Hostname: page-component-8448b6f56d-xtgtn Total loading time: 0 Render date: 2024-04-19T16:33:47.862Z Has data issue: false hasContentIssue false
  • English
  • Français

Influence of Grain Interaction on the Mechanical Behavior in Shape Memory Material in Flexion Test

Published online by Cambridge University Press:  01 February 2011

Jacinto Cortés ,
Fernando N. García ,
José G. González ,
Horacio Flores  and
Alberto Reyes
Jacinto Cortés
Affiliation:
Centro Tecnológico Aragón, FES Argón, UNAM. Edo. de México, México, C. P. 57130.
Fernando N. García
Affiliation:
Centro Tecnológico Aragón, FES Argón, UNAM. Edo. de México, México, C. P. 57130.
José G. González
Affiliation:
Instituto de Investigaciones en Materiales, UNAM. México D.F. México.
Horacio Flores
Affiliation:
Maestría en Procesos y Materiales, Universidad Autónoma de Zacatecas, Zacatecas, México.
Alberto Reyes
Affiliation:
IME, FES Aragón, UNAM. Edo. de México, México, C. P. 57130.
Get access

Abstract

An experimental study of the mechanical properties of a Cu-Al-Be shape memory alloy is presented. The samples are tested in a cantilever arrangement. They consist of polycrystalline thin plates of shape memory material with a MS near 0 °C and a monocrystalline sample with MS near −90 °C. The measurements are made with strain gauges attached to the top side of the samples. In these conditions, strain Vs load curves are obtained. A polycrystalline sample is instrumented and tested and then it is cut into three samples for further testing. The results show a relationship between the transformation stress and the sample grain size which differs from the typical Hall-Petch relationship. The analysis of transformation plane stress diagrams shows the development of a stress component perpendicular to those induced by the applied load.

Type
Research Article
Information
MRS Online Proceedings Library (OPL) , Volume 1243: Symposium 5 – Advanced Structural Materials , 2009 , 17
Copyright
Copyright © Materials Research Society 2010

Access options

Get access to the full version of this content by using one of the access options below. (Log in options will check for institutional or personal access. Content may require purchase if you do not have access.)

References

REFERENCES

1. Sakamoto, H. and Shimizu, K.. Experimental Investigation of Cyclic Deformation and Fatigue Behavior of Polycrystalline Cu-Al-Ni Shape memory alloys above Ms . Transactions of Japan Institute of Metals, 8, pp 592–600, (1986).Google Scholar
2. Somerday, M., Comstock, R. J. JR. And Wert, J. A.. Effect of grain size on the observed pseudoelastic behavior of a Cu-Zn-Al shape memory alloy. Metallurgical and Materials Transactions A. 28A. pp. 2335–2341(1997).Google Scholar
3. Sure, G. N. and Brown, L. C.. The mechanical properties of refined β Cu-Al-Ni strainmemory alloys. Metallurgical Transactions A. 5a. pp 613–1621 (1984).Google Scholar
4. Leu, S. S., Chen, Y. C., Jean, R. D.. Effect of rapid solidification on mechanical properties of Cu-Al-Ni shape memory alloys. Journal of Materials Science. 27. pp 2792–2798, (1992).Google Scholar
5. Otsuka, K. and Wayman, C. M.. Introduction to shape memory materials. Shape memory materials. Cambridge University Press. pp. 1–48 (1998)Google Scholar
6. Kaouache, B., Inal, K., Berveiller, S., Eberhardt, A. and Patoor, E.. Martensitic transformation criteria in Cu–Al–Be shape memory alloy. In situ analysis. Materials Science and Engineering A. 438–440, 773 (2006)Google Scholar
7. Buchheit, T. E. and Wert, J. A.. Modeling the Effects of Stress State and Crystal Orientation on the Stress-Induced Transformation of Ni-Ti Single Crystals. Metallurgical and Materials Transactions A. 25A. pp. 2383–2389. (1994).Google Scholar