
Department of Electrical Engineering, University of Texas at Dallas, Richardson, Texas 75083
Bruce E. Gnade
Affiliation:
Department of Electrical Engineering, University of Texas at Dallas, Richardson, Texas 75083
Get access

Abstract

A comparative study of the microtribological properties of native oxide covered single crystal silicon and silicon coated with atomic layer deposited (ALD) alumina films is presented. The dry friction and wear behavior were investigated using a novel microelectromechanical system (MEMS) tribotester. The coefficient of friction for alumina coated surfaces and for silicon uncoated surfaces was monitored before and after wear. The friction versus normal load curves of uncoated silicon can be described by a Johnson-Kendall-Roberts model with pressure dependent shear strength while for the alumina coated surfaces, a linear dependence between the friction force and the normal load was found. Both uncoated silicon surfaces and alumina coated surfaces showed a decrease of the friction force with the number of sliding cycles.

Type
Research Article
Information
MRS Online Proceedings Library (OPL) , Volume 841: Symposium R – Fundamentals of Nanoindentation and Nanotribology III , 2004 , R9.16
Copyright
Copyright © Materials Research Society 2005

Access options

Get access to the full version of this content by using one of the access options below. (Log in options will check for institutional or personal access. Content may require purchase if you do not have access.)

References

REFERENCES

1. Liu, H., Bhushnan, B., Ultramicroscopy 97, 321 (2003).Google Scholar
2. Prasad, R., MacDonald, N. and Taylor, D., Proc. of the 8th International Conference on Solid-State Sensors and Actuators, Stockholm, Sweden, 244 (1995).Google Scholar
3. Tas, N. R., Gui, C., and Elwenspoek, M., Proceedings of the 10th Annual International Workshop on Micro Electro Mechanical Systems, 215 (1997).Google Scholar
4. Wang, W., Wang, Y., Bao, H., Xiong, B., Bao, M., Sensor Actuat. A 3208, (2002).Google Scholar
5. Liu, H., Ahmed, S. I.-U., Scherge, M, Thin Solid Films 381, 135 (2001).Google Scholar
6. Maboudian, Roya, Robert Ashurst, W. and Carraro, C., Tribol. Lett. 12, 95 (2002).Google Scholar
7. de Boer, M. P. and Mayer, T. M., MRS Bulletin 26, 302 (2001).Google Scholar
8. Ashurst, W. R., Jang, Y. J., Magagnin, L., Carraro, C., Sung, M. M., and Maboudian, R., Technical Digest of the 17th IEEE International Conference on Micro Electro Mechanical Systems, Maastricht, The Netherlands, 153 (2004).Google Scholar
9. Mayer, T. M., Elam, J. W., George, S. M., Kotula, P. G., Goeke, R. S., Applied Physics Letters 82, 2883 (2003).Google Scholar
10. Davis, C. Q., Karu, Z. Z., Freeman, D. M., Proceedings of the International Symposium on Computer Vision, 7 (1995).Google Scholar
11. Johnson, K.L., Kendall, K., Roberts, A.D., Proc. R. Soc. Lond. Ser.A 324, 301 (1974).Google Scholar
12. Zhao, X., Bhushan, B., Wear 223, 66 (1998).Google Scholar
13. Tanner, D.M., Walraven, J.A., Irwin, L. W., Dugger, M. T., Smith, N. F., Eaton, W. P., Miller, W. M., Miller, S. L., Proc. of the IEEE International Reliability Physics Symposium, March 21–25, San Diego, CA, 189 (1999).Google Scholar
14. Singer, I.L., MRS Bulletin 23, 37 (1998).Google Scholar
15. Rainforth, W.M., Ceramics International 22, 365 (1996).Google Scholar
16. Li, X., Bhushan, B., Takashima, K., Baek, C.–W., Kim, Y.–K., Ultramicroscopy 97, 481 (2003).Google Scholar
17. Jahanmir, S., Dong, X., J. Tribol. 114, 403 (1992).Google Scholar