Hostname: page-component-54dcc4c588-b5cpw Total loading time: 0 Render date: 2025-09-28T15:45:01.231Z Has data issue: false hasContentIssue false
  • English
  • Français

The Hardness and Elastic Modulus of TiN Films as Determined by Ultra-Low Load Indentation

Published online by Cambridge University Press:  16 February 2011

M. E. O'Hern ,
W. C. Oliver ,
C. J. McHargue ,
D. S. Rickerby  and
S. J. Bull
M. E. O'Hern
Affiliation:
Oak Ridge National Laboratory, P.O. Box 2008, Oak Ridge, TN 37831-6118.
W. C. Oliver
Affiliation:
Oak Ridge National Laboratory, P.O. Box 2008, Oak Ridge, TN 37831-6118.
C. J. McHargue
Affiliation:
Oak Ridge National Laboratory, P.O. Box 2008, Oak Ridge, TN 37831-6118.
D. S. Rickerby
Affiliation:
Materials Development Division, Harwell Laboratory, Didcot, Oxfordshire OX11 ORA, UK
S. J. Bull
Affiliation:
Materials Development Division, Harwell Laboratory, Didcot, Oxfordshire OX11 ORA, UK
Get access

Abstract

The mechanical properties of a series of titanium nitride films on stainless steel substrates have been evaluated using an indentation technique with a mechanical properties microprobe (MPM). The MPM makes possible measurement of film properties without contribution by the substrate material. The titanium nitride films were deposited with a PVD technique known as sputter ion plating (SIP). Deposition substrate bias was varied from 0 to −120 V, while keeping other deposition parameters constant. With increasing negative substrate bias, dramatic increases in hardness and elastic modulus have been observed.

Information

Type
Research Article
Information
MRS Online Proceedings Library (OPL) , Volume 188: Symposium K – Thin Films: Stresses and Mechanical Properties II , 1990 , 139
Copyright
Copyright © Materials Research Society 1990

Access options

Get access to the full version of this content by using one of the access options below. (Log in options will check for institutional or personal access. Content may require purchase if you do not have access.)

Article purchase

Temporarily unavailable

References

REFERENCES

1. Musil, J., Thin Solid Films, 136(1986)229–239.Google Scholar
2. Rickerby, D. S. and Burnett, P. J., Thin Solid Films, 157(1988)195–222.Google Scholar
3. O'Hern, Michael E., Parrish, Robert H. and Oliver, Warren C., Thin Solid Films, 181(1989)357–363.Google Scholar
4. Joslin, D. L., O'Hern, M. E., McHargue, C. J., Clausing, R. E. and Oliver, W. C. in Infrared Systems and Components III, SPIE volume 1050 (1989)218–225.Google Scholar
5. O'Hern, M. E., McHargue, C. J.,Clausing, R. E., Oliver, W. C. and Parrish, R. H. in Technology Update on Diamond Films, Chang, R. P. H., Nelson, D. and Hiraki, A., eds., Materials Research Society, Pittsburgh, 1989, pp 131–137.Google Scholar
6. Rickerby, D. S. and Newbery, R. B., Vacuum, 38(1988)161–166 Google Scholar
7. Pethica, J. B., Hutchings, R. and Oliver, W. C., Phil. Mag. A48 (1983) 593.Google Scholar
8. Doerner, M. F. and Nix, W. D., J. Mater. Res., 1(1986)601.Google Scholar
9. Thornton, J. A., J. Vac. Sci. Techhnol., 11(1974)666.Google Scholar